Jytek Pxi-63980 User manual

PXI-63980

PXI Embedded Controller

User’s Manual

Manual Rev.: 1.00

Revision Date: JUL.16, 2016

I

Getting Service

Contact us should you require any service or assistance.

SHANGHAI JYTEK Co., Ltd.

Web site: hp://www.jytek.com

Address: (201203) 300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong New Area,

Shanghai, 201203 China

Tel: +86-21-5047-5899

Fax: +86-21-5047-5899

Email: [email protected]

Addional informaon, aids, and ps that help users perform tasks

Informaon to prevent minor physical injury, component damage, data loss,

and/or program corrupon when trying to complete a task.

Informaon to prevent serious physical injury, component damage, data loss,and/

or program corrupon when trying to complete a specic task.

II

Table of Contents

Geng Service �� I

1 Introducon�� 1

1�1 Features �� 2

1.2 Specicaons �� 3

2 Geng Started�� 6

2�1 Package Contents �� 6

2.2 Operang System Installaon�� 6

2.3 Hardware Instrucons �� 7

2�3�1 Faceplate Connectors & Indicators �� 7

2�3�2 PXI Trigger Connector�� 9

2�3�3 DVI-I Connector�� 9

2�3�4 GPIB Connector��10

2.3.5 Reset Buon ��11

2�3�6 LED Indicators ��11

2�3�7 USB 2�0 Ports ��12

2�3�8 Gigabit Ethernet Ports ��13

2�3�9 USB 3�0 Ports ��13

2.3.10 Onboard Connecons and Sengs��13

2.3.11 Installaon Environment ��14

2�3�12 Installing the PXI-63980��15

2�3�13 Replacing the Hard Drive or Solid State Drive ��15

2.3.14 Replacing the Baery Backup ��16

2�3�15 Clearing CMOS ��16

2.3.16 Iniang Backup BIOS Flash ��17

3 Driver Installaon ��18

3�1 Installing Windows Drivers ��18

3�2 Installing the Chipset Driver��18

3�3 Installing the Graphics Driver��19

3�4 Installing the Ethernet Driver��19

3�5 Installing the GPIB Driver��19

3.6 Installing the Management Engine Driver ��20

3�7 Installing the PXI Trigger Driver��20

3�8 Installing the WDT Driver��20

3�9 Installing the USB 3�0 Driver ��21

4 BIOS Setup ��22

4.1 Starng the BIOS��22

4�2 Main Setup��23

4�3 Advanced Setup ��24

4.4 Chipset Conguraon ��25

4�5 Boot Setup ��25

III

4.6 Security Setup ��25

4�7 Save & Exit Setup ��26

Appendix A - PXI Trigger I/O Funcon Reference��27

A.1 Data Types ��27

A.2 Funcon Library��28

A�2�1 TRIG_Init ��28

A�2�2 TRIG_Close ��28

A.2.3 TRIG_SetSoTrg��29

A�2�4 TRIG_Trigger_Route ��29

A�2�5 TRIG_Trigger_Clear ��31

A.2.6 TRIG_GetSoTrg ��31

A.2.7 TRIG_Trigger_Route_Query��32

A�2�8 TRIG_GetDriverRevision��33

Appendix B - Watchdog Timer ��35

B.1 WDT Funcon Library��35

B�1�1 InitWDT ��35

B�1�2 SetWDT��35

B�1�3 StartWDT ��36

B�1�4 ResetWDT ��36

B�1�5 StopWDT��37

Important Safety Instrucons ��38

IV

List of Tables

Table 2-1: DVI-I Pin Assignment ��10

Table 2-2: GPIB Pin Descripon ��11

Table 2-3: LED Indicator Legend ��11

Table 2-4: USB 2.0 Port Pin Assignment��12

Table 2-5: PXI-63980 Ethernet Port Pin Assignments ��13

Table 4-1: BIOS Hot Key Funcons��23

Table 4-2: BIOS Main Setup Menu��24

Table 4-3: BIOS Advanced Setup Menu ��24

Table 4-4: BIOS Chipset Conguraon Menu ��25

Table 4-5: BIOS Boot Setup Menu ��25

Table 4-6: BIOS Security Setup Menu ��25

V

List of Figures

Figure 1-1: PXI-63980 Funconal Block Diagram �� 3

Figure 2-1: PXI-63980 Faceplate�� 7

Figure 2-2: PXI Trigger SMB Jack�� 9

Figure 2-3: PXI-63980 LED Indicators��11

Figure 2-4: PXI-63980 Onboard Conguraon ��14

Figure 4-1: BIOS Setup Navigaon��23

1

1 Introduction

The JYTEK PXI-63980 PXI™ embedded controller, based on the Intel® Core™ i7 processor,

is specically designed for PXIbased tesng systems, providing a rugged and stable

operang environment for a wide variety of tesng and measurement applicaons.

