JWA GUZMAN 75864 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
75864
BEDSIDE
GUZMAN
ITEM CODE
500MM
450MM
550MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lng. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not ovghten the screws and bolts as this may damage the threads
Allow 40 min For 2 person Addonal tools required
2

PARTS LIST
3
1
10
2
3
4
5
6
7
8
9
11
11
12 13
12

4
NO. ITEM QTY NO. ITEM QTY
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
31 PC
1 PC
41 PC
51 PC
1 PC
1 PC
1 PC
PARTS LIST
2
61 PC
1 PC
2 PCE
10
11
LEFT SIDE PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
BACK PANEL
A8PCS
B8PCS
C8PCS
D4PCS
E1PC
F4PCS
10PCS
J
4PCS
K
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ5*35
G4PCS
H4PCS
Φ3*12
Φ4*35
L
DRAWER FRONT PANEL
7DRAWER LEFT SIDE PANEL
DRAWER RIGHT SIDE PANEL
DRAWER BACK PANEL
DRAWER BOTTOM PANEL
BOTTOM SUPPORT METAL
10PCS
2 PCE
12
Φ6*40
1PC
M
12PCS
N
8
9
1 PC
13
METAL LEG
1PC
I
Φ3*16
CL
DL
CR
DR
1PC
O
BOTTOM SUPPORT METAL

STEP 1:
STEP 2:
5
A X4
1
A
N X6
A
A
A
A
O X1
2
3
O(CL)
O(CR)
NN N
NNN

STEP 3:
STEP 4:
6
C X4
2
D
D X4
3
4
D
D
D
C
C
C
C
23
5
4

STEP 5:
STEP 6:
7
1
C
K X6
C X4B X4
23
C
C
C
BB
B
B
J X6
I X1
3
2
4
13
11
11
I
J
J
J
J
J
J
K
KKK
KK

STEP 7:
STEP 8:
8
2
I
L X4
K X4
J X4
I X1
3
4
12 12
J
J
J
J
KK
K
K
I X1
43
I
L
L
L
L

STEP 9:
STEP 10:
9
A X4
6
A
N X6
B X4F X4M X1
6
7
7
7
88
8
9
9
9
10
A
B
B
B
B
F
F
M
M
O X1
6
8
O(DL)
O(DR)
NN
N
N
NN

STEP 11:
STEP 12:
10
6
G
H X4
G X4
12
2
5
G
G
G
G
G
H
H
H

STEP 13:
11
E X1
E
CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs To Bend/Break.
ASSEMBLY IS COMPLETE
WALL E
E
E
E

12
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
13