K Tool International KTI63709 User manual

KTI63709 07/10/14
10 TON PORTABLE RAM KIT
OWNERS MANUAL
SPECIFICATIONS
KTI63709
Ram Capacity................................................. 10 Ton @ 7,250 psig
Ram Minimum Height .......................................................... 12.68"
Stroke ..................................................................................... 5.12"
Fluid Capacity .................................................................... 17.5 oz.

2
KTI63709 07/10/14
WARNING
WARNING
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not
legible, contact K-Tool International for replacements. If the operator is not fluent in English, the product and safety instructions shall be
read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the
operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of Portable Hydraulic Power Kits is subject to certain hazards that cannot be prevented by mechanical means, but only by the exer-
cise of intelligence, care, and common sense. The versatility of use is limited only by the imagination and ingenuity of its operator; therefore
K-Tool International cannot be responsible for product damage or personal injury due to faulty operator judgement or improper use of the
kit. It is essential to have personnel involved in the use and operation of the kit who are careful, competent, trained, and qualified in the safe
operation of the kit and its proper use when working on vehicle frames and body parts. Examples of hazards are dropping or slipping of
load, caused by improperly securing loads, overloading, off centered loads, and improper setups. Additional hazards may be caused by the
rupture or bursting of the hydraulic hoses and related fittings due to abuse, misuse, improper setup and using the kit for a purpose for which
it was not intended.
METHODS TO AVOID HAZARDOUS SITUATIONS
• Read,study,understand,andfollowallinstructionsbeforeoperatingthisdevice.
• ThekitownerisresponsibleforthekitbeingusedinaccordancewithOSHA,state,andlocalsafetystandards.
• UserandbystandersweareyeprotectionthatmeetsANSIZ87.1andOSHAstandards.
• Donotexceedtheratedcapacity.Somekitattachmentsdonotmatchthekit’sratedcapacity.Thekit’sratedcapacitycanalsobe
reduced according to the number of kit attachments and extension tubes used and their assembly to the cylinder/ram. USE THE
PRESSUREGAUGE(#11)INCLUDEDINTHISKITTOMONITORCORRECTLOADCAPACITIES.
 WedgeRamsareratedat1toncapacity.
 RubberHeadsareratedat1/2toncapacityinthe4tonkitand1toncapacityinthe10tonkit.
• Donotoverextendtherams.
• Whenusingextensiontubes,positiontheshortesttubefarthestawayfromthecylinder.
• Attachmentsandextensiontubesmustbealignedandfullyengagedsotheramforceisstraightandavoidsoff-centerloadconditions.
• Beforeoperating,tightenallhose,gaugeandmanifoldconnectionssotheyaresecureandleakfree.Donotovertightenoritmaycause
premature thread failure or split pressure fittings. Tighten all hose quick disconnect fittings by hand only.
• Donotsubjectthehosetoextremeheatorcold,sharpsurfaces,abrasion,impact,kinking,twisting,curling,bendingoranyconditionthat
restricts or affects fluid flow.
• Makesuresetupisstableandsecurebeforeperforminganywork.
• Usethiskitfortheintendedpurposeofvehiclebody/framerepaironly.
• Onlycomponentssuppliedwiththiskitshallbeusedwiththiskit.
• Noalterationsormodicationsshallbemadetoanyofthekitcomponents.
•ThisproductmaycontainoneormorechemicalsknowntotheStateofCaliforniatocausecancerandbirthdefectsorother
reproductive harm. Wash hands thoroughly after handling.
• Failuretoheedthesewarningsmayresultinpersonalinjury,propertydamage,orboth.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCEINSTRUCTIONSandcomplywiththem,andfailuretocomplywiththeMETHODSTOAVOIDHAZARDOUSSITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING INFORMATION

3
KTI63709 07/10/14
OWNER'S MANUAL
PORTABLE HYDRAULIC POWER KIT SETUP INSTRUCTIONS
This is the Safety Alert Symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
SETUP
1. Refer to the parts list and drawing in this manual to identify parts mentioned in this setup procedure.
2. Install the ram (part C.) at the end of the hose (part B.) and secure the quick disconnect ttings together by hand tightening the
threaded sleeve (#S10) on the ram tting (#S11) to the hose (part B.).
