Kathrein 742270V03 User manual

742270V03 Page 1 of 4
6-Port Antenna
Frequency Range
Dual Polarization
HPBW
Adjust. Electr. DT
set by hand or by optional RCU (Remote Control Unit)
1710–1880790–960 1920–2170
XX X
65°65° 65°
0°–8°0°–14° 0°–8°
B1
B1
R1
R1
B2
B2
936.4896/a ngmn 04.19.02.01 Subject to alteration.
6-Port Antenna 790–960/1710–1880/1920–2170 65°/65°/65° 15/17/17dBi 0°–14°/0°–8°/0°–8°T
Type No. 742270V03
Low band
R1, connector 1–2
R1, connector 1–2
790–960
Frequency Range MHz 790 – 862 824 – 894 880 – 960
Gain at mid Tilt dBi 14.3 14.5 14.6
Gain over all Tilts dBi 14.3 ± 0.2 14.4 ± 0.3 14.6 ± 0.3
Horizontal Pattern:
Azimuth Beamwidth ° 69 ± 1.0 68 ± 1.6 67 ± 1.0
Front-to-Back Ratio,
Total Power, ± 30° dB > 25 > 26 > 27
Cross Polar Discrimination
at Boresight dB > 24 > 25 > 26
Cross Polar Discrimination
over Sector dB > 13.5 > 13.0 > 12.5
Azimuth Beam
Port-to-Port Tracking dB < 1.0 < 1.0 < 1.5
Vertical Pattern:
Elevation Beamwidth ° 16.8 ± 0.5 16.4 ± 0.9 15.6 ± 0.9
Electrical Downtilt
continuously adjustable ° 0.0 – 14.0
Tilt Accuracy ° < 0.6 < 0.5 < 0.7
First Upper Side Lobe
Suppression dB > 15 > 17 > 18
Cross Polar Isolation dB > 30
Port to Port Isolation dB > 45 (R1 // B1 // B2)
Max. Effective Power
per Port W 300 (at 50 °C ambient temperature)
Max. Effective Power
Port 1–2 W 600 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

Page 2 of 4 742270V03
936.4896/a ngmn 04.19.02.01 Subject to alteration.
6-Port Antenna
High bands
B1, connector 3–4
B1, connector 3–4
B2, connector 5–6
B2, connector 5–6
1710–1880 1920–2170
Frequency Range MHz 1710 – 1880 1920 – 2170
Gain at mid Tilt dBi 17.1 17.1
Gain over all Tilts dBi 17.0 ± 0.4 17.0 ± 0.5
Horizontal Pattern:
Azimuth Beamwidth ° 62 ± 3.1 60 ± 3.6
Front-to-Back Ratio,
Total Power, ± 30° dB > 28 > 24
Cross Polar Discrimination
at Boresight dB > 26 > 25
Cross Polar Discrimination
over Sector dB > 12.5 > 13.0
Azimuth Beam
Port-to-Port Tracking dB < 0.5 < 1.5
Vertical Pattern:
Elevation Beamwidth ° 7.5 ± 0.3 6.8 ± 0.6
Electrical Downtilt
continuously adjustable ° 0.0 – 8.0 0.0 – 8.0
Tilt Accuracy ° < 0.3 < 0.3
First Upper Side Lobe
Suppression dB > 16 > 15
Cross Polar Isolation dB > 30
Port to Port Isolation dB > 45 (R1 // B1 // B2)
> 30 (B1 // B2)
Max. Effective Power
per Port W 150 (at 50 °C ambient temperature)
Max. Effective Power
Port 3–4, Port 5–6 W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

742270V03 Page 3 of 4
2)
1)
1384 | 54.5 1417 | 55.8 1455 | 57.3
Adjustment mechanism
with integrated scale
All dimensions
in mm | inches
1) 9 | 0.4
2) 64 | 2.5
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Material: Reflector screen: Weather-proof aluminum.
Fiberglass housing: It covers totally the internal antenna components.
The special design reduces the sealing areas to a minimum and
guarantees the best weather protection. Fiberglass material guarantees
optimum performance with regards to stability, stiffness, UV resistance
and painting. The color of the radome is light grey.
All screws and nuts: Stainless steel or hot-dip galvanized steel.
Grounding: The metal parts of the antenna including the mounting and the inner
conductors are DC grounded.
6-Port Antenna
936.4896/a ngmn 04.19.02.01 Subject to alteration.
Electrical specifications, all systems
Impedance Ω 50
VSWR < 1.5
Return Loss dB > 14
Interband Isolation dB > 30
Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)
Polarization ° +45, –45
Max. Effective Power
for the Antenna W900 (at 50 °C ambient
temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 6 x 7-16 female long neck
Connector Position bottom
Adjustment Mechanism 3x, Position bottom
continuously adjustable
Wind load
(at Rated Wind
Speed: 150 km/h)
N | lbf Frontal 600 | 135
Lateral 270 | 61
Rearside 640 | 144
Max. Wind Velocity km/h
mph 241 150
Height / Width / Depth mm
inches 1384 / 261 / 146 54.5 / 10.3 / 5.7
Category of
Mounting Hardware M (Medium)
Weight kg
lb 19.0 / 21.2 (clamps incl.) 41.9 / 46.7 (clamps incl.)
Packing Size mm
inches 1696 / 282 / 182 66.8 / 11.1 / 7.2
Scope of Supply Panel and 2 units of clamps
for 42–115 mm |
1.7–4.5 inches diameter
Accessories (order separately if required)
Type No. Description Remarks
mm | inches
Weight approx.
kg | lb
Units per
antenna
731651 1 clamp Mast diameter: 28 – 60 | 1.1 – 2.4 0.8 | 1.8 2
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
737978 1 downtilt kit Downtilt angle: 0° – 14.5° 2.3 | 5.1 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

