JWA HARDING 74704 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
74704
2 DRAWER BEDSIDE
HARDING
ITEM CODE
480MM
400MM
480MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addional tools required
2

PARTS LIST
3
1
2
3
4
5
6
67
7
8
8
9
10
11
12
13
14
X2

4
NO. ITEM QTY NO. ITEM QTY
A12PCS
B12PCS
C8PCS
D4PCS
E1PC
F4PCS
I
2PCS
K
L2PCS
M2PCS
N
2PCS
J
2PCS
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ3*16
PARTS LIST
Φ3*12
G4PCS
H24PCS
1PC
O8PCS
Φ5*30
P8PCS
Φ6*30
Φ3.5*12
Q4PCS
R8PCS
S8PCS
Φ4*35

5
NO. ITEM QTY NO. ITEM QTY
PARTS LIST
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
51 PC
2 PCE
2 PCE
2 PCE
2 PCE
2 PCE
2LEFT SIDE PANEL
12
8
9
RIGHT SIDE PANEL
BOTTOM PANEL
62 PCE
72 PCE
1 PC
13
1 PC
14
BACK PANEL
METAL LEG
10
11
METAL LEG
METAL LEG
DRAWER BOTTOM PANEL
DRAWER LEFT SIDE PANEL
DRAWER BACK PANEL
DRAWER RIGHT SIDE PANEL
DRAWER FRONT PANEL
DRAWER FRONT PANEL

STEP 1:
STEP 2:
6
A X4
1
A
H X12
A
A
A
J X2I X2
2
3
I
I
J
J
H
H
H
H
H
H
H
H
H
H
H
H

STEP 3:
STEP 4:
7
C X4
1
B
B X4
2
3
B
B
B
C
C
2
5

STEP 5:
STEP 6:
8
D
C X4
2
P X8
D X4
34
D
D
D
C
C
6
6
N X1
N
P
PP
P
P
P
P
7
7
8
8

STEP 7:
STEP 8:
9
R X8N X1O X8
4
N
O
O
O
O
O
O
O
O
R
R
R
R
R
R
R
2
F X4G X4
2
5
G
G
F
F
GG
G
F
FF
F

STEP 9:
STEP 10:
10
A X4B X4S X4M X1Q X2
A X4B X4S X4M X1Q X2
9
A13
13
10
10
10
12
12
12
11
11
11
9
A
B
B
M
Q
S
S
14
14
9
9
12
12
12
10
10
10
11
11
11
M
Q
A
A
S
S
B
B

STEP 11:
STEP 12:
11
H X6L X1K X1
K
14
12
L
H
H
H
H
H
H
H X6L X1K X1
13
12
H
H
H
H
H
H
L
K

STEP 13:
12
14
STEP 14:
13
E X1
E
E
E
WALL EE
E

ASSEMBLY IS COMPLETE
13

14
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
15