Kallista P23105-LV User manual

INSTALLATION INSTRUCTIONS
Bidet Faucet
1087125_2_B
1 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P23105-LV P24406-LVP24406-CR

INSTALLATION INSTRUCTIONS
Bidet Faucet
1087125_2_B
2 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
ThANk YOU FOR ChOOSINg kALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual be-
fore you install your Kallista product. If you encounter any installation or performance problems, please do not
hesitate to contact us at the phone number listed at the bottom of the page.
BeFORe YOU BegIN
The appearance of your product may differ from the illustrations shown in these instructions, however, the
installation procedure is the same.
Prior to installation, unpack the faucet and drain and inspect it for damage. If the product is damaged,
please contact Kallista immediately at the phone number listed at the bottom of the page.
Observe all local plumbing and building codes.
Shut off the main water supply.
Carefully inspect waste and supply tubing for any sign of damage.
Replace waste or supply tubing if necessary.
For new installations, install the faucet before installing the bidet.
Kallista reserves the right to make revisions in the design of plumbing products without notice, as specied 
in the Price Book.
TOOLS ANd MATeRIALS
Pipe
Wrench
Plumbers
Putty
Adjustable
Wrench
Thread
Sealant
Hacksaw or
Tubing Cutter
Channel
Lock Pliers
SPRAY ASSeMBLY INSTALLATION1.
Rubber
Washer
Metal
Washer
Nut
Spray Head
Flange
Shank
Bidet
Remove the spray head and flange.
Thread the nut, metal washer, and rubber washer to the bottom of the
shank.
Apply a ring of plumbers putty or other sealant according to the putty
manufacturer’s instructions.
From the underside of the bidet, insert the shank through the spray hole.
From the top of the bidet, thread the flange onto the shank.
Securely thread the spray head as far as it will go on to the shank.
Thread the flange until it is snug against the spray head.
Securely tighten the nut onto the shank with a wrench. Do not overtighten.
Remove any excess putty or sealant.

INSTALLATION INSTRUCTIONS
Bidet Faucet
1087125_2_B
3 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
LIFT ROd eSCUTCheON INSTALLATION2.
Brass
Washer
Escutcheon
Apply
Plumbers
Putty.
Washer
Nut
Apply a bead of plumbers putty or other sealant to the underside of the
escutcheon according to the putty manufacturer’s instructions.
Insert the escutcheon through the mounting hole from above.
From the underside of the bidet, slide the washer (tapered side up), brass
washer, and nut onto the escutcheon shank.
Securely tighten the nut with a wrench. Do not overtighten.
Remove any excess putty or sealant.
dRAIN INSTALLATION3.
Apply plumbers
putty.
Flange
Gasket
Washer
Nut
Drain Body
Remove the protective cover from the flange.
Apply a ring of plumbers putty or other sealant to the underside of the flange 
according to the putty manufacturer’s instructions.
Assemble the nut, flat washer, and tapered gasket (tapered side up) fully onto 
the body.
From the underside of the xture, insert the drain body up into the drain hole.
From the top of the xture, securely hand tighten the flange onto the drain 
body.
Make sure the drain body seal hole is facing the back of the xture, and 
securely tighten the nut.
Remove any excess putty or sealant.
COMPLeTe dRAIN INSTALLATION4.
Body
Rod
Clip
Stopper
Nut
Flange
Nut
Tailpiece
Apply
thread
sealant.
Thumb
Screw
Stopper Rod
Link
Insert the stopper into the flange.
For regular installations, insert the short end of the rod into the body
seal hole and under the stopper. For vandal-resistant installations, t
the rod through the hole in the stopper. Hand tighten the body nut.
Remove and adjust the stopper as needed so it lifts about 3/8” (1 cm)
when opened. To adjust, rotate the threaded stopper rod in or out as
needed. Retighten the stopper nut.
Apply thread sealant tape to the tail piece threads, and thread the tail
piece to the body. Tighten the tail piece securely.
Slide one end of the clip on to the rod. Slide the link onto the rod with
the thumb screw facing the back of the xture.

