Kantech KT-PC4216 User manual

Tel.: [phone] •Toll Free: 1 888 222-1560 •Fax: [phone] •Internet: www.kantech.com DN1247-0404
Copyright 2004 Kantech Systems. All rights reserved •Specifications may change without notice.
Kantech Systems
KT-PC4216
Output Module
/
1. Introduction
The KT-PC4216 is an open collector to 12 VDC 16 zones output module. It can
be used for elevator access control (may require additional hardware).
2. Specifications
• 16 outputs low current module, 12V, 50mA max. each, power drawn from
Combus (since Combus can handle a maximum of 500mA, a KT-PC4204
module in “repower” mode can be used to increase the current of the
Combus of 1 Amp)
• Connects to KT-300 via 4-wire Combus
• Nominal current draw of 15mA (from Combus)
• Tamper contact input
• Can be used for elevator access control
3. Installing the KT-PC4216
3.1. Unpacking
The KT-PC4216 package should include the following parts/items:
• One (1) KT-PC4216 circuit board
• Four (4) plastic standoffs
• One (1) installation instructions sheet
3.2. Mounting
The KT-PC4216 should be located inside a compatible cabinet (Kantech part no.
KT-4051CAB), mounted in a dry, secure location. Preferably, it should be placed
at a convenient distance from the connected devices.
Perform the following steps to mount the unit:
1. Press the four (4) plastic standoffs through the mounting holes at back of
the cabinet,
2. Secure the cabinet to the wall in the desired location. Use appropriate wall
anchors when securing the cabinet to drywall, plaster, concrete, brick or
other surfaces,
3. Press the circuit board into the plastic standoffs to secure the module to the
cabinet.
Once the unit is mounted, wiring may be started.
3.3. Installation and Wiring
Before beginning to wire the unit, ensure that all power (AC transformer and
battery) is disconnected from the controller.
Perform the following steps to complete wiring:
1. Connect the four Combus wires to the KT-PC4216. Connect the red, black,
yellow and green Combus wires to the RED, BLK, YEL and GRN
terminals, respectively.
2. Complete all output wiring as illustrated below:
Note: Current is drawn from the combus.
Note: May require a KT-PC4204 power supply module if drawing too much
current from the Combus.
3. Connect the external tamper switch, if used.
Consult the wiring diagrams for further information.
3.4. Applying Power
After all wiring is completed, apply power to the KT-300 controller. Connect the
battery leads to the battery, then connect the AC transformer.
Note: Do not connect the power until all wiring is complete.

Tel.: [phone] •Toll Free: 1 888 222-1560 •Fax: [phone] •Internet: www.kantech.com DN1247-0404
Copyright 2004 Kantech Systems. All rights reserved •Specifications may change without notice.
Kantech Systems
KT-PC4216
Output Module
4. Assigning the module
Follow the instructions below for assigning and programming your KT-PC4216
module.
Follow these steps to assign the module(s):
1. Establish communication between the PC and the controller,
2. Remove the tamper switch wire (or only the wire if tamper switch is not
used),
3. A serial number should be displayed on the screen, in the same window
where is the serial number is located, you should see the type of module and
on which controller it is connected,
4. From the software, select the functionality of the module and enter the serial
number in the appropriate field (see your software reference manual under
controller definition -- Assigning modules for more details).
Note: Don’t forget to reconnect the tamper switch (or the wire, if there is
no tamper switch).
Terminal Connections
Module no.: ______________________________________________________________________________________
Date of installation: _______________________________________________________________________________
KT-300 Name: ____________________________________________________________________________________
KT-300 SITE NAME: _______________________________________________________________________________
KT-300 Serial Number: _____________________________________________________________________________
COMBUS (FROM):_________________________________________________________________________________
COMBUS (TO): ___________________________________________________________________________________
Z1: _____________________________________________________________________________________________
Z2: _____________________________________________________________________________________________
Z3: _____________________________________________________________________________________________
Z4: _____________________________________________________________________________________________
Z5: _____________________________________________________________________________________________
Z6: _____________________________________________________________________________________________
Z7: _____________________________________________________________________________________________
Z8: _____________________________________________________________________________________________
Z9: _____________________________________________________________________________________________
Z10: ____________________________________________________________________________________________
Z11: ____________________________________________________________________________________________
Z12: ____________________________________________________________________________________________
Z13: ____________________________________________________________________________________________
Z14: ____________________________________________________________________________________________
Z15: ____________________________________________________________________________________________
Z16 _____________________________________________________________________________________________
FCC & IC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Kantech Systems Inc. could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart
“B” of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared
by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office,
Washington, D.C. 20402, Stock # 004-000-00345-4. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. This class
B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. The KT-300 is also compliant with EN55022: 1994, amendment 1:
1995, Class B.