KBL megaSun 5600 User manual

OPERATING INSTRUCTIONS

Copyright and Trademark
© Copyright 2018 KBL AG
This documentation only covers products manufactured by KBL AG. It must not be duplicated, photocopied,
translated or stored without prior specific permission by KBL AG. Duplication on electronic media or in machine-
readable form, either in whole or in part, is also prohibited.
is a registered trademark of KBL AG.
DISCLAIMER
All information given in this document correspond to the status quo at the date of publication but may be subject
to changes. Therefore, we do not accept any liability for, nor do we guarantee the accuracy and/or completeness
of the information.
EXPORT
Technical equipment and versions of the devices are in accordance with the legal prescriptions of the respective
country of destination. Export to the USA and Canada of the KBL products, listed in this guide, or operation of
the systems in these countries, are not permitted. KBL does not accept any manufacturers liability in case this
direction is not adhered to. It is expressly pointed out that any violation of the export/operation prohibition will
involve substantial risks of liability for the exporter and/or operator.
For instruction updates, please refer to http://www.kbl-support.de.
KBL AG
Ringstrasse 24-26 · 56307 Dernbach · Germany
Telephone [phone] · Fax [phone]
Email: [email protected] ·
www.megaSun.de
TRANSLATION OF THE ORIGINAL OPERATING INSTRUCTIONS
Version: BA_5600mod2010_GB_F
Date: 03/2018
Control / Software version: KBL 7 / 04.42
Item no: 0100036555
Tanning device name [tech.]: 4209

Operating Instructions |megaSun 5600
4
Contents
General information .............................................. 5
About these instructions ......................................... 5
Safety signs............................................................. 5
Signal words............................................................ 5
Transport by forklift truck ........................................ 6
Other modes of transport........................................ 6
Old equipment disposal .......................................... 6
Service..................................................................... 6
Updating system software ...................................... 6
Safety notes ........................................................... 7
Intended use............................................................ 7
Foreseeable misuse ................................................ 7
Duties of the operator ............................................. 8
General safety advice.............................................. 8
Timer operation ....................................................... 8
Tanning times .......................................................... 8
Description of the unit .......................................... 9
Standards................................................................ 9
Components............................................................ 9
Connections - Audio ........................................... 10
Level adjustment studio music signal ................... 10
Operation using different audio sources ............... 10
Bluetooth connection ............................................ 11
Start-up ................................................................ 13
Operating modes................................................... 13
Tanning instructions............................................ 14
Instructions for the user ........................................ 14
Tanning times ........................................................ 15
Tanning mode ...................................................... 16
Starting the tanning session.................................. 16
Operation during the tanning session ................... 16
Basic functions...................................................... 18
Variable section of the interior control panel......... 18
Standby mode / service mode ........................... 20
Layout of the interior control panel numbers ........ 20
Switching the decorative lighting on and off......... 20
aquaCool spraying test ......................................... 20
Invoking the service menu..................................... 20
Service menu - Basics .......................................... 21
Service menu - Overview ...................................... 23
Service codes........................................................ 24
Service menu - options ......................................... 24
Set decorative lighting........................................... 37
Maintenance and cleaning ................................. 38
Instructions on cleaning and care ......................... 38
Maintenance intervals ........................................... 39
Tools and aids ....................................................... 39
Unlocking the bench ............................................. 40
Acrylic panes......................................................... 40
Filter panes............................................................ 42
Tubes..................................................................... 44
P2 Tubes................................................................ 44
Facial tanners ........................................................ 44
Interior unit lighting................................................ 45
Filter cartridges ..................................................... 46
Ventilation and air-conditioning............................. 47
Recording to an SD card....................................... 48
Aroma- und aquaCool........................................... 49
aquaCool nozzles.................................................. 50
System messages ............................................... 51
Technical data...................................................... 53
Views ..................................................................... 53