INSTALLATION INSTRUCTIONS
Bidet Faucet
1087125_2_B
4 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
hANdLe VALVe INSTALLATION5.
Nut
Washer
Spacer
Hose with
compression fitting Hose with quick
connect fitting
Escutcheon
Install O-ring
Ensure that the O-ring is installed in the underside of the escutcheon.
Remove the washers and nuts from the valve assemblies.
Insert the valve assembly hoses through the mounting holes from the
top of the bidet. Make sure the valve assembly marked “COLD” is
installed in the right-hand hole (as viewed from the front of the bidet).
Loosely install the spacers, washers, and nuts to the bottom of the
valve assemblies.
Rotate the valve assemblies so that the handles are oriented as
desired in the off position.
Firmly hold the valve assemblies in place and then securely tighten
the nuts with a wrench. Do not overtighten.
Connect the quick connect ttings to the quick connect tee inlets. Do 
not use thread sealant. Loop the hoses to avoid kinking them.
VALVe/BReAkeR INSTALLATION6.
Adapter
Nut
Compression Sleeve
Sealing
Washer
Transfer
Valve
Apply
Thread
Sealant.
Apply
Thread
Sealant.
Plastic
Flexible
Hose
Pipe Fitting
Adapter
Slide the nut and compression sleeve onto the adapter.
Apply thread sealant onto the bottom threads of the adapter. Thread the
adapter onto the bottom of the transfer valve shank. Securely tighten
the nut.
Apply thread sealant onto the short end threads of the pipe tting. 
Thread the pipe tting onto the side of the transfer valve shank.
Apply thread sealant onto the long end threads of the pipe tting. 
Thread the flexible hose onto the pipe tting.
Slide the sealing washer (tapered side up) onto the transfer valve.
From the underside of the bidet, insert the transfer valve into the
mounting hole.
From the front of the bidet, rotate the transfer valve until the pipe tting 
faces toward the right.
From the top of the bidet, slide a sealing washer (tapered side down),
flat washer, and plastic nut onto the transfer valve. Securely hand
tighten the plastic nut.
From the front of the bidet, rotate the valve stem counterclockwise.
Slide the spline insert onto the valve stem.
Thread the escutcheon onto the plastic nut.
Rotate the handle until the pointer faces the front of the bidet. Press the
handle onto the spline insert.

INSTALLATION INSTRUCTIONS
Bidet Faucet
1087125_2_B
5 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
FLeXIBLe hOSe INSTALLATION7.
Spray Head
Assembly
Shank
Apply
Thread
Sealant.
Plastic
Flexible
Hose
Transfer Valve/
Vacuum Breaker
End Body
Valve
Gasket
Supply
Tee
Nylon
Washer
Rubber
Gasket
Quick-
Connect
Fittings
Apply thread sealant onto the threads of the spray shank.
Connect the flexible hose from the transfer valve onto the
spray shank.
Connect the supply hoses to the supply tee via the quick-
connect ttings.
Insert a rubber gasket and nylon washer into the supply tee
outlet.
Thread a flexible hose into the supply tee outlet.
Slide the gasket onto the transfer valve/vacuum breaker
shank.
Connect the flexible hose from the supply tee outlet onto the 
transfer valve/vacuum breaker shank.
SUPPLY CONNeCTIONS8.
Supply Hose
Supply Hose
Connect the supply hoses from the valve assemblies to the supply
stops. (Left is hot - right is cold).
Tighten all connections.
INSTALLATION CheCkOUT9.
Spray Head
Spray
Assembly
Connect the tailpiece to the P-trap (as needed).
Ensure that all connections are tight.
Open the drain.
Turn on the main water supply and check for leaks. Repair as needed.
Remove the spray head.
Open both the hot and cold valves and run water through the transfer valve and spray
assembly for about a minute to remove debris. Check for leaks.
Turn off the water.
Reinstall the spray head.