Any previous data sheet issues have now become invalid.
Page 4 of 4 742270V03
6-Port Antenna
Correlation Table
Frequency range Array Connector
790–960 MHz R1 1–2
1710–1880 MHz B1 3–4
1920–2170 MHz B2 5–6
R1
B1
B2
1x
1
9
2
0
-
2
1
7
0
1
9
2
0
-
2
1
7
0
1
7
1
0
-
1
8
8
0
T
i
l
t
T
i
l
t
T
i
l
t
7
9
0
-
9
6
0
7
9
0
-
9
6
0
1
7
1
0
-
1
8
8
0
60 | 2.4
167 | 6.6
184 | 7.2
261 | 10.3 *
146 | 5.7 *
167 | 6.6 *
46 | 1.8
49 | 1.9
108 | 4.3
95 | 3.7
145 | 5.7
35 | 1.4
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Layout of interface:
936.4896/a ngmn 04.19.02.01 Subject to alteration.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

738546 Page 1 of 1
Mounting Hardware
Clamp Included in the Scope of Supply
936.3920/c Subject to alteration.
Suitable for mast diameter (mm)
[inches]
42 – 115
[1.65 – 4.53]
Antenna – mast distance (mm)
[inches]
20 – 25
[0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg)
[lb]
1.1
[2.43]
Please note: Kathrein does not recommend to use counter nuts.
The additional nuts supplied are only meant as spares.
All dimensions in mm and [inches]
152 [5.98]
100 [3.94] 40 [1.57]
72 [2.83]
35 [1.38]
64 [2.52]
125 [4.92]
40 [1.57]
20–25 [0.79–0.98]
42–115
[1.65–4.53]
M10 MA= 25 Nm
M8 MA= 20 Nm
20–25
[0.79–0.98]
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

Page 1 of 2
936.4137 Subject to alteration.
General Instructions
for Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
Manual adjustment procedure:
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Remove the protective cap.
➀Adjustment wheel with twist-lock
function.
➁Downtilt spindle with integrated
scale.
➀Thread for fixing the protective
cap or the RCU (Remote Control
Unit).
➁Gearwheel for RCU power drive.
To set the downtilt angle exactly,
you must look horizontally at the
scale. The lower edge of the gear-
wheel must be used for alignment.
Set downtilt angle by rotating the
adjustment wheel.
Screw on the protective cap again.
0° – max.°
0° – max.°
1
2
2
1
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com

Page 2 of 2
936.4137 Subject to alteration.
General Instructions for Feederline Installation
for Triple-band Antennas
Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To
tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool
(as shown below) in combination with a standard torque-wrench.
Description of bottom end cap (exemplary picture):
Installation of the feederline connector and RCU (optional):
In order to protect the adjustment mechanism the protective caps have to be attached during
feederline installation!
The sequence for installation is:
feederline no. 1, 2, 3, 4, 5, 6.
Carefully put the connector in
place and hand-screw the nut.
Use a torque-wrench to finish
installation (see installation tool).
Repeat operations as shown for
each feederline!
After feederline installation, the
optional remote control units
(RCU) 7, 8, 9 can be mounted if
required. For a full description
of RCU installation please refer
to the respective data sheet.
These tools are suitable for 7-16 connectors with a wrench
size of 27 or 32 mm.
Tighten nut within a torque range of 25 – 33 Nm depending
on connector manufacturers’ specifications.
Kathrein installation set: Type No. 85010005
Set has to be ordered separately!
Set consists of two spanners of 27 and 32 mm width.
27 or 32 mm
1/2ßsquare actuation according to
DIN 3120 Form C
There are six feederline connectors and three adjustment mechanisms
located at the bottom of the antenna.
8
7
9
65
1 2
34
Ventilation hole
Color coding:
Correlation of each RF input to:
– the corresponding adjustment
mechanism
– the frequency range
– the polarization
7-16 female (long neck)
Spindle with tilting scale
Adjustment mechanism
(protective cap removed)
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: [phone] Fax: [phone] Email: [email protected]
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com