3. Insert the pump handle (#P41) in the pump linkage receiver (#P40) and rotate the handle (#P41) clockwise until tight. Before operating
the pump, turn the reservoir vent screw (#P09) in a counterclockwise direction until it stops.
4. During shipping or handling air may have become trapped in the hydraulic system. If the pump (part A.) is not providing a full incremental
pump stroke or the ram feels spongy, it will be necessary to purge the air out of the hydraulic system:
a. Before operating the pump (part A.), turn the reservoir vent screw (#P09) in a counterclockwise direction until it stops.
b. Place the pump (part A.) horizontally on a table. Position the hose (part B.) and ram (part C.) over the edge of the table, lower than the
pump (part A.) with the ram piston (#R03) pointing down.
c. Close the pump’s release valve (#P15) and pump the ram to its complete or its furthest extension. Open the pump’s release valve
(#P15) to retract the ram (part C.) all the way. Conduct this procedure several times without a load.
d. Repeat steps “b” and “c” until all air is purged from the system.
OPERATING INSTRUCTIONS
This is the Safety Alert Symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Study the work to be done in order to determine the type ram and other attachments you will be using. Consult the enclosed
chart titled “Applicable force for component set ups” in order to determine the maximum allowable force to be used in your
specific setup. All rams have female hose disconnects attached to them, and the end of the hose has the male quick disconnect at-
tached to it. Insert the end of the hose (part B.) all the way in to the ram’s female quick disconnect (#S11). Slide the female connec-
tor’s threaded sleeve (#S10) on to the threads at the end of the hose (part B.) and hand tighten. Never use any tools to tighten this
connection.
2. Consult this Owner’s Manual section titled APPLICABLE FORCE FOR COMPONENT SET UPS for typical attachment and extension
tube setups and pay very close attention to the corresponding load ratings of certain attachment connections. The use of extension
tubes, ram or plunger toes greatly reduces the hydraulic system’s capacity. When using extension tubes, put the shortest tubes on
the ends of the setup.
3. The pump (part A.) may be operated in the horizontal or vertical position but the pump (part A.) must point down when used in the
vertical position.
4. Make sure all hydraulic and attachment connections are fully engaged and tight so ram force is straight in order to avoid off-center
load conditions.
5. During setup, make sure the hose routing avoids kinks, twists, curls or bends that will impede hydraulic uid ow. Do not use the
hose (part B.) as a means to carry the kit components. Do not subject the hose (part B.) to any hazards such as re, extreme heat or
cold, sharp surfaces, or heavy impact. IF A HOSE (PART B.) RUPTURES, BURSTS, OR NEEDS TO BE DISCONNECTED, IMMEDI-
ATELY SHUT THE PUMP (PART A.) OFF AND OPEN THE RELEASE VALVE (#P15) TO RELEASE HYDRAULIC PRESSURE. NEVER
GRASP A LEAKING PRESSURIZED HOSE, FITTING OR COMPONENT WITH YOUR HANDS OR SUFFER SERIOUS INJURY.
6. Always use the pressure gauge (#11) to make sure you are within the required force range when operating the system.
7. In order to pump the ram (part C.), it will be necessary to turn the release valve knob (#P15) in a clockwise direction until tight.
Tighten by hand only.
8. Pumping the handle (#P41) up and down transfers the hydraulic uid from the pump’s reservoir (#P04), through the hose (part B.), in
to the cylinder and extends the ram with each incremental pump stroke.
