JWA MYERS 76441 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
6 DRAWER DRESSER
MYERS
ITEM CODE 76441
1492mm
818mm
400mm

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lg. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not ovghten the screws and bolts as this may damage the threads
Allow 45 min For person Addnal tools required
2
2

PARTS LIST
3
x4
x2
10
11
12
13
15
14
19
15
17
16 18
13
9
9
9
1
2
3
6
4
5
5
7
7
8
8
9

4
NO. ITEM QTY NO. ITEM QTY
A58PCS
58PCS
32PCS
6PCS
60PCS
6PCS 2PCS
30PCS
12PCS
6PCS
8PCS
8PCS
B
C
13
9
PARTS LIST
D
E
F
H
G
I
J
K
L
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
BACK PANEL
MIDDLE PANEL
NO. ITEM QTY NO. ITEM QTY
11 PC
3
1 PC
41 PC
1 PC
52 PCS
2 PCS
2 PCS
6
1 PC
7
8
15
14
10
12
11
16
18
17
4 PCS
4 PCS
4 PCS
6 PCS
4 PCS
4 PCS
6 PCS
2 PCS
2 PCS
2 PCS
19 2 PCS
2
TOP PANEL
DRAWER FRONT
DRAWER LEFT
PANEL
DRAWER FRONT
PANEL
PANEL
PANEL
PANEL
PANEL
DRAWER RIGHT
DRAWER LEFT
PANEL
PANEL
DRAWER RIGHT
DRAWER BACK
LEG
LEG
PANEL
PANEL
DRAWER BACK
DRAWER SUPPORT
DRAWER BOTTOM
CROSSING BAR
(CL) (DL) (DR) (CR)
4x35mm
3x12mm
4x30mm
4x16mm
3x16mm

STEP 1:
STEP 2:
5
8xB 8xC
36xE6xF
8xA
E
E
E
E
E
E
E
EE
EE
EE
E
E
E
E
EE
E
E
E
E
EE
E
E
F
F
F
F
F
F
F
F
F
F
F
F
E
E
E
E
E
E
E
E
E
(CL)
(CL)
(CL)
(CL)
(CL)
(CL)
(CR)
(CR)
(CR)
(CR)
(CR)
(CR)
34
6
6
E
F
E
F
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
CC
C
C
C
9
9
9
9
3
6
4

STEP 3:
STEP 4:
6
6xC 6xD
4xA 4xB 4xC
C
C
C
C
C
C
D
D
D
D
D
D
2
3
4
A
A
A
A
B
B
B
B
C
C
C
C
7
7
8
8

STEP 5:
STEP 6:
7
10xA 10xB 8xC
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
2
3
4
7
7
8
8
3
4
5
5

STEP 7:
STEP 8:
8
10xG
6xB6xA 6xC
x2
A
A
B
B
B
B
C
B
B
A
A
C
A
A
C
1
3
4
G
G
G
G
G
15
17
16
18
13

STEP 9：
STEP 10:
9
20xG
10xB10xA 2xI 4xH8xE2xF
x2
x4
(DL)
(DR)
A
A
A
AA
B
BB
B
B
E
E
E
E
F
F
I
H
x2
19
G
G
G
G
G
10
11
12
13
15

STEP 11:
STEP 12:
10
20xB20xA 4xI 8xH
16xE 4xF
x4
x4
(DL)
(DR)
E
E
E
E
F
F
x4
A
A
A
A
A
B
B
B
BBI
H
14

11
STEP 13:
STEP 14:
8xK8xJ
14
14
19
14
14
19
J
J
K
K
J
J
K
K
J
J
K
K
J
J
K
K
1
2

12
STEP 15:
2xL
L
L
L
L
L
L

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
HARDWARE
Wall Back side
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1 washer X2

To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14