Kargo Master 30070 User manual

Installation Guide
30070
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
[e-mail]
DATE: ______________

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 1
Installation Instructions –30070
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT*
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
Tools Needed
7/32” Allen
9/16” Wrench and Socket
3/16” Allen
1/2” Wrench and Socket
Table of Contents
Parts List ................................................................................................................................... 2
Hardware List ........................................................................................................................ 2-3
Step 1 Leg to Bedrail ................................................................................................................ 4
Step 2 Install Bedrail and Leg Assembly ................................................................................... 5
Step 3 Install Crossbar ............................................................................................................. 6
Step 4 Mount Bedrails ............................................................................................................. 6
Stake Pocket ................................................................................................................. 7
Under Bed Rail .............................................................................................................. 8
Slot Rail .................................................................................................................... 9-10
Before You Begin
•Read all instructions.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
Installation Instructions –30070
Parts
Hardware

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Installation Instructions –30070
Hardware Con’t

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
Installation Instructions –30070
Step 1 –Leg to Bedrail
•Bolt leg assembly (A) to each bedrail (B&C) using four 3/8” x 1” plow bolts (6), four 3/8” flat
washers (7) and four 3/8” nyloc nuts (8) in the oreintation shown.
•Repeat for each of the four legs, leg on two different bed rails.
•Be sure the bend in the leg assembly is towards the bend in the bed rail as shown.
•SNUG TIGHTEN, BUT ALLOW MOVEMENT.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Installation Instructions –30070
Step 2 –Install Bedrail and Leg Assembly
•Place a bedrail with leg assembly in each corner of the bed.
•Have the majority of the bedrail towards the center of the bed.
•Have the bend in the legs towards the center of the cab.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
Installation Instructions –30070
Step 3 –Install Crossbar
•Slide crossbar in through the top of each leg.
•Be sure there is equal distance from the leg to the end of the crossbar while maintaining a flat
bed rail mount.
•Some beds are more narrow in the rear than in the front. The equal distance on the crossbar
may vary from front to back.
•DO NOT TIGHTEN AT THIS POINT.
Step 4 –Mount Bedrails
•There are multiple ways to mount the bedrail depending on which truck you have.
•Some trucks have stake pockets and some trucks have a slot rail on the inside of the bed.
•One may use the under side of the bed if accessible as well.
•See next pages for various types of installations.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
Installation Instructions –30070
Step 4A –Stake Pocket
•Find stake pocket on bed rail. In some situations, the plastic needs to be cut out to expose the
metal stake pocket.
•Place a 3/8” x 2-1/2” button head (5) through the hole in the top of the bed rail (B & C). Attach
to the chevy nut (10) and place down inside of the stake pocket.
•When installing, have the chevy nut come into contact with metal inside the stake pocket.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Installation Instructions –30070
Step 4B –Under Bed Rail
•Find location where the underside of bed rail is accessible. Try and pick up two locations.
•Use 3/8” x 2-1/2” button head (5) and an angle mount (13) to clamp under bed rail.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Installation Instructions –30070
Step 4C –Slot Rail
•If the truck is equipped with a slot rail on the inside of the bed, make use of a weldment (11 or
12).
•Determine which weldment will work with the rail based on the width of the rail.
•Slide either small weldnut (11) or large pemstud (12) into slot rail and under the slots in the bed
rail.
•If using the small weldnut, bolt using a 5/16” x 1” button head (1), a 5/16” split lock washer (2)
and a 5/16” flat washer (3).