John Lewis Showwood Bed User manual

Showwood Bed
MTO
Thank you for purchasing this Showwood Bed. Please read the instructions carefully before use to ensure
safe and satisfactory operation of this product.
Double
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/7

Fitting and parts checklist
A
B
C
D
F
G
H
J
L
K
I
E
M5 Allen Key x 1
M4 Allen Key x 1
Side Caps x 14
Centre Caps x 7
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 14
Wide Slats x 16
Centre Rail x 1
Legs x 4
Wooden Base (Headboard) x 2
Parts
Fittings
7
8
HEAD
M6 Washer x 10
M8 Washer x 2
M6 X 40mm Bolt x 8
2/7
M6 x 55mm Bolt x 4
M8 x 50mm Bolt x 4
Wide Centre Caps x 8
Wide Side Caps x 16
M8 Spring Washer x 4

Note: Make sure the Side Rail (3) which has sticker (HEAD) is attach on Headboard
3/7
Step One
Step Two
Attach the Wooden Base (8) into the side on the Headboard (1) using the M6 x 55mm Bolt (G), and M8 Washer (J).
Do not tighthen the bolt until all part attached.
1
J.G.8.
M8 Washer x 2
Wooden Base
x 2 M6 x 55mm x 2
M4 Allen Key
x 1
B.
M4 (B)
M6 x 55mm(G)
M10 x Washer(J)
8
8
1
Before attach the Side Rails (3) with the side of Headboard (1), rest the headboard down to the carpeted or soft
flooring as shown in Fig 1. Only then you can attach both using M6 x 55mm Bolt(G) and M6 Washer (F) as
shown in Fig.2.
Continue attach the Side Rails (3) to the Front Headboard (1) using M6 x 40mm Bolt (E) and M6 Washer (F).
Adjust the Side Rails (3) with the Headboard (1) and make sure the edges align perfectly.Tighten M6 x 55mm Bolt(G)
first using M4 Allen Key (B), and then continue to tighthen the M6 x 40mm Bolt (E) to
secure in place
HEAD
Carpeted or
soft flooring
Flip over
Fig.1
x2x2
Fig.2 Fig.3
HEAD
3
M6 x 55mm (G)
M6 Washer (F)
SIDE
1
M6 x 40mm Bolt
x 4
M6 x 55mm Bolt
x 2
E.
G. F.
M6 Washer x 6
HEAD
1
3
M6 x 40mm
(E)
(F)
(F)
(G)
M4(B)
Tighten
first
Tighten
last

Step Four
Step Three
Lower the Centre Rail (6) into the pre-drilled holes of the Headboard (1) and Footboard (2) and attach with
M6 x 40mm Bolt (E) and M6 Washer(F) and fully tighten bolts with M4 Allen Key (A) as shown in Fig.4.
You can now tighten the bolts at the Footboard using M5 Allen Key (A) for the Footboard(2) so all
fastenings are now tightened.
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
NEXT STEP
4/7
Bracket
Side Rail
2
3
Fig.4
x2
K. L.
HEAD
3
1
3
2
M8 Spring
Washer x 4
M8 x 50mm Bolt
x 4
M8 x 50mm (L)
M8 Spring Washer (K)
Now attach the Footboard (2) to the Side Rails (3) using M8 x 50mm (L) with M8 Spring Washer (K) and hand-
tighten to loosely secure parts together as shown in Fig.4. Do not tighthen bolts with M5 Allen Key (A) until you
have inserted the Centre Rail in the next step.
Bracket
Side Rail
2
3
Fig.4
x2
M5(A)
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
M4 Allen Key
x 1
M5 Allen Key
x 1
A. B.
M6 x 40mm Bolt
x 4
E. F.
M6 Washer
x 4
F
i
g
.
5
5
1
2
And
6
M6 x 40mm (E) (F)
M4 (B)
HEAD
6

2 Lines
Normal slats
1 Line
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
D
I
4
5
(x8)
(x7)
4.
5.
C.
D
I.
H.
Side Caps x 14
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 14
Step Six
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x15). (Please note the Wide Slats must be inserted with the Wide Centre Caps (H) and Wide
Side Caps (I)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
H
5
5
Centre Caps x 7
H
I
I
D
D
4
4
5
5
C
Starting with the Headboard (1), insert the Legs (7) into the pre-drilled holes on the underside of the Headboard (1)
and twist to secure, as shown in the diagram below.
Legs x 4
7.
5/7
Step Five
77
FOOTBOARD
2
3
1
HEADBOARD
3
Note: Before proceed to the next step, ensure the wooden base on each part are parallel towards each other
by adjusting the bolt on the bottom.

6/7
Step Seven
This bed is now ready to use.

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
7/7