Operating Instructions |megaSun 5600 5
About these instructions
This operating manual is intended for use by
• operating staff,
• users,
• service staff.
Any person dealing with this tanning device must
have read and understood these instructions.
This manual describes tanning devices equipped
with the maximum number of features.
Keep this manual ready to hand at all times.
Safety signs
This symbol indicates that general haz-
ards exist for the human health.
This symbol indicates that due to elec-
trical tensions hazards exist to the
human health.
This symbol indicates that due to UV
radiation hazards exist to the human
health.
This symbol indicates that due to fall-
ing loads hazards exist to the human
health.
This symbol indicates the danger of
pinching.
When closing and opening panels and
covers, you can pinch your hands.
This symbol indicates the danger of
burns from hot lamps and housing parts.
If the tanning device was operated
before being switched off and opened,
lamps and housing parts may be hot.
This symbol indicates that damages
may occur at the tanning device, at the
material or at the environment.
IMPORTANT INFORMATION
This symbol does not identify safety
notices, but states information for a bet-
ter understanding.
Signal words
DANGER
• Death or serious injury is imminent.
WARNING
• Death or serious injury is possible.
CAUTION
• Moderate or minor injury is possible.
General information

Operating Instructions |megaSun 5600
6
Transport by forklift truck
WARNING
Overturning load
Danger of being crushed by heavy parts
of the equipment.
• Keep the safety distance to the trans-
port machine.
• Do not walk under the load.
• Wear safety shoes.
The tanning device may be damaged
when using short forks.
• Use only sufficiently long forks.
The tanning device is mounted on a pallet.
• Insert the forks carefully into the openings of the
pallet.
• Lift the load by a few centimeters.
• Transport the load carefully to the place of
installation.
Other modes of transport
If a forklift truck cannot be used for transport, the tan-
ning device must be partially disassembled and the
parts must be transported individually to the place
of installation, e.g. using a dolly. Depending on the
weight of the components, lifting them might require
several people..
Old equipment disposal
This tanning device consists of
components that cannot be thrown into the
household garbage!
Dispose of your old equipment in an environmentally
friendly manner after the end of its useful life. Metals
and plastics can be recycled. Electrical and elec-
tronic components must be disposed of as e-waste.
Fluorescent lamps must be dropped off at authorized
collection points for pollutants.
This helps to avoid damaging effects to the
environment and human health caused by improper
disposal.
This makes a valuable contribution to recycling and
other forms of utilization of old electrical and elec-
tronic equipment.
You can obtain information about environmentally
friendly disposal from your local government or the
municipal administrations.
CAUTION
Risk of mercury toxicity
Risk of mercury toxicity after a lamp
breakage.
• Ventilate the room / environment at least
15 minutes before disposing the lamp
fragments.
Service
For all service-related questions, please contact your
responsible specialist dealer.
Updating system software
Risk of damage by switching off the
power supply voltage.
Disconnecting power supply during the
update process, will lead to damage of elec-
tronic components.
• Make sure that the tanning device is not dis-
connected from the power supply voltage dur-
ing the update.
To accomplish the update download the “USB-
Connect” software offered by KBL. For detailed
information press the help-button in the main menu.

