Katadyn 8013631 User manual

Mini Water Microfilter
(Model #8013631)
Mini Replacement Cartridge
(Model #8013632)
(6)
When You Travel Abroad, Camp or Backpack…
…you run a risk of illness ranging from the inconvenience and discomfort of diarrhea to
more serious illnesses caused by protozoan cysts (i.e., Legionella, Giardia,
Cryptosporidium), viruses and bacteria.
The microorganisms that cause these diseases are often found in the food and water you
consume. Lakes, streams and the local water supply may be contaminated.
To minimize the risk of contracting these illnesses, we suggest that you consult with your
physician, state health department or travelers' clinic 4-6 weeks before you depart.
And while you are traveling…
" Make sure that prepared food is thoroughly cooked.
" Select non-cooked foods (fruits, nuts, etc.) that have intact shells or skins, and
clean your hands before peeling the food.
" Wash your hands with soap and water thoroughly and often, especially
before you eat. Filter all drinking water with your Katadyn Mini Water
Microfilter.
The Katadyn Mini Microfilter is an essential piece of outdoor equipment. For questions or
suggestions, please contact us.
(5)
Long-Term Storage (After Your Trip is Over)
Store the Mini filter as follows:
1) Remove ceramic filter and brush it under running water with the supplied cleaning pad.
Allow to air-dry completely.
2) Put ceramic filter back into housing.
3) Grease o-rings with silicone lubricant provided.
4) Stow input hose inside pump body and store Mini inside the carry bag.
Note: When removing unit from long-term storage, flush the system with one liter of water to
remove any stale tasting water.
Ceramic Capacity
Ceramic capacity depends on water quality. The dirtier the water the more often you will
have to clean the element. This reduces the capacity of approx. 2'000 gallons (7'000 liters).
2-3) Inspect the ceramic for cracks after cleaning, if you dropped the filter or if you had
freezing temperatures. If the filter shows cracks it will no longer protect you from
microorganisms.
Ceramic Installation
Replacement filter elements are available from the dealer where you purchased your
Katadyn Mini.
1) Remove output hose from output barb. Remove the element by turning it
counterclockwise as far as it will go and lifting it from the housing.
2) Remove new ceramic element from packaging.
3) Insert new ceramic housing by holding output barb towards you and turning
clockwise as far as it will go while pushing down.
4) Re-attach output hose to output barb.
5) Flush ceramic element by pumping and discarding the first liter.
Product Registration
Please take a moment to register your new Katadyn product by completing the short product
registration form online at www.katadyn.com/productregistration. The information you
provide will enable us to better serve you with products developed to meet your needs and
interests. Register your Katadyn product online and you will be automatically entered into a
drawing to win a free Katadyn product.
Limited Warranty
Your Katadyn Mini Microfilter is warranted for one (1) year from the date of purchase
against defects in materials and workmanship. Should your Katadyn Mini prove defective
within one year from the date of purchase, return it to the Katadyn retailer from whom it
was purchased. If you have any questions please contact Katadyn in Europe
[phone], in North America 1-800-755-6701. Katadyn, at its discretion, will
replace or repair the damaged item. Please retain your purchase receipt as proof of date
purchased. This warranty gives you specific legal rights and you may have other legal rights
which vary from state to state.
Contact North America:
Katadyn North America Inc.
4830 Azelia Avenue North
Minneapolis, MN 55429 / USA
1-800-755-6701
[email protected] / www.katadyn.us
Contact International:
Katadyn Products Inc.
Pfäffikerstrasse 37
8310 Kemptthal / Switzerland
[email protected] www.katadyn.com
In Europe [phone], in North America 1-800-755-6701.
Print No.100550 /
If the gap of the measuring gauge fits over the ceramic it is time to replace the filter. (Figure
Mini Water Microfilter
(Model #8013631)
Mini Replacement Cartridge
(Model #8013632)
(6)
When You Travel Abroad, Camp or Backpack…
…you run a risk of illness ranging from the inconvenience and discomfort of diarrhea to
more serious illnesses caused by protozoan cysts (i.e., Legionella, Giardia,
Cryptosporidium), viruses and bacteria.
The microorganisms that cause these diseases are often found in the food and water you
consume. Lakes, streams and the local water supply may be contaminated.
To minimize the risk of contracting these illnesses, we suggest that you consult with your
physician, state health department or travelers' clinic 4-6 weeks before you depart.
And while you are traveling…
" Make sure that prepared food is thoroughly cooked.
" Select non-cooked foods (fruits, nuts, etc.) that have intact shells or skins, and
clean your hands before peeling the food.
" Wash your hands with soap and water thoroughly and often, especially
before you eat. Filter all drinking water with your Katadyn Mini Water
Microfilter.
The Katadyn Mini Microfilter is an essential piece of outdoor equipment. For questions or
suggestions, please contact us.
(5)
Long-Term Storage (After Your Trip is Over)
Store the Mini filter as follows:
1) Remove ceramic filter and brush it under running water with the supplied cleaning pad.
Allow to air-dry completely.