9. To release the pressure and return the ram (part C.) back in to its cylinder (#R14) , turn the release valve knob (#P15) in a counter-
clockwise direction very slowly. Turning the release valve knob (#P15) slowly will determine the speed in which the ram (part C.) will
retract back into its cylinder (#R14).
IMPORTANT: The pump includes an overload valve that will activate at the pump’s rated capacity only. If the setup requires a re-
duced rating, the operator is responsible for using the gauge to determine when to stop pumping since the overload valve (#P22) is
set to a higher rating.
10. Make sure the ram (part C.) is completely retracted inside its cylinder (#R14) before disconnecting the hose from the cylinder.
11. The the hose (part B.) and the ram (part C.) are repeatedly disconnected and exposed to shop or work place oors that are covered
with dirt and debris. It is important to use the dust caps (#P18) provided to prevent contaminants from entering the air and hydraulic
systems.
12. Based on continuous engagement and disengagement of the hose (part B.) from the cylinder (#R14), eventually it will become
necessary to add hydraulic uid to the pump’s reservoir (#P04). Completely retract the ram before adding hydraulic uid. Do not
overll in order to avoid personal injury and hydraulic malfunction. Use only hydraulic jack oil, ChevronHydraulicOilAWISO32orits
equivalentUnocalUnaxAW150. Other uids will cause damage to the hydraulic seals.

4
KTI63709 07/10/14
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the kit in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements. The kit must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Based on continuous engagement and disengagement of the hose from the cylinder, eventually it will become necessary to add hydrau-
lic uid to the pump’s reservoir. Completely retract the ram before adding hydraulic uid. Do not overll in order to avoid personal injury
and hydraulic malfunction. Use only hydraulic jack oil, ChevronHydraulicOilAWISO32oritsequivalentUnocalUnaxAW150. Other
uids will cause damage to the hydraulic seals.
IMPORTANT: In order to prevent seal damage and kit failure, never use alcohol, hydraulic brake uid or transmission oil in the pump.
3. Every kit owner is responsible for keeping the kit labels clean and readable. Use a mild soap solution to wash external surfaces
of the kit components but not any moving hydraulic components.
4. Do not attempt to make any hydraulic repairs unless you are a qualied hydraulic repair person that is familiar with this equipment.
Repairs must be performed by an authorized service center.
TROUBLESHOOTING
PROBLEM: UNIT WILL NOT LIFT RATED LOAD
ACTION: Purge air from hydraulic system by following procedure under SETUP.
PROBLEM: UNIT WILL NOT SUSTAIN RATED LOAD OR FEELS "SPONGY" UNDER RATED LOAD
ACTION: Purge air from hydraulic system by following procedure under SETUP.
PROBLEM: UNIT WILL NOT LIFT TO FULL HEIGHT
ACTION: Purge air from hydraulic system by following procedure under SETUP.
PROBLEM: UNIT STILL DOES NOT OPERATE
ACTION: Contact K-Tool International authorized hydraulic service center.
OWNER'S MANUAL
Spreader Capacity
100% of Ram Capacity 100% of Ram Capacity
50% of Ram Capacity 25% of Ram Capacity
50% of Ram Capacity
50% of Ram Capacity
25% of Ram Capacity
6% of Ram Capacity
APPLICABLE FORCE
FOR COMPONENT SET UPS

5
KTI63709 07/10/14
K-Tool International warrants that all jacks and service-related equipment will be free from defects in material and workmanship for a
period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser only. If any jack or
service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s option, without
charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any equipment which
has been altered or used with special attachments other than those recommended. This warranty does not cover repairs made by
anyone who is not a K-Tool International Professional Lifting Equipment Authorized Repair Center.
All HD & XD jacks or service-related equipment will be replaced or repaired at K-Tool International’s option during the 2 year warranty
period.
