Kallista P21650 User manual

INSTALLATION INSTRUCTIONS
Handshower, Hose
& HandshowerAccessories
1188577-2-FQuestions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA(1-888-452-5547) or kallista.com
1 of 5
P21650, P21660, P24452, P24453,
P24454, P24456, P24743, P24745,
P24746, P24761, P24843
©2014 KALLISTA

INSTALLATION INSTRUCTIONS
Handshower, Hose
& HandshowerAccessories
1188577-2-E Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA(1-888-452-5547) or kallista.com
2 of 5
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
WARNING: Risk of scalding.High water temperature can cause severe burns. Set the water temperature
at or below 120°F (49°C) following the adjustment procedure in the valve Installation Instructions.
CAUTION: Risk of scalding. KALLISTAlow-flow showerheads/handshowers are designed for use with
compatible KALLISTAvalves. When installing a low-flow product to an existing showering system, verify
compatibility before showering. Do not use this KALLISTAlow-flow product with a shower valve that allows the
water temperature to become too hot when other plumbing products are used.
Prior to using your shower, verify your new showerhead/ handshower is compatible with your shower valve
(located behind the wall):
While standing outside the shower, turn on the shower valve. Do not step into the shower.
Adjust the water to your typical showering temperature.
Have someone flush the nearest toilet.
With your hand, carefully check the water temperature from the showerhead/handshower while the toilet is
refilling.
If the water becomes significantly more hot, you will need to replace the shower valve with a compatible
KALLISTAvalve or return your showerhead/handshower.
NOTE: Plumbing codes may require a vacuum breaker be installed in-line to handshowers. Please consult with
local plumbing codes.
Carefully plan the location of the wall supply elbow and fixed wall bracket to avoid the possibility of the
handshower hose interfering with the operation of any faucets and/or drains, etc.
Please read all instructions before you begin.
Observe all local plumbing and building codes.
Shut off the water supply.
Inspect the supply piping for damage. Replace as necessary.
KALLISTA reserves the right to make revisions in the design of products without notice, as specified in the
Price Book.

INSTALLATION INSTRUCTIONS
Handshower, Hose
& HandshowerAccessories
1188577-2-E Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA(1-888-452-5547) or kallista.com
3 of 5
TOOLSAND MATERIALS
Adjustable WrenchDrill Pipe Wrench
Thread Sealant
Assorted Screwdrivers
Pencil Tape Measure Level Hex Wrench
.
1. INSTALL THE SUPPLY ELBOW (P24452)
O-Ring
Supply Elbow
Shower Ell
Apply thread sealant tape.
Adapter
Install a temporary nipple into the shower ell.
Run water through the system to flush out dirt and debris.
Remove the temporary nipple from the shower ell.
Apply several layers of sealant tape around the straight end of the threaded adapter.
Install the threaded adapter into the supply elbow.
NOTE: A hex wrench can be used to tighten the threaded adapter.
Apply several layers of sealant tape around the exposed tapered end of the threaded adapter.
Install the O-ring into the back of the supply elbow.
Thread the adapter and supply elbow onto the shower ell.
Turn on the water and allow water to flow through the supply elbow.
Check connection for leaks. Repair as needed.

INSTALLATION INSTRUCTIONS
Handshower, Hose
& HandshowerAccessories
1188577-2-E Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA(1-888-452-5547) or kallista.com
4 of 5
2. INSTALL THE FIXED WALL BRACKET (P24453)
Screw
Press and hold
legs together.
Anchor
Fixed Wall Bracket
13/16"
(21 mm)
Drill holes using a 5/16" bit.
Determine the location for the fixed wall bracket.
Mark the hole locations for the wall anchors.
Drill the holes and install the wall anchors.
Attach the fixed wall bracket to the wall with the screws.
3. INSTALL THE HANDSHOWERAND HOSE
Handshower
Washer
Fixed Wall Bracket
Handshower Connector
Supply Elbow
Washer
Elbow Connector
Insert a washer into the elbow connector end of the shower hose.
Attach the shower hose to the supply elbow. Run cold and hot water through the shower hose to flush out
dirt and debris.
Insert the other washer into the threads of the handshower connector.
Thread the handshower into the shower hose. Tighten with an adjustable wrench.
Turn on the water. Check for leaks and smooth operation.
Place the handshower in the fixed wall bracket.

INSTALLATION INSTRUCTIONS
Handshower, Hose
& HandshowerAccessories
1188577-2-E Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA(1-888-452-5547) or kallista.com
5 of 5
4. INSTALL THE OPTIONAL SLIDEBAR (P24456)
Cap
Setscrew
O-Ring
Coupling
Screw
Hub
Sleeve
Escutcheon
Anchor
Cap
Setscrew
O-Ring
Coupling
Tube
Handshower
Bracket
Drill a 5/16" hole
for the anchor.
Determine the location for the slidebar.
Mark the hole locations for the wall anchors.
Drill the holes and install the wall anchors.
Attach the escutcheons, sleeves, and hubs with the screws.
Slide the handshower bracket onto the tube.
Insert the couplings into the ends of the tube. Line up the holes in the tube with the holes in the couplings.
Place the tube over the sleeves.
Tighten the setscrews so they engage with the groove in the hubs.
Screw the caps onto the exposed ends of the setscrews.