Combining state-of-the-art Intel® Core™ i7-2715QE 2.1 GHz processors, and up to 16 GB

of 1333 MHz DDR3 memory, the PXI-63980 ulizes four separate compung engines

on a single processor, enabling execuon of four independent tasks simultaneously in a

multasking environment.

PXI-based tesng systems typically make up a PXI plaorm and diversied standalone

instruments for complex tesng tasks. The PXI-63980 provides ample interface

choices, including GPIB, USB2.0, and USB3.0, for connecng and controlling instruments.

The PXI-63980 also provides dual Gigabit Ethernet ports, one for LAN connecon and the

other for controlling LXI instruments. With exible instrument control interfaces and

mechanical and electronic reliability, the JYTEK PXI-63980 is more than equal to the

challenges of the most demanding PXI-based tesng systems

Memory addressing over 4GB is OS-dependent, such that a 32-bit operang system

may be unable to address memory space over 4GB. To fully ulize memory, 64-bit

operang systems are required.

2

1�1 Features

• PXI™-1 PXI Hardware Specicaon Rev.2.2 complaint

• Intel® Core™ i7-2715QE 2.1 GHz processor for maximum compung power, 3.0GHz

maximum in single-core, Turbo Boost mode.

• Dual Channel DDR3 SODIMM

• Up to 16 GB 1333 MHz

• Maximum system throughput 132 MB/s

• Pre-installed 500 GB SATA hard drive

• Supports 2.5" HDD or SSD

• SATA 3.0 Gb/s

• Supports AHCI

• Integrated I/O

◦ Dual Gigabit Ethernet ports

◦ Four USB 2.0 Ports

◦ Built-in GPIB (IEEE488) controller

◦ DVI-I video connector

◦ Two USB 3.0 Ports

◦ Trigger I/O for advanced PXI™ trigger funcons

• Programmable watchdog mer

3

1�2 Specifications

Channel B

204 pin SODIMM

Channel A

204 pin SODIMM

Front Panel

Connectors

Intel® QM67

Express Chipset

Intel® Core™

i7-2715QE 2.1GHz

Processor

PCIe x1

GbE

connectorGbE I/F

USB

connector x4

GPIB controllerUSB2.0

GPIB

connectorGPIB

SMB

Connector

PXI Connector

Trigger Bus

Controller

USB3.0

connector x2

PCIe-to-PCI

bridge

2.5" SATA HDD

SATA

GbE

connectorGbE I/F

Digital

Display I/F

DVI

DVI-I

connector

PCIe x1

DVI level shifter

Trigger Signal

SMBUS

Intel FDI DMI

GbE PHY

82579LM

GbE controller

I210

Trigger Bus

PCI

DDR3

1333MHz

DDR3

1333MHz

USB 2.0

PCIe x1USB3.0 PCIe-to-USB3.0

PCIe x1

Figure 1-1: PXI-63980 Functional Block Diagram

Processor

• Intel® Core™ i7-2715QE 2.1GHz processor, 3.0GHz maximum in single-core, Turbo

Boost mode

• DMI (Direct Media Interface) with 5 GT/s of bandwidth in each direcon

Chipset

Mobile Intel® QM67 Express

Memory

• Two standard 204-pin DDR3 SODIMM sockets

• Support for +1.5 V DDR3, 1066/1333 MHz RAM up to 16 GB total

• Support for non-ECC unbuered memory

The externally accessible SODIMM socket can accept replacement DDR3 DRAM

DIMM modules.

PXI-63980 specicaons and stability guarantees are only supported when JYTEK-

provided DDR3 DRAM DIMM modules are used.

