1
KD-R826BT
Installation/Connection Manual
/
0111DTSMDTJEIN
EN, TH
© 2011 Victor Company of Japan, Limited
GET0716-005A
[U/UH]
Bracket / *
Pocket /
Flat head screws (M5 × 8 mm) / (M5 × 8 mm) *
INSTALLATION /
When installing the unit without using the sleeve /
In-dash mounting / In-dash
WARNINGS /
Removing the unit /
Do the required electrical connections. /
Bend the appropriate tabs to hold the sleeve
firmly in place. /
Install the unit at an angle
of less than 30˚. /
30˚
*Not supplied for this unit.
*
• You need the installation kits which corresponds to your car.
• If you have any questions or require information regarding installation kits, consult your JVC car audio
dealer or a company supplying kits.
• The unit can only be installed in a car with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise,
change
the
<Amplifier
Gain>
setting.
(See
page
24
of
the
INSTRUCTIONS.)
• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not
remove the caps on the ends of the unconnected wires or the terminals.
• If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old
fuse with one that has the same rating.
• Install this unit in the console of your vehicle.
• Mount the unit so that the mounting angle is 30° or less.
• Be sure to ground this unit to the car's chassis again after installation.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working
properly.
• Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the
heat sink and enclosure become hot.
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
ENGLISH /
• The fuse blows.
]
Are the red and black leads connected correctly?
• Power cannot be turned on.
]
Is the yellow lead connected?
• No sound from the speakers.
]
Is the speaker output lead short-circuited?
• Sound is distorted.
]
Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
]
Is the rear ground terminal connected to the car’s chassis using shorter
and thicker cords?
• This unit becomes hot.
]
Is the speaker output lead grounded? ; Are the “–” terminals of L and R
speakers grounded in common?
• This unit does not work at all.
]
Have you reset your unit?
TROUBLESHOOTING /
•
•JVC
• DC 12 V
•
• 50 W ( 4 Ω 8 Ω) <Amplifier Gain>
( 24 )
•
•
•
• 30°
•
•
•
•
•
Part list /
A
Hard case / (×1)
B
Control panel / (×1)
C
Sleeve / (×1)
D
Trim plate / (×1)
E
Power cord / (×1)
F
Handles / (×2)
G
Microphone / (×1)
H
Microphone clips /
(×2)
I
KS-UBT1: USB Bluetooth Adapter /
USB (×1)
Release the rear section first... /
...
•
]
?
•
]
?
•
]
?
•
]
? ; “–” L () R ()
?
•
]
?
•
]
? ; “–” L () R ()
?
•
]
?
Install_KD-R826BT_005A_f.indd 1Install_KD-R826BT_005A_f.indd 1 1/17/11 4:55:30 PM1/17/11 4:55:30 PM