During the 2 year warranty period, all alleged defective products must be shipped, freight prepaid, along with proof of date-of-purchase,
to your nearest K-Tool International Professional Lifting Equipment Authorized Warranty Center. Be certain to include your name,
address and phone number along with proof-of-purchase information, and a brief description of the alleged defect. The product will be
returned to the customer, freight prepaid.
Many alleged defectives may simply be handled by calling your nearest Service Center for parts. See pages 19 - 21 for a listing of
authorized warranty service centers.
In no event shall K-Tool International be liable for incidental or consequential damages. The liability on any claim for loss or damage
arising out of the sale, resale or use of a jack or related service equipment, shall in no event exceed the purchase price. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED IN CONNECTION WITH THE SALE OF K-TOOL
INTERNATIONAL PROFESSIONAL LIFTING EQUIPMENT. ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
WARRANTY HANDLING PROCEDURES AND GUIDELINES FOR HD AND XD LIFTING EQUIPMENT

6
KTI63709 07/10/14
10 TON PORTABLE RAM KIT
KTI63709
10 TON RAM KIT
PARTS LIST AND DRAWING
A. PUMP
B. HOSE
C. RAM
D. SPREADER
Item # Part # Description Quantity
A KTP63709A Pump (Incl. Hose) 1
B KTP63709B Hose 1
C KTP63709C Ram 1
D KTP63709D Spreader 1
01 KTP6370901 Case 1
KTP63709WH Wheel w/ Hardware for Case 2
02.1 KTP6370902.1 4.33" (110mm) Extension 1
02.2 KTP6370902.2 10.43" (265mm) Extension 1
02.3 KTP6370902.3 14.37" (365mm) Extension 1
02.4 KTP6370902.4 20.47" (520mm) Extension 1
Item # Part # Description Quantity
03 KTP6370903 Flat Base 1
04 KTP6370904 Ram Toe 1
05 KTP6370905 Plunger Toe 1
06 KTP6370906 Wedge Head 1
07 KTP6370907 V-Base 1
08 KTP6370908 Male Connector 1
09 KTP6370909 Serrated Saddle 1
10 KTP6370910 Rubber Head 1
11 KTP6370911 Pressure Gauge 1
KTP63709LK Product Label 1

7
KTI63709 07/10/14
10 TON PORTABLE RAM KIT
KTI63709
KTP63709A
10 TON PUMP
PARTS BREAKDOWN
Items identified by an asterisk are available in pump seal kit, KTP63709PSK.
Item # Part # Description Quantity
PO1 Valve Block 1
PO2 Oil Filter 1
PO3 * O-Ring 2
PO4 Reservoir 1
PO5 Tie Rod 1
PO6 Nylon Ring 1
PO7 Oil Filler Screw 1
PO8 Sealing 1
P09 KTP63709P09 Reservoir Vent Screw
(Incl. #6-9) 1
P10 Screw 1
P11 * O-Ring 2
P12 KTP63709P12 Pump Foot 1
P13 * Ball 2
P14 * O-Ring 1
P15 KTP63709P15 Release Valve 1
P16 KTP63709P16 Hydraulic Hose 1
P17 KTP63709P17 Coupler 1
P18 KTP63709P18 Hose Dust Cover 1
P19 * Ball 1
P20 Ball Cap 1
P21 * Spring 1
P22 Screw 1
P23 * O-Ring 1
P24 Screw 1
Item # Part # Description Quantity
P25 Screw Protector 1
P26 * Nylon Ring 1
P27 * Valve Base 1
P28 Valve Cover 1
P29 * Washer 1
P30 * Seal 1
P31 * O-Ring 1
P32 * Washer 1
P33 Screw 1
P34 * O-Ring 1
P35 * Washer 1
P36 Piston 1
P37 Pin 1
P38 Retaining Ring 2
P39 Pin 1
P40 Pump Linkage Receiver 1
P41 KTP63709P41 Handle (Incl. #42) 1
P42 Handle Sleeve 1
P43 Screw 1
P44 * Spring 1
P45 * Steel Ball 1
P46A KTP63709P46A Gauge Adapter Assembly 1
P49 KTP63709P49 Pressure Gauge 1
P52 * Nylon Ring 1
*
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.