4

Video

• DVI output supporng up to 1920x 1200 @ 60 Hz resoluon

• VGA output for analog CRT route to DVI-I connector on the faceplate, supporng up

to 2048 x 1536 bpp at 75Hz

• DVI-I connector for dual digital and analog video signal output via the included JYTEK

Y-cable

Hard Drive

Built-in 2.5” 500 GB 7200 RPM SATA hard drive or 120GB SATA solid state driver

I/O Connecvity

Dual Gigabit Ethernet controllers through two RJ-45 connectors with speed/link/acve LED

on the faceplate, with upper connector supporng Wake on LAN.

USB

Four USB 2.0 and two USB 3.0 ports on the faceplate.

GPIB

Onboard IEEE488 GPIB controller through Micro-D 25-pin connector on the faceplate.

Trigger I/O

One SMB connector on the faceplate to route an external trigger signal to/from PXI trigger

bus

Dimensions (3-slot 3U PXI module)

3U/3-slot PXI standard

60.5 W x 128.7 H x 213.2 D mm (2.38 x 5.07 x 8.39 in.)

Slot Requirements

System slot (5V VIO PCI bus) and 2 controller expansion slots on chassis/backplane.

32-bit and 5V VIO PCI bus of system slot.

Do not remove the blue key from the PXI-63980 system connector, only the 5V

VIO PCI bus is compable.

3.3V VIO PCI bus is not.

SEVERE system damage may result.

Weight

0.9 kg (exclusive of packaging)

Environmental

Operang temperature with SSD 0 to 55°C

Operang temperature with HDD 0 to 50°C

Storage temperature -20 to 70°C

Relave humidity , non-condensing 5 to 95%

5

Shock and Vibraon

Funconal shock 30 G, half-sine, 11 ms pulse duraon

Random vibraon:

• Operang 5 to 500 Hz, 0.21 Grms, 3 axes

• Non-operang 5 to 500 Hz, 2.46 Grms, 3 axes

Environmental & Shock and Vibraon values are only guaranteed with use of an

JTTEK-provided SSD/HDD

Cercaon

Electromagnec compability:

• EMC/EMI: CE, FCC Class A

• CE Compliance EN 61326-1

The PXI-63980 meets the essenal requirements of applicable European Direcves.

Power Requirements

Voltage Rail +3�3V +5V +12V Total (W)

Maximum power

consumpon

1.8 21 0.4 115.74

Idle power consumpon 1.4 3.5 Approx.0 22.12

6

2 Getting Started

This chapter describes procedures for installing the PXI-63980 and making preparaons

for its operaon, including hardware and soware setup. Please note that the PXI-63980

is shipped with RAM and HDD or SSD preinstalled. Please contact JYTEK if there are any

problems during the installaon.

Diagrams and illustrated equipment are for reference only.

Actual system conguraon and specicaons may vary.

2�1 Package Contents

Before beginning, check the package contents for any damage and ensure that the following

items are included:

• PXI-63980 Controller (equipped with RAM and HDD or SSD)

• Dual display Y-cable

• PXI-63980 Quick Start Guide

• JYTEK All-In-One USB Flash driver

If any of these items are missing or damaged, contact JYTEK or the dealer from whom you

purchased the product. Save the shipping materials and carton in case you want to ship or

store the product in the future.

Do not install or apply power to equipment that is damaged or missing

components. Retain the shipping carton and packing materials for inspecon.

Please contact your JYTEK immediately for assistance and obtain authorizaon

before returning any product.

2.2 Operating System Installation

For more detailed informaon about the operang system, refer to the documentaon

provided by the operang system manufacturer. Preferred/supported operang systems

for PXI-63980 are:

• Windows 7 32/64-bit

• For other OS support, please contact JYTEK

Most operang systems require inial installaon from a hard drive, oppy drive, or CD-

ROM drive. The PXI-63980 controller supports USB CD-ROM drive, USB ash disk, USB

external hard drive, or a USB oppy drive as the rst boot device. Please see Secon

4.5: Boot Setup for informaon about seng the boot devices. These devices should be

congured, installed, and tested with the supplied drivers before aempng to load the

new operang system.

Read the release notes and installaon documentaon provided by the operang

system vendor. Be sure to read all the README les or documents provided on the

distribuon disks, as these typically note documentaon discrepancies or

compability problems.

7

1. Select the appropriate boot device order from the BIOS Boot Setup Menu based on

the OS installaon media used. For example, if the OS is distributed on a bootable

installaon CD, select USB CD-ROM as the rst boot device and reboot the system

with the installaon CD in the USB CD-ROM drive

2. Proceed with the OS installaon as directed and be sureto select appropriate device

types if prompted. Refer to the appropriate hardware manuals for specic device

types and compability modes of JYTEK PXI products.

