John Thomas TV-51 User manual

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:
STURBRIDGE TV
CENTER
: TV-51

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 3 -
PART
LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1 F Vertical panel
(L-R) 2
B Center
panel 1
G Center shelf 1
C Door (L-R) 2 H Side shelf
(L&R) 2
D Side panel 2
I
Back panel
1
E Bottom
panel 1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Short bolt
(M6x30mm) 4
7
Door pin
(5.2/13x1.2mm)
(7x10mm) 4
2 Long bolt
(M6x35mm) 16
8 Allen key
(4x80mm) 1
3 Spring washer
(6.5X11mm) 16
9 Screw
(M3x15mm) 26
4 Flat Washer
(6.5X19mm) 16
10 Screw
(M3x15mm) 16
5 Knob
(38x30mm) 2
11 Magnet 2
6 Pan head screw
(M4 x 30mm) 2
12 Bracket 12

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 4 -
STEP 1
Attach panels (F) to panels (B) with bolts (1), washers (3) and (4) as shown below. Tighten with Allen
key (8).
Attach panels (F) to bottom panels (E) with bolts (2). Tighten with Allen key (8).
Attach doors (C) to panels (B) and (E) with door pins (7).
Attach magnets (11) to panels (F) with screws (10) as shown below. Tighten with a screwdriver.

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 5 -
STEP 2
Attach side panels (D) to the unit and Top (A) with bolts (2), washers (3) and (4) as shown below.
Tighten with Allen key (8).
STEP
3
Attach back panel (I) to the unit with screws (9). Tighten with the screwdriver.
STEP 4

ITEM
NO.
:
TV
-
51
RE
VISED AUG 2
2
, 2014
Printed in V
ietnam
- 6 -
ST
EP
4
Attach brackets (12) to panels (F) and (D). Place the shelves (G) and (H) on the brackets and attach
with screws (10).
Attach knobs (5) to doors (C) with screws (6). Tighten with the screwdriver.