INSTALLATION INSTRUCTIONS
Integrated Supply Elbow
1230883-2-B
1 of 3
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
Wall Bracket with
©2015 KALLISTA
P21652P21651

INSTALLATION INSTRUCTIONS
Integrated Supply Elbow
1230883-2-B
2 of 3
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
Wall Bracket with
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
NOTE: Plumbing codes may require a vacuum breaker be installed in-line to handshowers. Please consult with
local plumbing codes.
Carefully plan the location of the wall bracket to avoid the possibility of the handshower hose interfering
with the operation of any faucets and/or drains, etc.
Please read all instructions before you begin.
Observe all local plumbing and building codes.
Shut off the water supply.
Inspect the supply piping for damage. Replace as necessary.
KALLISTA reserves the right to make revisions in the design of products without notice, as specified in the
Price Book.
TOOLSAND MATERIALS
1/2" NPT
Nipple
Sealant
Tape
Clear
Sealant
Strap
Wrench
Tape
Measure
Rags

INSTALLATION INSTRUCTIONS
Integrated Supply Elbow
1230883-2-B
3 of 3
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
Wall Bracket with
1. INSTALL THE PIPE NIPPLE
11/16" (17 mm) Beyond
Finished Wall
1/2" NPT
Nipple
Apply
sealant tape.
1-5/8" (41 mm) Max
3/8" (10 mm)
Max
Apply sealant tape to one end of a 1/2” NPT nipple.
Install the nipple to extend 11/16″(17 mm) beyond the finished wall.
Ensure the gap between the nipple and finished wall is no more than 3/8” (10 mm).
2. INSTALL THE WALL BRACKET
Outlet
Wall Bracket
Apply sealant tape.
Apply sealant tape to the exposed threads of the nipple.
Thread the wall bracket onto the nipple.
Using a clean strap wrench, tighten the bracket flush to the wall with the outlet oriented down.
Apply a bead of clear sealant around the perimeter of the bracket.
Turn on the water and allow water to flow through the bracket to flush out debris.
Check connection for leaks. Repair as needed.

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
1 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
P21520 P21521
P21522 P21523

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
2 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
IMPORTANT IMFORMATION
Observe all local plumbing and building codes.
Shut off the main water supply.
The appearance of your product may differ from what is shown in these instructions, however, the
installation procedure is the same.
KALLISTA reserves the right to make revisions in the design of products without notice, as specified in the
Price Book.
TOOLSAND MATERIALS
Strap Wrench Sealant Tape

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
3 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
INSTALL THE SHOWER ARM
Shower Ell (Wall)
Escutcheon (Not Provided)
Shower Arm
Showerhead
(Not Provided)
Apply thread
sealant tape.
Shower Ell
(Ceiling)
Escutcheon
(Not Provided)
Shower Arm
CAUTION: Risk of product damage. To avoid plugging the showerhead spray outlets, use thread sealant tape
on the shower arm threads. Do not use thread sealant compound (pipe dope).
NOTE: The showerhead and escutcheon are not provided.
Remove the temporary nipple from the shower ell.
Slide the escutcheon onto the end of the shower arm that will be closest to the wall/ceiling.
Apply thread sealant tape to the shower arm threads closest to the wall/ceiling.
Thread the showerarm into the shower ell.
Carefully tighten the shower arm with a clean strap wrench.
With the showerhead off, turn on the water to flush out the system.
Check connections for leaks. Repair as needed.
Turn off the water.
Install the showerhead according to the showerhead manufacturer’s instructions.

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
1 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
P21520 P21521
P21522 P21523

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
2 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
IMPORTANT IMFORMATION
Observe all local plumbing and building codes.
Shut off the main water supply.
The appearance of your product may differ from what is shown in these instructions, however, the
installation procedure is the same.
KALLISTA reserves the right to make revisions in the design of products without notice, as specified in the
Price Book.
TOOLSAND MATERIALS
Strap Wrench Sealant Tape

INSTALLATION INSTRUCTIONS
ShowerArms
1193441-2-A
3 of 3 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA(1-888-452-5547) or FAX [phone].
INSTALL THE SHOWER ARM
Shower Ell (Wall)
Escutcheon (Not Provided)
Shower Arm
Showerhead
(Not Provided)
Apply thread
sealant tape.
Shower Ell
(Ceiling)
Escutcheon
(Not Provided)
Shower Arm
CAUTION: Risk of product damage. To avoid plugging the showerhead spray outlets, use thread sealant tape
on the shower arm threads. Do not use thread sealant compound (pipe dope).
NOTE: The showerhead and escutcheon are not provided.
Remove the temporary nipple from the shower ell.
Slide the escutcheon onto the end of the shower arm that will be closest to the wall/ceiling.
Apply thread sealant tape to the shower arm threads closest to the wall/ceiling.
Thread the showerarm into the shower ell.
Carefully tighten the shower arm with a clean strap wrench.
With the showerhead off, turn on the water to flush out the system.
Check connections for leaks. Repair as needed.
Turn off the water.
Install the showerhead according to the showerhead manufacturer’s instructions.