Operating Instructions |megaSun 5600 7
This chapter provides a summary of general infor-
mation on safety and proper handling of the device.
More specific safety advice is given in other chapters
of the operating manual.
Intended use
This tanning device is intended to be used for the
tanning of one single person at a time. This person
must not fall in one of the categories mentioned
below, otherwise using the tanning equipment is
prohibited for him or her.
The following individuals must not use the tanning
device:
• Persons under 18 years of age.
• Persons with heart pacemakers.
• Persons, who are suffering or have suffered from
skin cancer or have a predisposition toward this,
or those whose first-degree relatives are suffering
or have suffered from malignant melanoma (black
skin cancer).
• Persons taking photosensitive medications.
• Persons, who are being treated by a physician for
conditions associated with photosensitivity.
• Persons suffering from acute sunburn.
• Persons, who are prone to freckles.
• Persons with atypical discoloured skin areas or/
and with more than five atypical moles with a
diameter of 5 millimetres or more and persons with
more than 16 moles with a diameter greater than or
equal to 2 millimetres. If in doubt, consult a physi-
cian!
• Persons, who had several severe sunburns as chil-
dren.
• Persons with naturally red hair colour.
• Persons, who do not tan at all or cannot tan with-
out getting sunburn.
• Persons, who have a predisposition toward sun-
burn.
Lie down on the bench in a straight position and with
physical contact to the bench. Choose a suitable
position to reach the interior control panel at all times
during the tanning.
Foreseeable misuse
• This tanning device is not designed to be used by
persons with reduced physical, sensory or mental
abilities and lack of experience and/or insufficient
knowledge.
• During operation, no other person may remain in
the radiation area of the tanning device.
• Children should be supervised to ensure that they
do not play with the tanning device.
• The irradiation of animals, especially reptiles.
• Any type of use that differs from the provisions
under the chapter Intended use is considered mis-
use.
Safety notes

Operating Instructions |megaSun 5600
8
Duties of the operator
The manufacturer cannot be held liable for dam-
ages or injuries resulting from improper use of the
equipment or non-observance of these operating
instructions.
Only use spare parts approved by KBL, otherwise
operating authorization and terms of guarantee
will become invalid. Only replace tubes and high
pressure lamps with those listed on the device.
Otherwise, this voids the operating authorization and
warranty!
General safety advice
• Follow all instructions given in this manual. In addi-
tion, observe all relevant statutory provisions and
regulations, also those applicable in the country of
operation.
• The tanning device may only be installed and set
up by trained and authorised personnel having
received safety-related instruction.
• Arbitrary modifications or conversions of the equip-
ment are not permissible.
• Observe all danger signs and safety notices
attached to the equipment.
• Safety notices must not be removed, and safety
equipment must not be disabled or removed.
• The tanning device must only be operated when in
perfect working condition.
• Never operate the tanning device with the outer
covers or acrylic panes removed.
• Absolutely observe the maintenance frequencies
indicated in the maintenance plan.
• Pay attention to the load limit of the bench pane
(tanning bed units only).
The canopy is not designed to carry
additional loads.
• Do not lean over the equipment cover.
Timer operation
The tanning device must be controlled via an external
timer that meets the requirements of EN 60335-2-27,
cl. 22.105. Should the external timer fail, an internal
timer will switch off the tanning device automatically
after 33 minutes.
Tanning times
Adhering to tanning times and schedules is essential.

Operating Instructions |megaSun 5600 9
Standards
This tanning device complies with the following
standards in their respectively applicable version:
• EN 60335-2-27
• EMC 2014/30/EU
• Low Voltage Directive 2014/35/EU
Components
The tanning device basically consists of the following
components:
• The canopy including 26 tubes, 4 facial tanners
and interior control panel.
• The bench part including 16 tubes and the elec-
tronic unit. Depending on the model also with
optionally available components.
1Canopy
2Locking bar with the locks for the canopy
pane.
3Interior control panel
4Facial tanner
5Audio console with sound system. (optional
equipment)
6Bench (faceplate)
7Opening mechanism of the bench part
8Bench pane
9aquaCool - nozzles (optional equipment)
10 Canopy pane
11 Air nozzles
12 Decorative lighting
megaSun 5600
Description of the unit
③
④
②
⑤
①
⑥
⑨
⑦
⑧
⑩
⑪
⑫

