John Thomas SH-7247X User manual

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: X-SIDE ROOM DIVIDER 72 H X 47 W
: SH-7247X

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1
B Side frame 2
C Center
frame 1 D Bottom Shelf 1
E Shelf 6 F Leg
(L-R) 4
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 bolt
(M6x35mm) 34
2 Flat Washer
(M6.5x13mm) 34
3 Lock Washer
(M6.5x11mm) 34 4 Long Screw (M4x45mm) 16
5 Long Screw
(M4x30mm) 4
6 Allen Key
(4x80mm) 1
7
Screw
(M3.5x15mm) 4 8 Steel band 2
STEP 1
Attach shelves (E) to the side frames (B) with bolts (1), and washers (3) and (2) as shown below.
Tighten with Allen key (6).

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 4 -
STEP 2
Attach shelves (E) to the center frames (C) with bolts (1), and washers (3) and (2) as shown below.
Tighten with Allen key (6).
STEP 3
Attach shelves (E) to the center frames (C) with bolts (1), and washers (3) and (2) as shown below.
Tighten with Allen key (6).

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 5 -
STEP 4
Attach shelves (E) to side frames (B) with bolts (1), and washers (3) and (2) as shown below. Tighten
with Allen key (6).
STEP 5
Attach the top (A) to the unit with bolts (1), and washers (3) and (2), as shown below. Tighten with
Alen key( 6).

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 6 -
STEP 6
Attach the top (A) to the unit with screws (5). Tighten with a screwdriver
Attach the Bottom Shelf (D) to the unit with bolts (1), and washers (3) and (2). Tighten with Alen key
( 6).
STEP 7
Attach the legs (F) to the unit with screws (4) as shown below. Tighten with a screwdriver.
A

ITEM NO : SH-7247X
REVISED MAY 08, 2015
Printed in Vietnam
- 7 -
STEP 8
Attach steel bands (8) to the unit with screws (7) and attach steel bands (8) to the wall with screws (5)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.