Kallista P24300 User manual

1072008-2-B
Page 1 of 4
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION INSTRUCTIONS P24300, P24301
Single Control Lav Faucet
P24301-00 P24301-TL
P24300-00 P24300-TL

1072008-2-B
Page 2 of 4
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION INSTRUCTIONS P24300, P24301
Single Control Lav Faucet
THANK YOU FOR CHOOSING KALLISTA
BEFORE YOU BEGIN
TOOLS AND MATERIALS
1. INSTALL HOSES INTO THE FAUCET
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before
you install your Kallista product. If you encounter any installation or performance problems, please do not
hesitate to contact us at the phone number listed at the bottom of the page.
Priorto installation, unpack the faucet and drain and inspect it fordamage. If the product is damaged,
please contact Kallista immediately at the phone numberlisted at the bottom of the page.
Shut off the main watersupply.
Observe all local plumbing and building codes.
If possible, install the faucet to the lavatory before installing the lavatory.
Kallista reserves the right to make revisions in the design of plumbing products without notice, as specified in
the Price Book.
Adjustable
Wrench
Hex
Wrench
Thread
Sealant
Plumbers
Putty
Insert the lift rod in small hole in escutcheon. Slide
escutcheon up to bend in lift rod.
Ensure that O-ring is installed in bottom of escutcheon.
Feed the hoses through the escutcheon one at a time.
Install escutcheon onto bottom of faucet, guiding lift rod
into slot in back of faucet.
Install the mounting stud into the bottom of the faucet.
Mounting Stud
Escutcheon
O-ring
Lift Rod
P24301-00 P24301-TL
P24300-00 P24300-TL

1072008-2-B
Page 3 of 4
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P24300, P24301
Single Control Lav Faucet
INSTALLATION INSTRUCTIONS
2. INSTALL THE FAUCET
3. CONNECT THE SUPPLIES
Feed the supply hoses, stud and lift rod
through faucet hole of the lavatory or mounting
surface.
Slide the washer over the mounting stud and
secure the faucet to the lavatory or mounting
surface by threading the nut onto the mounting
stud.
If the lavatory is not installed, install it at this time.
Follow the lavatory manufacturer’s instructions.
Connect the supply hoses to the supply stops. (Left is
hot - right is cold.)
Wrench-tighten all connections.
Supply
Stop
Supply
Hose
Nut
Washer
Lavatory or
Mounting Surface
Supply Hoses Mounting Stud
Lift Rod
P24301-00 P24301-TL
P24300-00 P24300-TL

1072008-2-B
Page 4 of 4
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P24300, P24301
Single Control Lav Faucet
INSTALLATION INSTRUCTIONS
4. INSTALL THE DRAIN
5. COMPLETE INSTALLATION
Apply a ring of plumbers putty or other sealant to the
underside of the flange according to the putty manu-
facturer's instructions.
Insert the flange into the fixture drain hole.
From the underside of the basin, slide the gasket
(tapered side up) and washer onto the bottom of the
flange. Partially thread the flange nut onto the flange.
Do not fully tighten the flange nut at this time.
Wrap the bottom 1/3 of the flange threads with three
layers of sealant tape.
Insert the body washer into the drain body. Tighten
the drain body to the bottom of the flange. Once
tightened to the flange, rotate the drain body with the
seal facing the back of the fixture. Securely tighten
the flange nut. Use care to avoid scratching the
finish.
Using a damp cloth, remove any excess putty or
sealant.
Insert the stopper into the flange.
Insert the seal into the drain body. Assemble the rod,
nut and elbow as shown.
Connect the tailpiece and P-trap (not supplied).
Ensure that all connections are watertight.
Remove the aerator assembly by turning it counter-
clockwise (Figure D).
Open the drain. Turn on the main water supply and
check for leaks. Repair as needed.
Open both hot and cold valves and run water through
the spout for one minute to remove debris. Check for
leaks in the flexible hose connections. Turn valves
off.
Re-install the aerator assembly.
Flange
(Apply plumbers putty)
(Apply 3 layers of sealant
tape to bottom 1/3)
Gasket
Washer
Flange Nut
Body Washer
Drain Body
Rod
Nut
Stopper
Lift Rod
Elbow
Aerator Assembly
P24301-00 P24301-TL
P24300-00 P24300-TL