8
KTI63709 07/10/14
10 TON PORTABLE RAM KIT
KTI63709
KTP63709D
SPREADER PARTS BREAKDOWN
Items identified by an asterisk are available in Spreader Seal Kit, KTP63709SSK.
Items identified by an asterisk are available in Ram Seal Kit, KTP63709RSK.
*
*
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
Item # Part # Description Quantity
S1 Pin 1
S2 Circlip 2
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-Ring 1
S9 End Cap 1
KTP63709CP Coupler 1
KTP63709C
RAM PARTS BREAKDOWN
Item # Part # Description Quantity
R01 KTP63709R01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 * Nylon Ring 1
R07 * Sealing Ring 1
R08 * Circlip 1
R09 Nut 1
R10 Spring 1
R11 Screw 1
R12 KTP63709R12 Protection Cap 1
R13 Ring for Ram 1
R14 Cylinder 1
R15 Screw 1
KTP63709CP Coupler 1
(Includes: S10, S11, P11, S12, S13)
(Includes: S10, S11, P11, S12, S13)

9
KTI63709 07/10/14
10 TON EQUIPO PORTÁTIL DE PISTONES
MANUAL DEL PROPIETARIO
ESPECIFICACIONES
KTI63709
Ram Capacidad................................... 10Toneladas@7,250psig
Altura mínima del pistón ......................................... 322mm/12.68"
Recorrido ................................................................... 130mm/5.12"
Capacidad Fluida ............................................................... 17.5oz.

10
KTI63709 07/10/14
Este símbolo indica una alerta de seguridad y se usa para
advertir sobre peligro de accidentes personales. Observe toda
la información de seguridad que sigue a este símbolo para
evitar la posibilidad de que ocurran lesiones o muerte.
IMPORTANTE: LEA ESTAS INSTRUCCIONES ANTES DE USAR EL DISPOSITIVO
ANTES DE USAR ESTE DISPOSITIVO, LEA ESTE MANUAL DETENIDAMENTE. PROCURE ENTENDER SUS PROCEDIMIENTOS OPERATIVOS,
ADVERTENCIAS DE SEGURIDAD Y FORMA DE MANTENIMIENTO.
El propietario es responsable de asegurarse de que todo el personal lea este manual antes de usar el dispositivo. Asimismo, es responsabilidad del
propietario mantener este manual en buenas condiciones en una ubicación conveniente para su consulta. Si las etiquetas del manual o producto son
ilegibles o no están en su lugar, deberá ponerse en contacto con K-Tool Internatinoal para obtenerlas gratis. El comprador/propietario o una persona
designada deberá leer y comentar el producto y las advertencias de seguridad en la lengua materna del operario que no hable inglés fluido, a fin de
asegurarse de que comprende el contenido.
NATURALEZA DE LAS SITUACIONES DE RIESGO
El uso de los conjuntos de potencia hidráulica portátiles está sujeto a ciertos peligros los que no se pueden prevenir por medidas mecánicas,
sino sólo por ejercer la inteligencia, cuidado y sentido común. La versatilidad del uso está limitada sólo por la imaginación y la ingeniosidad
de su operador; por ende, K Tool International no podrá responsabilizarse por los daños al producto o lesiones personales debido al juicio
incorrecto del operador o al uso inadecuado del equipo. Es imprescindible contar con personal involucrado en el uso y la operación del equipo
quienes sean cuidadosos, competentes, entrenados y calificados en la operación segura del equipo y su uso adecuado al momento de trabajar
sobre los armazones del vehículo y las partes del cuerpo. Ejemplos de los peligros son las caídas o el deslizamiento de la carga, ocasiona-
dos por la sujeción inadecuada de las cargas, la sobrecarga, las cargas no centradas y los montajes inadecuados. Los peligros adicionales
se podrán ocasionar por la rotura o explosión de las mangueras hidráulicas y acoplamientos relacionados. debido al uso, mal uso, el montaje
inadecuado y además usar el equipo para algún uso para el cual no fue destinado.