Operating Instructions |megaSun 5600
10
For information on further tanning
device connections, refer to your
ASSEMBLY INSTRUCTION in the sec-
tion “Connections & Initial operation”.
Level adjustment studio music
signal
The voice / audio system components are built in the
middle of the bench part (vacuum housing) of the
tanning device. The potentiometer which serves of
the external audio signal is located on the left side
of the housing. To avoid overdrive, select the level
adjustment accordingly. The level setting depends
on the strength of the external signal and should be
carried out by a service engineer. Adjustment of the
sound level can only be conducted in the service
menu.
Operation using different
audio sources
The tanning device can be operated using the
following audio sources:
• An internal audio source
• Various external audio sources
• All available audio sources
The audio source can be changed via the interior
control panel.
INTERNAL MP3 PLAYER
When using the internal MP3 player, you can either
play the music tracks that are originally supplied on
the SD card, or you can record your own tracks to
the SD card.
EXTERNAL AUDIO SOURCES
LINE-IN
As an external audio source, you can connect
devices ranging from the standard-line level to low
loudspeaker levels.
These sources comprise:
• Studio music
• External players such as MP3 players, mobile
phones (cell phones), I-pods, etc.
EXTERNAL 100 V AUDIO SIGNAL ON STUDIO
CHANNEL (OPTIONAL FEATURE)
If you decide for a connection to a 100 V audio
system, you will need a transformer (KBL no.: 9100
0170 00) for the transmission of the audio signal.
This connection must be made by trained and
authorised personnel.
Connections - Audio

Operating Instructions |megaSun 5600 11
EXTERNAL PLAYERS & HEAD-/EARPHONES
A line connection has been integrated into the audio
module so that the tanning device user can con-
nect his or her own player such as an MP3 player,
an iPod, etc. Take hold of the jack plug and pull the
cable out of the opening. Then connect the jack
plug to the earphone jack of your player. Then select
”MP3 ext.” as the audio source from the control
panel of the tanning device before you start play-
ing your own tracks from the player. For players with
bluetooth playback starts automatically.
The tracks can only be selected via the user’s own
player. The volume can be controlled via the control
panel of the tanning device and also via the corre-
sponding operating elements provided by the user’s
player.
Either a headphone or an earphone with a 6.3 mm
jack plug can be used. The corresponding connec-
tor socket is located next to the line connector. The
audio signal is switched over automatically.
MP3
ATTENTION
• Danger of damage to the player due to
overheating.
• Do not place your player within areas that are
directly exposed to UV radiation.
• Use the small ledge at the audio module.
Bluetooth connection
To connect an external player (smartphone etc.) wire-
lessly to the tanning device an optional Bluetooth
interface is available.
CONNECT EXTERNAL PLAYER
A Bluetooth connection can be established in
standby and during tanning mode.
Make sure that you are within the recep-
tion area (about 2 meters).
Make sure that your player is configured
to search for other bluetooth devices.
Should this not be the case, enable blue-
tooth manually. To do so, please read the
instructions for your player.
• Depending on your settings the search will be
performed automatically or manually. All available
bluetooth devices within reach will be listed after
a short time.
• Among the available tanning devices choose
“megaSun”. In the service menu, a trailing number
(01, 02, 03, ...) can be added to tanning device
name.
• If necessary confirm the shown code and connect
again. Not every smart phone asks for a code.
megaSun 01
megaSun 01

Operating Instructions |megaSun 5600
12
• A two-time beep indicates that your player is con-
nected to the tanning device.
megaSun 01
megaSun 01
• Set your player to a medium volume level and
start the music.
• Adjust the volume level on your player.
• During the tanning session, the volume control has
to be done at the tanning device.
DISCONNECT EXTERNAL PLAYER
An existing connection is disconnected automati-
cally after tanning.
The connection is automatically disconnected if the
tanning session is not started within 6 minutes.
COMPATIBILITY OF BLUETOOTH DEVICES
KBL AG attaches great importance to hardware com-
patibility. Due to the large number of manufacturers,
KBL can not guarantee a 100 % compatibility. In rare
cases, it may happen that a bluetooth connection
can not be established.
CORRECTIVE ACTION
Each bluetooth device offers a list of paired devices.
Delete the older entries in this list which have a pro-
file that overlaps with the ones for which you want to
pair your player.
Start the bluetooth device detection again.

