John Lewis Napoli 80310604 User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
his product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
his product takes approximately 50 MINUTES to assemble with 2 PEOPLE.
he fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
John L wis
Stock Code: 80310604
Napoli ch st 3 draw rs
hank you for purchasing this Napoli chest 3 drawers. Please read the instructions carefully before use
to ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
N c ssary Tools
Screwdriver
002030405060708090 00 020 30 40 50
023456
Ruler/tape
measure Small hammer
Drill Eye protection
NAN 02/14
Page 1

Metal dowel x 26 Middle cam lock x 16
Wooden dowel x 32
30mm
12mm
10.5mm
Short cam lock x 10
30mm Screw x 12
11mm Euroscrew x 12 15mm Screw x 2
25mm Nail x 30
Runners 3
A B C
G
L
H
M
D E F
I
N
Bracket “L” x 2
30mm Screw x 20
Z2
Z1
Nail guide x 1
Support foot x 4
O
Spacer x 4
Page 2
NAN 02/14
Fittings checklist

1
2
2
x 2
8
x 2
9
13
9
16
14 15
x 2
11
x 2
12
x 2
10
3
6
7
7
7
7
4
5
4
5
Page 3
NAN 02/14
Parts checklist

1
3
A
A
A
A
Page 4
Step by step assembly instructi ns
Step One
Attach 4x metal dowels (A) into the pre drilled holes on top panel (1) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
Attach 4x metal dowels (A) into the pre drilled holes on bottom panel (3) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
1.
2.
NAN 02/14

C
N
C
C
N
I
I
E
E
E
E
C
C
4
4
O
O
Page 5
NAN 02/14
Step by step assembly instructi ns
Step Two
Attach 6x wooden dowels (E) into the pre drilled holes as shown on side panel (2) as shown.
Place 4x cam lock (C) into the holes on side panels (2) as shown, arrow pointing towards the bolt.
Attach 2x metal dowels (A) into the pre drilled holes on side panel (2) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
Repeat for the other side panel
1.
2.
Step Three
Attach 4x wooden dowels (E) into the pre drilled holes on rails (4) as shown.
Place 4x cam lock (C) into the holes on side panels (4) as shown, arrow pointing towards the bolt.
Fix the two bracket (N) losely onto one rail (4) using screw (I) and spacer (O).
1.
2.
3.
C
C
C
E
E
2
C
A
C

C
E
E
5
C
C
Page 6
Step by step assembly instructi ns
Step Four
Attach 2x wooden dowels (E) into the pre drilled holes on rail (5) as shown.
Place 2x cam lock (C) into the holes on side panels (5) as shown, arrow pointing towards the bolt.
Repeat for the other rail
1.
2.
Step Five
Attach 2x metal dowels (A) into the pre drilled holes, in only two of four rail (7) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
1.
NAN 02/14
A
77
A
A
A

Page 7
NAN 02/14
2
B
B
B
7
7
Step by step assembly instructi ns
Step Si
Fix two rails (7) onto side panel (2) using 6x screw (B).
Pay attention to fix in the front part of side panel (2) the rail with the metal dowels fixed as show.
Repeat for the other side panel
1.
Step Seven
Attach rails (4) (5) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E) are
aligned correctly with the holes of matching parts before attaching.
Pay attention to the correct position of rail (4) with the bracket (N) fixed .
Secure rails (4) (5) to side panels (2) using a screwdriver to turn fitting (C) clockwise to fix.
1.
2
2
2
1
A
C
C
4
5
4
5

Page 8
NAN 02/14
1
2
1
2
2
A
C
2
2
3
C
1
2
A
Step by step assembly instructi ns
Step Eight
Attach top panel (1) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E) are
aligned correctly with the holes of matching parts before attaching.
Secure top panel (1) onto side panels (2) using a screwdriver to turn fitting (C) clockwise to fix.
1.
2.
Step Nine
Attach bottom panel (3) onto side panels (2) as shown. Ensure metal dowels (A) and wooden dowels (E)
are aligned correctly with the holes of matching parts before attaching.
Secure bottom panel (3) onto side panels (2) using a screwdriver to turn fitting (C) clockwise to fix.
1.
2.

3
6
B
B
M
M
Step by step assembly instructi ns
Step Ten
Position back panel (6) as shown
Attach 4x support foot (M) to bottom (3) with 8x screw(B).
1.
2.
Page 9
NAN 02/14
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
6
F
F
G
Step Eleven
Attach back panel (6) onto back side of the unit using 30x nails (F), with the help of the nail guide (G).1.

Important:
Two people are
needed here
HH
HH
HH
Z2
Z2
Z2
Z1
Z1
Z1
Page 10
Step by step assembly instructi ns
Step Twelve
With help of an assistant, carefully stand up the unit upright1.
Step Thirteen
Fix runner parts (Z1) (Z2) through holes shown in the detail view
using euroscrews (H).
1.
NAN 02/14

Important:
Take care when
drilling the wall
that you do not
drill into any
pipes, wires etc.
If in doubt, consult
an expert.
wall plug and
screw not
included.
O
N
O
I
Page 11
NAN 02/14
Step by step assembly instructi ns
Step Fourteen
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall
by use “L” Bracket (N) fitted to the Top of the unit.
Loosen the screw (I) and fix “L” bracket (N) to the wall using spacer (O) and appropriate wall plug and
screw (not included)
Tighten Screw (I)
See wall fixings guide at the end of booklet.
1.
2.

13
16
15
E
E
D
A
D
16
15
14
L
L
Step by step assembly instructi ns
Step Fifteen
Attach 4x wooden dowels (E) into the pre drilled holes on drawer sides (15) (16) as shown,
Place the cam lock (D) into the holes on drawer sides (15) (16) as shown,
arrow pointing towards the bolt,
Attach 2x metal dowels (A) into the pre drilled holes on drawer front (13). Use a screwdriver to
turn fitting (A) clockwise to fix
1.
2.
3.
Step Si teen
Fit the RH (15) and LH (16) drawer sides to the drawer back (14) using 30 mm screws (L), 1.
Page 12
NAN 02/14

Page 13
NAN 02/14
13
2
D
1
D
A
9
12
11
8
E
D
D
A
A
D
E
Step by step assembly instructi ns
Step Seventeen
Slide drawer bottom panel (9) into the drawer box grooves.
Position drawer front (13) onto drawer box, turn locking nuts (D) clockwise to lock.
1.
2.
Step Eighteen
Attach 4x wooden dowels (E) into the pre drilled holes on drawer sides (11) (12) as shown.
Place the cam lock (D) into the holes on drawer sides (11) (12) as shown
arrow pointing towards the bolt,
Attach 4x metal dowels (A) into the pre drilled holes on drawer front (8).
Use a screwdriver to turn fitting (A) clockwise to fix.
Repeat for the second drawer.
1.
2.
3.

Page 14
NAN 02/14
15
14
16
L
L
2
D
1
D
A
8
9
Step by step assembly instructi ns
Step Nineteen
Fit the RH (14) and LH (15) drawer sides to the drawer back (16) using 30 mm screws (L),
Repeat for the second drawer.
1.
Step Twenty
Slide drawer bottom panel (9) into the drawer box grooves,
Position drawer front (8) onto drawer box, turn locking nuts (D) clockwise to lock.
Repeat for the second drawer.
1.

Page 15
NAN 02/14
Step by step assembly instructi ns
Step Twenty-one
Pull out the runners, then ensure plastic securing pegs are to the OUT position.1.

245
245
165
Step Twenty-two
Slide the drawer box tilted until the stop.
Attach the drawer box leaning on the runners.
Push the plastic securing pegs in the IN position
1.
2.
3.
Page 16
Step by step assembly instructi ns
NAN 02/14

Page 17
NAN 02/14
Step by step assembly instructi ns
Step Twenty-three
Use the small plastic knob of the runners to align the drawers if needed.1.

Page 18
NAN 02/14
Wood
If xing to wood
make sure that it
isn't chipboard as
screws can easily
pull away from the
core structure
Brick or Masonry
Use an appropriate
wall plug provided you
are sure your wall is
sound.
Cavity wall
Special toggle
wall plugs are
needed. Seek
expert advice.
Wall fixing - if in d ubt seek pr fessi nal advice
Care and Maintenance
his product has been manufactured using modern manufacturing methods and materials.
o keep your product, looking at its best, we strongly recommend either dusting with a soft cloth, or
the use of a damp (not wet ) cloth and water containing no more than a 5% soap solution.
Dry with a soft clean cloth.
Aggressive chemicals, such as wax furniture polish, abrasive cleaners, bleach or hypochlorate (chlorine)
based cleaners, multi purpose cleaners, dilutes, acetone, alcohol and solvent based liquid product should
NO be used, as may result in damage.

Page 19
BRY 02/13
Safety Instructi ns
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten when necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No
liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
It is recommended that before moving a heavy object to a new location it is completely dis-assembled to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
his product is designed to be fixed securely to a sound wall in the manner stated.
It must under no circumstances be used free-standing. No liability will be accepted for damage or injury caused by
inadequate fixing or use without fixing.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SWIE 5NN
www.johnlewis.com