2) Put ceramic filter back into housing.
3) Grease o-rings with silicone lubricant provided.
4) Stow input hose inside pump body and store Mini inside the carry bag.
Note: When removing unit from long-term storage, flush the system with one liter of water to
remove any stale tasting water.
Ceramic Capacity
Ceramic capacity depends on water quality. The dirtier the water the more often you will
have to clean the element. This reduces the capacity of approx. 2'000 gallons (7'000 liters).
2-3) Inspect the ceramic for cracks after cleaning, if you dropped the filter or if you had
freezing temperatures. If the filter shows cracks it will no longer protect you from
microorganisms.
Ceramic Installation
Replacement filter elements are available from the dealer where you purchased your
Katadyn Mini.
1) Remove output hose from output barb. Remove the element by turning it
counterclockwise as far as it will go and lifting it from the housing.
2) Remove new ceramic element from packaging.
3) Insert new ceramic housing by holding output barb towards you and turning
clockwise as far as it will go while pushing down.
4) Re-attach output hose to output barb.
5) Flush ceramic element by pumping and discarding the first liter.
Product Registration
Please take a moment to register your new Katadyn product by completing the short product
registration form online at www.katadyn.com/productregistration. The information you
provide will enable us to better serve you with products developed to meet your needs and
interests. Register your Katadyn product online and you will be automatically entered into a
drawing to win a free Katadyn product.
Limited Warranty
Your Katadyn Mini Microfilter is warranted for one (1) year from the date of purchase
against defects in materials and workmanship. Should your Katadyn Mini prove defective
within one year from the date of purchase, return it to the Katadyn retailer from whom it
was purchased. If you have any questions please contact Katadyn in Europe
[phone], in North America 1-800-755-6701. Katadyn, at its discretion, will
replace or repair the damaged item. Please retain your purchase receipt as proof of date
purchased. This warranty gives you specific legal rights and you may have other legal rights
which vary from state to state.
Contact North America:
Katadyn North America Inc.
1-800-755-6701
[email protected] / www.katadyn.com
Contact International:
Katadyn Products Inc.
Birkenweg 4
8304 Wallisellen / Switzerland
[email protected] / www.katadyn.ch
In Europe [phone], in North America 1-800-755-6701.
6325 Sandburg Road
Minneapolis, MN 55427 / USA
Print No.100550 /
If the gap of the measuring gauge fits over the ceramic it is time to replace the filter. (Figure
(Model #8013631 + 8017764)
(Model #8013631 + 8017764)
Print No. 100550/4
Print No. 100550/4

Key Components
(1) (2) (3) (4)
Field Performance Tips
The Katadyn Mini is designed to remove bacteria and protozoan cysts
such as Legionella, Giardia and Cryptosporidium. To extend ceramic life, always
use the best water source available. Keep the intake prefilter clean and off the bottom. In
heavy sediment conditions, wrap a coffee filter or bandanna around the intake prefilter.
Where possible, place untreated water in container and wait for sediment to settle out until
water appears clear - then filter from water above the sediment.
Maintain your Katadyn water system to keep it operating smoothly.
1) If handle is hard to push
Clogged filter pores. If the filter pores of the ceramic are clogged the ceramic
needs to be cleaned. Never use force when pumping. Remove the element by turning
it counterclockwise as far as it will go and lifting it from the housing.
Regenerate the ceramic by brushing under running water with the supplied cleaning
pad until the light, original ceramic color appears again. When reassembling hold
output barb towards logo on pump housing and turn clockwise as far as it will go
while pushing down.
Lubricate pump handle o-ring. Silicone lubricant is provided with your new
unit. Remove handle collar and handle. (Figure 1-1) Clean excess build-up from
black rubber o-ring on bottom of handle. Place a small amount of silicone lubricant
all the way around the o-ring. Reassemble.
2) If unit pumps easily, but no water flow:
Make sure prefilter is submerged.
Make sure that intake hose is not blocked or pinched.
Hold the filter vertically until water flows.
3) Prefilter: Rinse the prefilter in water to remove any particles that may be caught
in the strainer.
4) Storage: Your Katadyn water system comes with a carry bag for storage. To pre-
vent the possibility of cross contamination, stow input hose inside pump body to
avoid contact with the output hose.
(Figure 1-1)
Pump Handle
Output Barb
Ceramic Element
Housing
Base Cover
Input Barb
(inside housing)
Handle Collar
Pump Handle O-Ring
Measuring Gage
Input Hose with Prefilter
Product Set-up
The Mini requires minimal set up. For best results, try out the Mini before first field use to
familiarize yourself with its operation.
1) Connect Hoses
Open the base cover at the lower end of the housing and remove the input hose (hose
with prefilter) from the input barb inside the housing. Attach the hose float (approx. 2
inches from prefilter). Reconnect the input hose to the input barb. An optional output
hose (included) can be attached to the output barb for added convenience.
(Figure 1-1, 2-1, 2-2)
2) Flush System
Important: Before first use, flush system by pumping approximately 0.5 liters of water
through the unit to remove harmless ceramic dust. See following section on Normal
Operation on how to filter water.