Operating Instructions |megaSun 5600 13
Start-up
Before switching on for the first time:
• Fix the supplied warning sign or one with the
following wording permanently to the wall close to
the tanning device:
Warning
• UV-radiation can cause eye and skin damage as
well as skin aging and possibly skin cancer. Ask
the studio staff for further information.
• Wear protective goggles.
• Certain medicines or cosmetics can increase the
sensitivity of the skin to UV radiation. If in doubt,
consult a physician.
• Determine the presettings for the tanning device in
the service menu.
• Check correct installation of fluorescent tubes.
The tube labeling must be visible, otherwise no
tanning effect may be obtained.
• Store these Operating Instructions in a place that
allows for easy access at any time.
Operating modes
The three different operating modes and the fan
run-on mode are explained below:
STANDBY MODE
The tanning device is in an idle state, i.e. it is
connected to the mains but is currently not being
used. The tubes and the tanning lamps are switched
off. From the standby mode, you can change over to
the tanning mode or to the service mode.
TANNING MODE
The tubes and the tanning lamps are switched
on and a tanning session is in progress. While the
tanning device is in tanning mode, the settings for
the ongoing tanning session can be changed via the
interior control panel.
SERVICE MODE
In the service mode, the tanning device is configured
for the tanning mode. Various values can be displayed
and test functions can be carried out.
FAN RUN-ON
After the tanning session, the fan runs on for 3
minutes in order to cool down the tanning device.
The fan power is automatically decreased as the
tubes cool down.

Operating Instructions |megaSun 5600
14
Tanning instructions
As a rule, an averagely tanning skin has achieved
a uniform tan after three to five tanning sessions.
These sessions should take place every second day.
To preserve the suntan achieved, one or two tanning
sessions per week are normally sufficient.
Instructions for the user
Observe the following tanning instructions:
NO SUNSCREEN WITH PROTECTION FACTOR
Sunscreens with sun protection factors are unsuitable
for use in a tanning salon. For tanning, the skin
should have been thoroughly cleaned and be dry. For
optimum skin care, we recommend using our body-
care products after tanning.
GENERAL
• Any person that complies with the requirements
laid down in the chapter “Intended use” may use
the tanning device.
• Never exceed your personal minimum erythema
dose (MED). Follow the prescribed exposure times.
• If reddening of the skin (erythema) occurs hours
after tanning, temporarily stop tanning. After a
week the tanning can be resumed at the beginning
of the tanning table.
• If unexpected effects (such as itching) occur within
48 hours after the first tanning session, you should
consult a physician before tanning again.
• Once final tanning has been achieved, additional
tanning is only possible by greatly exceeding the
permissible tanning times. It is essential to avoid
this.
• UV-radiation from the sun or from UV-devices can
cause irreversible skin or eye damage. These bio-
logical effects depend on the type and amount of
radiation as well as on the individual sensitivity of
the skin.
• In cases of pronounced individual sensitivity or allergic
reactions to UV-radiation, a physician should be con-
sulted before beginning tanning.
• After excessive exposure to radiation, the skin may
exhibit sunburn. Excessively repeated exposure to
UV radiation of sunlight or UV appliances can result
in premature ageing of the skin and in a higher risk
of skin cancer.
• The unprotected eye can suffer from surface
inflammation, and in certain cases, e.g. after a cat-
aract operation, excessive radiation can damage
the retina. After many repeated sessions, a cata-
ract may form.
• Seek medical advice if persistent swellings or sores
develop on the skin or if pigmented moles change
in appearance.
FOR EACH TANNING SESSION
• Always wear the supplied protective goggles. Con-
tact lenses or sunglasses are no substitute for the
protective goggles!
• Remove cosmetics before tanning and do not use
any sunscreen, or products that accelerate tan-
ning.
• Allow for at least 48 hours to pass between
sessions.
• After a tanning session in a studio, do not take
another sunbath out of doors on the same day
• Protect sensitive areas, such as scars, tattoos, and
genitalia, from radiation.