9/16" (14 mm) –
1-1/16" (27 mm)
Standard Wall: Use the #1 adapter
and the 13/16” (21 mm) screw.
3/16" (5 mm) –
9/16" (14 mm)
Thin Wall: Use the #3 adapter and
the 13/16” (21 mm) screw.
1Determine the valve stem adapter
length. Refer to the plaster guard.
Important Information
Observe all local plumbing and
building codes.
Record your model number below
for future reference:
52-way valve: Water should flow
from the main shower accessory
with the handle position at 4
o’clock.
4Position the handle on the valve
stem adapter.
3Temporarily fit the valve stem
adapter on the spline adapter.
2Remove the plaster guard. Place
the spline adapter on the valve
stem.
1-1/16" (27 mm) –
1-9/16" (40 mm)
Thick Wall: Use the #2 adapter and
the 1-3/8” (35 mm) screw.
9Fit the faceplate over the plate
assembly with the notch down.
8Secure the plate assembly to the
valve with proper length screws.
Do not overtighten.
7Secure the valve stem adapter
with the proper length screw.
6To adjust position, remove the
handle and valve stem adapter.
Turn the spline adapter.
3-way valve: Water should flow from
the main shower accessory with the
handle position at 12 o’clock.
10 Point the handle down. Thread
the bonnet onto the hub.
1266042-2-A

FIVE-YEAR LIMITED WARRANTY
All Kallista products carry Kallista's five-year limited warranty
unless otherwise noted.*
Kallista products are warranted to be free of defects in material
and workmanship for five years from the date of installation.
Kallista will, at its election, repair, replace, or make appropriate
adjustment where Kallista inspection discloses any such defects
occurring in normal usage within five (5) years after installation.
Kallista is not responsible for removal or installation costs.
Damages due to improper handling, installation or maintenance
are not considered manufacturing defects and are not covered
by this warranty. This warranty is valid for the original consumer
purchaser only. Use of in-tank toilet cleaners will void the
warranty.
To obtain warranty service, contact your Kallista Authorized
Showroom.
IMPLIED WARRANTIES INCLUDING THAT OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY. KALLISTA AND/OR
SELLER DISCLAIMS ANY LIABILITY FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Some
states/provinces do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of special, incidental
or consequential damages, so these limitations and exclusions
may not apply to you. This warranty gives you specific legal
rights. You may also have other rights which vary from
state/province to state/province.
This is Kallista's exclusive written warranty.
* Kallista's Hampstead and Stafford vitreous products, stainless
steel accessories, and wooden accessories carry a one-year
Limited Warranty.
Questions? Problems? For additional assistance, please contact
KALLISTA's Customer Service Department at 1-888-4-KALLISTA
(1-888-452-5547) or kallista.com.
1266042-2-A© 2015 KALLISTA

Installation Guide
Three-Way Transfer Valve
P29513, P29514
1091987-2-B

Thank You For Choosing Kallista
We appreciate your commitment to KALLISTA quality products. Please
take a moment to review this manual before you install your
KALLISTA product. If you encounter any installation or performance
problems, please do not hesitate to contact us from within the USA or
Canada at 1-888-4-KALLISTA (1-888-452-5547).
Tools and Materials
Before You Begin
IMPORTANT! Risk of product damage. Do not apply direct heat
to the transfer valve body. Excessive heat will damage the plastic
valve components and plaster guard.
Observe all local plumbing and building codes.
Do not remove the plaster guard from the transfer valve until
instructed to do so.
A mixed water supply is required for this transfer valve.
Do not plug any outlets on this transfer valve. The transfer valve
is not intended to be used as a shut-off valve.
If less than three accessories will be installed, connect the unused
transfer valve port to one of the accessories. All outlet ports must
be connected to an accessory, even if one accessory is connected
to two transfer valve outlet ports.
Carefully plan the installation before beginning. Carefully read
the entire instructions. Component location, spacing, and
situational requirements can vary.
Shut off the main water supply.
Plus:
• 1/2" Piping or Copper
Tubing for Outlets
• 3/4" Piping or Copper
Tubing for Inlets
Tubing
Cutter
Solder
Thread
Sealant Propane Torch
Bladed
Screwdriver
Adjustable
Wrench
1091987-2-B 2 Kallista

Before You Begin (cont.)
Inspect the waste and supply tubing; replace if necessary.
KALLISTA reserves the right to make revisions in the design of
products without notice, as specified in the Price Book.
Kallista 3 1091987-2-B

1. Prepare the Site
Provide a 2-7/8″(73 mm) to 3-1/8″(79 mm) diameter hole in the
wall material for the plaster guard.
2. Route and Connect the Water Supply
Route the 3/4″mixed water supply line to the transfer valve
location.
Apply thread sealant to the inlet port threads and connect the
water supply to the transfer valve inlet.
Plaster Guard
Max
Finished
Wall
Min
Finished
Wall
2-3/4"
(70 mm)
3-7/8" (98 mm)
Mixed Water
Supply 3/4"
Copper Tubing
or Piping
1091987-2-B 4 Kallista