Normal Operation
1) Place input hose in untreated water source. Adjust the float to keep prefilter off the
bottom and away from sediment.
2) Place the output hose into a clean water container*. (Figure 2-2)
3) Hold the filter vertically and begin pumping the handle in a slow, steady manner.
Make sure the input hose is not kinked.
4) After filling water container with filtered water, remove output hose from container
and input hose from water source. Continue pumping to remove remaining water
5) Stow input hose inside pump body and store Mini inside the carry bag.
*Note: Before each use, flush and discard a small amount (5 - 10 strokes) of water
to remove stale taste.
(Figure 2-1)
X > Z
X > Z
Z
Z
X
X
(Figure 2-2)
(Figure 2-3)
Float
Input Hose
Prefilter
Output Hose
Output Barb
Ceramic Element
Measuring Gage
Thank you for choosing a Katadyn portable water microfiltration
for reduction of bacteria (99.9999% Klebsiella terrigena) and
protozoan cysts (99.9% Giardia and Cryptosporidium). As the
smallest and lightest ceramic filter from Katadyn the Mini is ideal for
light solo use during travel and day-hiking.
system. The Katadyn Mini Microfilter meets industry standards
from pump body.
Key Components
(1) (2) (3) (4)
Field Performance Tips
The Katadyn Mini is designed to remove bacteria and protozoan cysts
such as Legionella, Giardia and Cryptosporidium. To extend ceramic life, always
use the best water source available. Keep the intake prefilter clean and off the bottom. In
heavy sediment conditions, wrap a coffee filter or bandanna around the intake prefilter.
Where possible, place untreated water in container and wait for sediment to settle out until
water appears clear - then filter from water above the sediment.
Maintain your Katadyn water system to keep it operating smoothly.
1) If handle is hard to push
Clogged filter pores. If the filter pores of the ceramic are clogged the ceramic
needs to be cleaned. Never use force when pumping. Remove the element by turning
it counterclockwise as far as it will go and lifting it from the housing.
Regenerate the ceramic by brushing under running water with the supplied cleaning
pad until the light, original ceramic color appears again. When reassembling hold
output barb towards logo on pump housing and turn clockwise as far as it will go
while pushing down.
Lubricate pump handle o-ring. Silicone lubricant is provided with your new
unit. Remove handle collar and handle. (Figure 1-1) Clean excess build-up from
black rubber o-ring on bottom of handle. Place a small amount of silicone lubricant
all the way around the o-ring. Reassemble.
2) If unit pumps easily, but no water flow:
Make sure prefilter is submerged.
Make sure that intake hose is not blocked or pinched.
Hold the filter vertically until water flows.
3) Prefilter: Rinse the prefilter in water to remove any particles that may be caught
in the strainer.
4) Storage: Your Katadyn water system comes with a carry bag for storage. To pre-
vent the possibility of cross contamination, stow input hose inside pump body to
avoid contact with the output hose.
(Figure 1-1)
Pump Handle
Output Barb
Ceramic Element
Housing
Base Cover
Input Barb
(inside housing)
Handle Collar
Pump Handle O-Ring
Measuring Gage
Input Hose with Prefilter
Product Set-up
The Mini requires minimal set up. For best results, try out the Mini before first field use to
familiarize yourself with its operation.
1) Connect Hoses
Open the base cover at the lower end of the housing and remove the input hose (hose
with prefilter) from the input barb inside the housing. Attach the hose float (approx. 2
inches from prefilter). Reconnect the input hose to the input barb. An optional output
hose (included) can be attached to the output barb for added convenience.
(Figure 1-1, 2-1, 2-2)
2) Flush System
Important: Before first use, flush system by pumping approximately 0.5 liters of water
through the unit to remove harmless ceramic dust. See following section on Normal
Operation on how to filter water.
Normal Operation
1) Place input hose in untreated water source. Adjust the float to keep prefilter off the
bottom and away from sediment.
2) Place the output hose into a clean water container*. (Figure 2-2)
3) Hold the filter vertically and begin pumping the handle in a slow, steady manner.
Make sure the input hose is not kinked.
4) After filling water container with filtered water, remove output hose from container
and input hose from water source. Continue pumping to remove remaining water
5) Stow input hose inside pump body and store Mini inside the carry bag.
*Note: Before each use, flush and discard a small amount (5 - 10 strokes) of water
to remove stale taste.
(Figure 2-1)
X > Z
X > Z
Z
Z
X
X
(Figure 2-2)
(Figure 2-3)
Float
Input Hose
Prefilter
Output Hose
Output Barb
Ceramic Element
Measuring Gage
Thank you for choosing a Katadyn portable water microfiltration
for reduction of bacteria (99.9999% Klebsiella terrigena) and
protozoan cysts (99.9% Giardia and Cryptosporidium). As the
smallest and lightest ceramic filter from Katadyn the Mini is ideal for
light solo use during travel and day-hiking.
system. The Katadyn Mini Microfilter meets industry standards
from pump body.