Operating Instructions |megaSun 5600 15
Tanning times
Please refer to the following tables for learning the individually applicable tanning times that depend on the skin
type. If the tanning session sequence is interrupted for 4 weeks or more, you will have to start with the first ses-
sion again.
The interval between two tanning sessions must be at least 48 hours.
The times mentioned in the tanning schedules only apply on the condition that tubes are replaced according to
the maintenance intervals stipulated in the section dealing with maintenance.
EU TANNING SCHEDULE - according to UV-Type III and 0,3W/m2in compliance with EN 60335-2-27
Skin type
I II III IV V VI
1. Session 6 min 6 min 6 min 6 min 6 min 6 min
2. Session 6 min 7 min 7 min 8 min 10 min 11 min
3. Session 7 min 7 min 9 min 10 min 14 min 17 min
4. Session 7 min 8 min 10 min 12 min 19 min 22 min
5. Session 8 min 9 min 12 min 14 min 23 min 28 min
6. Session 9 min 10 min 13 min 16 min 27 min 33 min
7. Session 9 min 11 min 15 min 19 min 32 min 33 min
8. Session 10 min 12 min 16 min 21 min 33 min 33 min
9. Session 10 min 13 min 18 min 23 min 33 min 33 min
10. Session 11 min 14 min 19 min 25 min 33 min 33 min
Max. number of tanning sessions per year
5600 devices 71 56 41 31 24 24

Operating Instructions |megaSun 5600
16
Tanning mode
START BUTTON
• Starts the tanning session during the timer con-
trolled lead time,
• as well as after an interruption caused by pressing
the STOP button, provided that the booked tan-
ning time has not elapsed yet.
STOP BUTTON
• Stops the tanning session
if pressed for at least two
seconds.
DISPLAY
• Shows the menu items and
functions.
• Indicates the tanning time.
• Information line.
ARROW BUTTONS
• Allows the selection of
subordinate functions.
+/-BUTTONS
• Control the functions.
Position recessed
button
WARNING
Excessive dose of UV radiation
Excessively prolonged tanning sessions
may cause severe damage to skin and
eyes.
• Never operate the tanning device with a
defective timer.
• Observe the tanning times given in the
tanning schedule.
The following explanations and functions refer to a
tanning system that is fully equipped with all features.
Starting the tanning session
The tanning session automatically starts after the
timer controlled lead time has expired. During the
preset lead time the tanning session can be started
anytime manually using the START button.
Operation during the tanning
session
You can control the functions of the tanning device via
the interior control panel during the tanning session.
It is particularly easy for you to access the basic
functions. Buttons with recesses that can easily be
sensed allow for easy operation of the system even
with your eyes closed.
NOTES:
20 seconds after your last input, the interior control
panel changes over to the indication of the tanning
time. An information line at the bottom edge of the
interior control panel shows the current music track.

Operating Instructions |megaSun 5600 17
During the tanning session, you need quick access to basic functions
such as volume control, body fan and facial tanners.
You should also be in a position to change the subordinate functions.
The interior control panel caters for both requirements. You have
• direct access to frequently needed functions via the “Basic functions”
section, and
• access to the subordinate functions you made via the variable section
of the interior control panel (display according to the rotation principle).
During the tanning session, you continue to have access to
subordinate functions. If you wish to make any changes,
you can do so in the variable section of the interior control
panel. By pressing one of the arrow buttons ,
above or below the changeover symbol , all available
functions will be displayed one after the other according
to the rotation principle. You can switch these individual
functions on or off and, if possible, make changes to the
settings.
Selectable function symbols (for a fully equipped tanning device)
MP3-int. Studio MP3-ext. aquaCool Aroma megaVoice Air-con.
The basic functions portrayed here
refer to a fully equipped tanning bed.
If you have chosen a simpler equip-
ment package, functions from the
variable operating elements auto-
matically take the place of the miss-
ing basic function.
Variable section
of the interior control panel
Basic functions
Prerequisite:
The functions must be
available and activated in the
service menu.