3. When installaon is complete, reboot the system and sehe boot device order in the

SETUP boot menu accordingly.

2�3 Hardware Instructions

2�3�1 Faceplate Connectors & Indicators

Figure 2-1: PXI-63980 Faceplate

8

A PXI Trigger Connector

(SMB jack)

E LED indicators

B DVI-I Connector F4X Type-A USB 2.0 connectors

CGPIB Connector

(Micro D-Sub 25P)

G 2X Gigabit Ethernet

DReset Buon H2X USB 3.0

9

2�3�2 PXI Trigger Connector

Trigger

Ground

Figure 2-2: PXI Trigger SMB Jack

The PXI trigger connector is a SMB jack, used to route external trigger signals to or from

the PXI backplane. Trigger signals are TTL-compable and edge sensive. The PXI-63980

provides four trigger roung modes from/to the PXI trigger connector to synchronize PXI

modules, including

• From a selected trigger bus line to PXI trigger connector

• From the PXI trigger connector to a selected trigger bus line

• From soware trigger to a selected trigger bus line

• From soware trigger to PXI trigger connector

All trigger modes are programmable by the provided driver. Please refer to Secon A: PXI

Trigger I/O Funcon Reference for further informaon.

2�3�3 DVI-I Connector

The DVI-I connector connects the PXI-63980 to a monitor, of which both digital (DVI) and

analog (VGA) are supported. If connecng to an analog (VGA) monitor, the included Y-cable

must be installed on the DVI-I connector.

Dual display funcon, providing simultaneous DVI & VGA display, is available, also with the

addion of the included JYTEK Y-cable.

The PXI-63980 supports nave monitor hot-plugging in DVI-Dmonitors, under

Windows 7 with Intel Media Accelerator graphics driver installed, and in VGA

monitors with the included JYTEK Y-cable.

10

Pin Signal Pin Signal Pin Signal Pin Signal

1 TMDS

Data2-

9TMDS

Data1-

17 TMDS

Data0-

C1 Analog Red

2 TMDS Data2+ 10 TMDS

Data1+

18 TMDS

Data0+

C2 Analog Green

3 Shield Ground 11 Shield

Ground

19 Shield

Ground

C3 Analog Blue

4Reserved 12 Reserved 20 Reserved C4 Analog

HSYNC

5Reserved 13 Reserved 21 Reserved C5 Analog Ground

6DDC Clock 14 +5V Power 22 Ground

7DDC Data 15 Ground 23 TMDS Clock+

8 Analog

VSYNC

16 Hot Plug

Detect

24 TMDS

Clock-

Table 2-1: DVI-I Pin Assignment

2�3�4 GPIB Connector

The GPIB connector on PXI-63980 is a micro D-sub 25P connector, controlling external

bench-top instruments. Connecon to other instruments requires the ACL-IEEE488-MD1-A

cable. The onboard GPIB controller provides:

• Full compability with IEEE 488 standard

• Up to 1.5MB/s data transfer rates

• Onboard 2 KB FIFO for read/write operaons

• Driver APIs compable with NI-488.2 driver soware

• Connecon with up to 14 instruments

Connection with up to 14 instruments

1 13

14 25

11

Pin Signal Descripon Pin Signal Descripon

1DIO1# GPIB Data 1 14 DIO5# GPIB Data 5

2DIO2# GPIB Data 2 15 DIO6# GPIB Data 6

3DIO3# GPIB Data 3 16 DIO7# GPIB Data 7

4 DIO4# GPIB Data 4 17 DIO8# GPIB Data 8

5EOI End Or Idenfy 18 REN Remote Enable

6DAV Data Valid 19 Ground Signal Ground

7NRFD Not Ready For Data 20 Ground Signal Ground

8NDAC No Data Accepted 21 Ground Signal Ground

9IFC Interface Clear 22 Ground Signal Ground

10 SRQ Service Request 23 Ground Signal Ground

11 ATN Aenon 24 Ground Signal Ground

12 Chassis Ground Chassis Ground 25 Ground Signal Ground

13 Ground Signal Ground

Table 2-2: GPIB Pin Descripon

2�3�5 Reset Button

The reset buon, acvated by inseron of any pin-like implement, executes a hard reset

for the PXI-63980.

