JVA Z14 User manual

Z14 Quick Start Guide
JVA TECHNOLOGIES
www.jva-fence.com

Z14/R Programming Reference
Whilst the system defaults are sucient for basic installations, greater versatility can be achieved via the Z14/R programming
options. To program the Z14/R you must have a keypad connected and the unit turned on but not ring. For more information
about connecting a keypad please refer to the Z14/R Manual.
Changing the programming options
First you have to enter Programming mode.
Command Key 1 Key 2 Key 3 Key 4 Key 5 Key 6 Key 7 Key 8 Key 9
Enter Programming Mode Installer Pin (Default: 012345) * 0 #
When you have entered Programming mode you can begin to use the following options to congure your Z14/R Security
Energiser. Default Values are highlighted in grey.
Command Key1 Key2 Keys 3 and 4 Key5
Change The Installer PIN
6 Digits
0 0 Enter the new 6 digit Installer PIN #
High Power Mode Power
Level
0 1 0 0 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 #
Output Voltage (kV) Conventional
5.0 5.5 6.0 6.5 7. 0 7. 5 8.0 8.5 9.0 9.5
Output Voltage (kV) Bi-Polar
2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.5
Low Power Mode Power
Level
0 2 00 01 02 03 04 05 06 07 08 09 #
Percentage of High Power Mode Power Level
0.5% 1.0% 1.5% 2.0% 2.5% 3.0% 3.5% 4.0% 4.5% 5.0%
Return Fence Alarm
Voltage For High Power
Mode
0 3 00 01 02 03 04 05 06 07 08 09 #
Fence Alarm Voltage (kV) Conventional
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Fence Alarm Voltage (kV) Bi-Polar
1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2
Return Fence Alarm Volt-
age For Low Power Mode
0 5 00 01 02 03 04 #
300 Volts 500 Volts 700 Volts 900 Volts 110 0 Vo l ts
Bad/Missed Pulse Count
Before Alarm Triggers
0 6 00 01 02 03 04 05 06 07 08 09 #
0123456789
Battery Alarm
Voltage(volts). Alarm
Value Shown, Reduced
Power is 1V less
0 7 00 01 02 03 04 05 06 07 08 09 #
9.0 9.5 10.0 10.5 11. 0 11. 5 12.0 12.5 13.0 13.5
Siren On Time
(S=Seconds, M=Minutes)
0 8 00 01 02 03 04 05 06 07 08 09 #
10S 30S 1M 2M 3M 4M 5M 20M 45M 130M
Siren O Time
(S=Seconds, M=Minutes)
0 9 00 01 02 03 04 05 06 07 08 09 #
10S 1M 2M 5M 10M 20M 30M 40M 50M 60M
Siren Cycles 1 0 00 01 02 03 04 05 06 07 08 09 #
0123456789
Input Type 1 1 00 01 #
Normally Open (NO) Normally Closed (NC)
Input 2 Function 1 2 00 01 #
Gate Low Power

Command Key1 Key2 Keys 3 and 4 Key5
Gate Entry/Exit Delay
(S=Seconds, M=Minutes)
1 3 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M 8M
Chime Mode 1 4 01 02 03 04 05 #
None Door Chime Siren Fence Alarm Gate Beeps
Plus Siren
Combined Options 1
(add up the options you
want. e.g. for Max Power
and Limit output:
2 + 4 = 6 Therefore enter
06 for keys 3 and 4
1 6 +2 +4 +8 +16 +32 #
Maximum
Power at all
times
Limits out-
put to 2.5J
per Zone
Enables IR
Tamper.
Stop slaves
on comms
fail
Stop Ener-
giser send-
ing alarm
memory
Anti Bridging threshold 1 7 Enter in the percentage dierence required to trigger the Anti-Bridging
alarm. e.g. if you require a 10% change in return voltage to trigger the
alarm, enter 10 for keys 3 and 4
#
Combined Options 2
(like Combined Options 1)
1 8 +1 +2 +4 +8 #
Siren Codes
(Chirps 1 for
armed, twice for
disarmed)
Gate Delay Type 4800 baud 9600 baud
Auto Re-arm Time
(S=Seconds, M = Minutes,
D=Disabled
2 0 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M D
Relay 1 2 1 Options Explained under “1.1.1 Relay Functions” Default is 08 #
Relay 2 2 2 Options Explained under “1.1.1 Relay Functions” Default is 09 #
Relay 3 (Fitted Z14R only) 2 3 Options Explained under “1.1.1 Relay Functions” Default is 00 #
Relay 4 (Fitted Z14R only) 2 4 Options Explained under “1.1.1 Relay Functions” Default is 02 #
Relay 5 (Fitted Z14R only) 2 5 Options Explained under “1.1.1 Relay Functions” Default is 07 #
Group Mode 2 6 00 01 02 etc 15 #
No Group Master Slave 1 Slave 14
Exit Programming Mode * #
Relay Functions
The table below is for use for the relay programming options mentioned in the table on the previous page.
Keys 3
and 4
Funtion Description
00 Fence Triggers when Zone 1 is Armed and Return Voltage is below the Threshold voltage
01 Fence or O Triggers when Zone 1 is Disarmed or Return Voltage is below the Threshold vVoltage
02 Armed Zone 1 is Armed
06 Fence Bi-Polar Triggers when energiser is Armed and the Fence Return Voltage on either Bi-Polar return line
has fallen below the Threshold Voltage
07 General Triggers on AC Fail, Tamper, Low Battery/Bad Battery, Gate Alarm or Internal error. Latched
(internal errors only)
08 Siren Triggers on Fence Alarm , Gate or Tamper. Will time out after the Siren Time Out time. Latched
09 Strobe Triggers on Fence Alarm, Gate or Tamper. Only turns o on Energiser Aisarm. Latched
10 AC Fail Triggers on AC Fail
11 Low/Bad Battery Triggers on low or bad battery
12 Tamper Triggers when the case has been opened and J3 has been tted (Z14R only)
14 Gate Triggers on Gate Alarm
15 Siren Caused by
Gate
Behaves like siren, only for Gate Alarm
16 Armed - Low
Power Mode
Triggers when Armed in Low Power mode
17 Group Armed Triggers when group is armed. Only congurable on group master.
18 Group general Triggers on group general alarm. Only congurable on group master.

www.jva-fence.com
DEALER
ThE JVA Logo is ATRADEmARk of JVA TEchnoLogiEs PTy LTD
© JVA TEchnoLogiEs PTy LTD