Operating Instructions |megaSun 5600
18
Aroma megaVoice
aquaCool
An ongoing spraying process cannot be
stopped. If the aquaCool supply is running
low, a corresponding message is displayed
in the standby mode. After the message has
appeared for the first time, the aquaCool
supply will last for approximately another 2.5
hours of operation. If the system has run out
of aquaCool liquid, the aquaCool function is
deactivated automatically, and the symbol
shown below is displayed.
aquaCool is automatically re-activated as
soon as a full canister has been connected.
on
off
Air-conditioning
After the air-conditioning system
has been switched off, it cannot be
restarted for three minutes for safety
reasons. If the system is switched on
during this time, the command will be
stored. The air-conditioning system
will be switched on automatically after
a delay, i.e. after the blocking time has
elapsed. If the condensate canister is
full, the following symbol flashes on
the interior control panel:
See also the chapter “Maintenance/
Air-conditioning system”.
Basic functions
Body fan
The body fan is automati-
cally controlled by ACS. As
soon as you press one of
the fan buttons, the auto-
matic mode is interrupted.
Keep pressed
for 2 seconds
max/on
min/off
Facial tanner
Keep pressed
for 2 seconds
Remark on facial tanner operation:
For safety reasons, the facial
tanner, once switched off, cannot
be switched on again before three
minutes have elapsed.
If you try to activate the facial tanner
during this time, your command
will be stored, and the tanner will
be switched on automatically after
a delay, i.e. after the blocking time
has elapsed.
II
I
Volume
Variable section of the interior control panel

Operating Instructions |megaSun 5600 19
Variable section of the interior control panel (audio functions)
Studio
MP3 internal
This function is used to play the tracks of the internal
MP3 player of the tanning device.
If the MP3 internal function has been activated, press
the plus and minus buttons to browse through the
individual tracks.
This function is used to play the studio music.
If the Studio function has been activated, you can
press the plus and minus buttons to browse through
the channels, provided that more than one channel
is available.
MP3 external (AUX)
The audio module of the tanning device is equipped
with a cable with a 3.5 mm jack plug so that you
can make use of external players, such as MP3
players, iPods, etc. In this way, you can connect the
headphone jack of your player to the tanning device.
Use the corresponding operating elements of the
external player in order to select the desired tracks.
With the “MP3 external” control element you have
also access to a Bluetooth connected device.
Channel
Channel
MODEL: ACTIVATING AUDIO FUNCTIONS
S
E
L
E
C
T
ACTIVATE
AUDIO FUNCTIONS
There is a maximum of three audio sources
available at the user’s disposal. If you
change over to another source, you must
activate it first. The activation is effected by
pressing the or the button.
All inactive audio functions are marked with
“OFF” on the interior control panel so that
you can easily recognise the active audio
source.
Tracks
Tracks

Operating Instructions |megaSun 5600
20
Standby mode / service mode
While the tanning device is in standby mode, you can
switch the decorative lighting of the tanning device
on and off and trigger an aquaCool spraying test (1
spraying cycle).
When the tanning device is in service mode, you can
make the presettings for operation in tanning mode,
and you can have values concerning the operation of
the tanning device displayed.
Layout of the interior control
panel numbers
The buttons of the interior control panel are allocated
double functions. In addition to the standard
operating elements, they stand for numbers that,
in standby mode, provide access to standby and
service functions. Simply enter the corresponding
sequence of numbers on the interior control panel.
123 4 5
0
98
7
6
Switching the decorative
lighting on and off
505
NOTE
The connection times of the decorative lighting can
be set in the service menu individually for each day
of the week.
There are two independent connection periods (A
and B) available for each day of the week.
aquaCool spraying test
494
Invoking the service menu
CALL SERVICE MENU - START WINDOW
1 6 1
SERVICE MENU - START WINDOW
SERVICEMENU
Enter Servicemenu CODE
> CODE:
In standby mode, the service level is accessed by
entering the factory CODE 1 „00000“, the supplied
CODE 2 or individually defined CODES.
• No incoming signal from the coin-box system.
NOTE
Do not let too much time pass between the individual
keystrokes when entering a sequence of numbers!