2�3�6 LED Indicators

Four LED indicators on the faceplate indicate operaonal status of the PXI-63980, as follows.

HDD Status

Watchdog Power

Figure 2-3: PXI-63980 LED Indicators

LED

indicator

Color Descripon

Power LED Green Indicates system power. Remains lit when the system

boots normally and main power supply is funconing.

HDD LED Yellow Indicates operang state of the HDD or SSD. Flashes

during access to or acvity on the SATA HDD.

Watchdog Red Indicates status of the watchdog mer, lighng when

watchdog mer has expired. Please refer to Appendix B

for watchdog mer programming informaon.

HS LED Blue Indicates system status, blinking on and o once during

boot when system status is good, and connuously

blinking or remaining lit when the system malfuncons.

Table 2-3: LED Indicator Legend

12

In the event of malfuncon, clear the CMOS (please see Secon 2.3.15: Clearing

CMOS) and reboot the system.

If the system fails to respond properly, please contact JYTEK for assistance.

2�3�7 USB 2�0 Ports

The PXI-63980 provides four USB 2.0 ports via USB Type A connectors on the faceplate, all

compable with hi-speed, full-speed and low-speed USB devices. Supported boot devices

include USB ash drive, USB oppy, USB CD-ROM, and others, with boot priority and device

sengs congurable congured in BIOS. Please see Secon 4.5: Boot Setup for more

informaon.

Pin Signal

1/5 Power 5V

2/6 USB Data-

3/7 USB Data+

4/8 Ground

Table 2-4: USB 2.0 Port Pin Assignment

13

2�3�8 Gigabit Ethernet Ports

Dual Gigabit Ethernet connecon is provided on the PXI-63980 front panel.

Pin 1000Base-T Signal 100/10Base-T Signal

1 MDI0+ TX+

2MDI0- TX-

3 MDI1+ RX+

4MDI2+ Reserved

5 MDI2- Reserved

6MDI1- RX-

7MDI3+ Reserved

8MDI3- Reserved

Table 2-5: PXI-63980 Ethernet Port Pin Assignments

The Ethernet ports each include two LED indicators, one Acve/ Link indicator and one

Speed indicator, funconing as follows.

LED Status Descripon

Acve/Link

(Yellow)

O Ethernet port is

disconnected

On Ethernet port is

connected with no

data transmission

Flashing Ethernet port is

connected with data

transmied/received

Speed(Green/

Orange)

O 10 Mbps

Green 100 Mbps

Orange 1000 Mbps

2�3�9 USB 3�0 Ports

When operang in DOS mode, the PXI-63980 does NOT support:

• KVM switches connected to the USB 3.0 ports

• USB keyboards connected through a USB hub connected to the USB 3.0 ports

The PXI-63980 provides two Type A USB 3.0 ports on the front panel, supporng SuperSpeed,

Hi-Speed, full-speed, and lowspeed transmission for downstream. Mulple boot devices,

including USB ash, USB external HD, and USB CD-ROM drives are supported, with boot

priority congured in BIOS.

While the USB 3.0 ports allow boot from CD-ROM, OS installaon via CD-ROM is not

supported

2�3�10 Onboard Connections and Settings

14

C

A

B

D

E

Figure 2-4: PXI-63980 Onboard Configuration

A SATA Connector

B Clear CMOS switch

CSystem Baery

DBIOS ash backup switch

EBIOS ash socket

2.3.11 Installation Environment

When preparing to install any equipment described in this manual, please refer to Chapter

C: Important Safety Instrucons.

Only install equipment in well lit areas on at, sturdy surfaces with access to basic tools

such as at- and cross-head screwdrivers, preferably with magnec heads as screws and

standos are small and easily misplaced.

Recommended Installaon Tools

• Phillips (cross-head) screwdriver

• Flat-head screwdriver

• An-stac wrist strap

• An-stac mat

JYTEK PXI-63980 system controllers are electrostacally sensive and can be easily damaged

by stac electricity. The equipment must be handled on a grounded an-stac mat, and

operators must wear an an-stac wristband, grounded at the same point as the an-stac

mat.

Inspect the carton and packaging for damage. Shipping and handling may cause damage to

the contents. Ensure that all contents are undamaged before installing.

JYTEK PXI-63980 User manual

Popular Controllers manuals by other brands