FORMAS DE EVITAR LAS SITUACIONES DE RIESGO
• Estudie,comprendaysigatodaslasinstruccionesantesdeoperarestedispositivo.
•El propietario del equipo debe asegurar que el equipo sea usado de acuerdo con las normas de seguridad locales, estatales y de OSHA.
• LosoperadoresyobservadoresdeberánllevarpuestoproteccióndeojosquecumplaconlasnormasANSIZ87.1yOSHA.
• Noexcedalacapacidadnominaldeldispositivo.Algunosaccesoriosdelequiponoemparejanconlacapacidadnominaldelequipo,ylacapacidad
nominal del equipo puede también ser reducida según el número de accesorios del equipo y tubos de extensión usa dos y su montaje al cilindro/
pistón.
 USEELCALIBRADOR(#11)DEPOTENCIAINCLUIDOCONESTEEQUIPOPARAMONITOREARLASCAPACIDADESCORRECTASDECARGA.
 Lospistonesdecuñaestánclasicadosaunacapacidadde1tonelada.
 Loscabezalesdehuleestánclasicadosaunacapacidaddeuna1/2toneladaenunjuegode4toneladasyunacapacidadde1tonelada
 enunjuegode10toneladas.
• Nosobreextiendalospistones.
• Duranteelusodelostubosdeextensión,coloqueeltubomáscortoaladistanciamáslejosdelcilindro.
• Losaccesoriosytubosdeextensióndebenestaralineadosycompletamenteencajadosconelndequelafuerzadelpistónesté
recto y evite las condiciones de carga no centradas.
• Previoalaoperación,aprietetodaslasconexionesdelamanguera,delindicadorydelcolectordeescapeparaqueesténsegurasylibrasdefugas.
No los sobre apriete ya que se podría ocasionar fallas prematuras de las roscas, igual como accesorios de presión partidos. Apriete todos los
accesorios de manguera de desconexión rápida manualmente solamente.
• Noexpongalamangueraalcalornielfríoextremo,superciesagudas,abrasiones,impacto,vueltas,retorcimiento,ondulaciones,
dobladuras ni ninguna otra condición que restrinja o afecte el flujo de fluido.
• Asegúresequeelmontajeestéestableyseguroantesderealizarcualquiertrabajo.
• Useesteequiposóloparaelusodestinadodereparacióndelarmazón/carroceríadelvehículo.
• Sólosedebenusarcomponentesprovistosconesteequipo.
• Nosedebehacerningunamodicaciónnialteraciónaloscomponentesdelequipo.
• EsteproductopuedecontenersustanciasquímicasconsideradasporelEstadodeCaliforniacomocausantesdecáncer,demalformaciones
congénitas u otros daños en el sistema reproductivo. Lávese bien las manos después de manipular el producto.
• Hacercasoomisoaestasadvertenciaspuedeocasionarlesionespersonales,dañosalapropiedadolosdos.
CONSECUENCIAS DE NO PREVENIR LAS SITUACIONES DE RIESGO
No leer, comprender u observar todo el contenido de este manual en relación con sus INSTRUCCIONES DE USO, ADVERTENCIAS DE SEGURIDAD y
FORMA DE MANTENIMIENTO, así como desatender las FORMAS DE EVITAR LAS SITUACIONES DE RIESGO, puede provocar accidentes que tengan
como consecuencia lesiones graves, peligro de muerte o daños materiales.
ADVERTENCIA: Indica una situación
peligrosa que si no se evita, puede
provocar la muerte o lesiones graves.
INFORMACIÓN DE ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA