John Thomas T-4268XBT User manual

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 1 - THIS ITEM IS PACKED IN 2 CARTON
ASSEMBLY INSTRUCTIONS
Description
Item No
: DOUBLE BUTTERFLY LEAF TABLE
: T-4268XBT AND T-4268XBB

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 2 - THIS ITEM IS PACKED IN 2 CARTON
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART LIST T-4268XBT
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1
PART LIST T-4268XBB
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
B Pedestal 2 C Leg 4
D Crossbar 1
BEFORE ASSEMBLY

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 3 - THIS ITEM IS PACKED IN 2 CARTON
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Hexagon nut
(8X13mm) 20
2 Flat washer
(8.5x19 mm) 20
3 Lock washer
(8.5x13 mm) 20
4
Wrench
(M13mm) 1
5 Allen key
(4x80mm) 1
NOTE: HARDWARE IS PACKED IN CARTON T-4268XBB
STEP 1
Attach crossbar (D) and legs (C) to pedestals (B) with nuts (1), and washers (2) and (3) as shown
below. Tighten with the wrench (4).

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 4 - THIS ITEM IS PACKED IN 2 CARTON
STEP 2
Use the Allen key (5) to loosen the bolts and washers, and remove the plates underneath the table
top.
STEP 3
Place the plates on top of the pedestal (B), attach with washers (6) and (2) and nuts (3). Tighten with
the Wrench (4) as shown below.
B

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 5 - THIS ITEM IS PACKED IN 2 CARTON
STEP 4
Carefully put the pedestal block on the bottom side of the table top, attach the top to plate with
bolts and washers (from step 2) and tighten with the Allen key (5).

ITEM NO. : T-4268XBT AND T-4268XBB
REVISED FEB 04, 2015
Printed in Vietnam
- 6 - THIS ITEM IS PACKED IN 2 CARTON
STEP 5
Unlock the table top from both sides underneath the table top. Pull the 2 parts of the top apart.
Place the leaves in the center of the open table top. Push the table top closed.
STEP 6
Place the leaf in the center of the open table top. Push the table top closed. Lock the mechanism
underneath 2 sides of the table top as shown below.