John Lewis REIGN CRYSTAL PENDANT User manual

REIGN CRYSTAL PENDANT
USER GUIDE
Caring for
your product
We recommend cleaning with a soft dry cloth.
Do not use abrasive materials as these will damage the finish.
Indoors use only.
Aftercare and
Troubleshooting
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
Replace bulbs from John Lewis or established brand of the same type
and compatibility
If you experience any unresolvable technical issues with the product,
contact your nearest John Lewis & Partners shop or John Lewis &
Partner Technical Support on 03301 230106.
Specification
Recommended bulb: G9 halogen or G9 LED
Max. power: 3x28W
Bulb not included
Voltage: 220 –240V, 50Hz
IP rating: 20
Weight: 2.85kg
5 year guarantee
At JohnLewis& Partners we test every light to high quality standards so we are
able to offer you a 5 year guarantee.
Recycling
This symbol
indicates that this product should not be treated as normal
household waste and it should be recycled. John Lewis & Partners do not
operate instore take back, but as members of the Distributor Take Back
scheme have funded the development and upgrade of recycling facilities across
the UK. Please take it to your nearest collection facility or for further details
contact your local council or visit www.recycle-more.co.uk.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made inChina
Please retain these instructions for future reference.

Introduction
Thank you for purchasing this Reign Crystal
Pendant.
Please read the instructions carefully before
use to ensure safe and satisfactory operation
of this product.
Product assembly
1
Ensure the mains electricity supply switched off at the
fuse board.
Step 1
If removing an existing fitting, note down all wiring
connections.
Put the centre rod into the top of lampholder base,
and then secure with grub screw using Allen key
(provided)
Warnings
This product is Class I and must be earthed.
This fitting should be fitted in accordance with IEE Regulations and the
Building
Regulations. If in any doubt, or where required by law, consult a competent
person who is registered with an electrical self-certification scheme.
Further information is available online or from your Local Authority.
To prevent electric shock,switch off at the mains supply before installing or
maintaining this fitting. Ensure otherpersons cannot restore the electricity
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician. It is the installer’s responsibility to ensure that the fixings
and plugs used are suitable for the surface you are fixing your product on.
If replacing an existing fitting, make a note of the connections.
Always use the correct type and power bulb. Never exceed the power stated.
When changing a bulb, always switch off at the mains and allow the old bulb
to cool down before handling. Dispose of used bulbs carefully.
The flexible cable on this luminaire, if damaged, shall only be replaced by the
manufacturer or his service agent or a similar qualified person.
Caution! The bulb and surrounding parts can become hot during
use
2
A
Step 2
Ensure that the bracket (supplied) is fixed to a wooden
joist in the ceiling using screws (supplied) or use a
suitable fixing to the ceiling which will support the weight
of the fitting.
The weight of the fitting must be supported by the
suspension bracket and not the flexible cable.
Adjust the chain to the required length, ensure the cable
is longer than the chain, feed the flexible cable through
the chain links and into the ceiling cup. Ensure that no
strain is placed on the cable.
Connect cables to terminals as shown below.
Check all wires are tight in the terminal block and no
loose strands are left out.
Cover with insulating tape (not included).
Step 3
Push up ceiling cup and secure with grub screws provided
Parts list
Description
Image
Quantity
A
3
Step 4
Attach the correct type and wattage bulb to the
lamp holder (bulb not included).
The maximum power indicated must not be
exceeded.
Insert the crystal rulers into the holes gently as per
illustration.
Switch on the electricity supply at the fuse board.
01
02