JWA GATES 75251 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
75251/75254
TALL CHEST
GATES
ITEM CODE
850MM
450MM
1150MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lng. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 45 min For 2 person Addinal tools required
2

PARTS LIST
3
1
23
4
55
6
6
6
77
8
8
9
10
10
11
11
12
12
13
14
X2
X2
15
15
16
9

4
NO. ITEM QTY NO. ITEM QTY
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
52 PCE
2 PCE
4 PCE
4 PCE
4 PCE
10
4 PCE
PARTS LIST
2
8
9
11
12
63 PCE
72 PCE
2 PCE
2 PCE
13
14
LEFT SIDE PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
BACK PANEL
CROSSING BAR
LEG
LEG
DRAWER LEFT SIDE PANEL
DRAWER RIGHT SIDE PANEL
DRAWER BACK PANEL
DRAWER BOTTOM PANEL
DRAWER FRONT PANEL
DRAWER FRONT PANEL
4 PCE
1 PC
15
16
BOTTOM SUPPORT PANEL
MIDDLE SUPPORT PANEL
A56PCS
B56PCS
C16PCS
D4PCS
E2PCS
F20PCS
16PCS
I
4PCS
J
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ3*16
G48PCS
H16PCS
Φ3*12
Φ4*35
CL
CR
DR
DL

STEP 1:
STEP 2:
5
A X6
1
J X4
G X24
A X12
A
AA A A
A
2 3
AA
AA
AAA
A
AA
AA
GGG
GGG
GGG
G G G
GGG
GGG
GG
G
GGG
J(CL)
J(CL)
J(CL)
J(CL) J(CR)
J(CR)
J(CR)
J(CR)

STEP 3:
STEP 4:
6
B X12
6
B
A
7
A X8
7
6
6
23
B
B
B
B
B
B
A
A
A
A

STEP 5:
STEP 6:
7
B X8
8
B
8
7
7
B
B
B
B
A X8
4
A
A
A
A
AA
AA

STEP 7:
STEP 8:
8
B X8
8
B
A X2
C X8
8
4
7
7
B
B
C
C
C
CC
CC
B
4
A

STEP 9:
STEP 10:
9
C X4
4
C
B X2
D X4
3
2
C
D
DD
D
3
216
BB
B

STEP 11:
STEP 12:
10
C X4
3
C
2
55
B X6
C
BB
BBB
2
3
1

STEP 13:
STEP 14:
11
B X10A X10F X10
9
99
10
10 10
11
11
15
11
13
13
X2
12
F
F
F
A
AAA
B
B
B
B X10A X10F X10
910
X2
B
10
10
14
14
11
11
11
12
15
9
9
B
B
AAA
AF
F
F

STEP 15:
STEP 16:
12
G X12J X2
G X12J X2
13
9
10
J(DL)
J(DR)
G
G
G
GG
G
X2
10
J(DR)
J(DL)
9
G
G
G
G
GG
14
X2

STEP 17:
STEP 18:
13
H X16
14
14
13
13
I X16
12
2
II
II
III
I
I
II
II
I
I
II
H
H
H
H
H
HH
HH
H
H
H
H
HH
H
H
H

STEP 19:
14
ASSEMBLY IS COMPLETE
CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs To Bend/Break.
E X2
E
WALL
E
E
E
EE
E
EE
E

15
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
16