John Lewis Duhrer 836 03704 User manual

Duhrer Round Dining Table
Stock Number: 836 03704
H75 W120 D120cm
YNG TAL 14 / DMT1 D: 26.11.2019 / RN 008.

Thank you for purchasing the Duhrer Round Dining Table. Please read the instructions and warnings carefully before
use, to ensure safe and satisfactory operation of this product.
At John Lewis, we are committed to making great products possible.
From our in-house Design Team, to our Buyers, we work together to bring great design to life.
Our expert Product Technologists work collaboratively with our buyers and suppliers to assure the legality, safety
and quality of the product we sell.
We are all committed to designing and developing products to the highest industry standarts.
We hope you are happy with your product and welcome any feedback or comments you may have.
The John Lewis Team
1
Tools Required
Time to assemble
1 hour
People to assemble

2
Important safety information
Warnings
The product should only be used on firm, level ground.
Keep small parts ot of reach of children.
Ensure the product is fully assembled as illustrated before use.
Do's
Check the pack and make sure you have all the parts listed.
Check all screws or bolts are tightened and inspect regularly.
Make sure the legs remain in contact with the ground at all times.
Dont's
Do not over tighten screws or bolts.
Do not stand on the product.
Don not use power tools to construct as overtightening and panel failure may occur.

Leg Frame
3
Your dining table
Ref
1
Dimensions Qty
H4 W160 D95cm
H11 W50 D95cm
1
Description
22
Top Panel
Dimensions
Stock number: 836 03704
Dining table original size: H75 W120 D120cm
Dining table extended size: H75 W165 D120cm
2
1

4
Fixtures and fittings
Fixtures and fittings
supplied (actual size)
Ref Description Dimensions Qty
A10mm x 35mm 8
Wooden Dowel
Fixtures and fittings
supplied (not actual size)
Ref
D
Description Dimensions Qty
4
Hex Nut
C4
Fixing Head
B8mm x 62mm 4
Headless Bolt
F1
Wedge
E1
Wrench

5
Product assembly
Duhrer Round Dining Table
836 03704
Step 1
Parts, fittings and tools
A B 2
Step 2
Parts, fittings and tools
C D E 21 2
2
A
A
B
B
1
2
2
1234
To tighten the leg assembly, use
the supplied wrench and turn the
hex nut clockwise until fully
fastened.
Place the leg frame by aligning the
dowels and the headless bolts to
the corresponding holes.
Then place the fixing head as
shown above.
Slightly fix the hex nut on the
headless bolt by hand.
D
E
C
IMPORTANT
Do not release the catch
locks under the top panel
before fixing the leg frames.
Use of the extension
mechanism prior to leg
assembly will cause the
panels to detach.

6
Duhrer Round Dining Table
836 03704
Step 3
Parts, fittings and tools
Step 4
Parts, fittings and tools

7
Duhrer Round Dining Table
836 03704
Step 5
Parts, fittings and tools
Step 6
Parts, fittings and tools
Step 7
Parts, fittings and tools

8
Safety Instructions
General warnings
Never drag furniture when moving it, always lift it. Periodically check all fixings to ensure none have come loose and
re-tighten where necessary. Please take care when handling or moving the furniture as careless handling may cause
damage or injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
person. No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
Specific warnings for heavy items
It is recommended that before moving heavy objects to a new location they are completely dis-assembled to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this. (For fully or partial
assemble items).
Storage units over 600mm
Installation shall be carried out exactly according to the manufacturer’s instructions – otherwise a safety risk can
occur if incorrectly installed; a warning shall be given to the consumer to notify them of related risks.
Care Instructions
Wood Furniture
Wood displays dierent grain patterns depending on which way they cut - for example, the ‘medullary ray’ which can
appear on oak furniture is a mark of good quality timber - these are just characteristics of the natural beauty of the
wood. Some furniture is also deliberately aged and rustic.

Wood veneers also allow distinctive patterns to be created on flat surfaces, such as table tops and drawer fronts by
the way the slivers are arranged.

All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade from items that
have been previously purchased.

How to care for your wood or painted furniture
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.

Waxed furniture will need to be given a coat of beeswax a couple of times a year to help maintain its luster.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by building up over
time.

Make sure all surfaces are protected from heat and liquids by mats and coasters. Wipe up spills immediately and
ensure that a mat or pad is placed under paper if you are writing.
Extendable dining tables should be left extended for the first few months to avoid an uneven appearance. Likewise,
lamps and ornaments should also be moved regularly.

Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to heat
sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity caused by central
heating can cause damage such as warping.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Please leave a review.