KBL megaSun 5800 User manual

Operating Instructions

Version: BA_5800_US (0708)
Item no.: 0100036503
Copyright and Trademark
© Copyright 2007 KBL AG
This documentation only covers products manufactured by KBL AG. It must not be duplicated, photocopied, trans-
lated or stored without prior special consent by KBL AG. Duplication on electronic media or in a machine-readable
form, either in whole or in part, is also prohibited.
Certified according to EN ISO 14001:2004 / DIN EN ISO 14001:2005
KBL AG
Ringstraße 24-26 · 56307 Dernbach · Germany
fon +49(0)2689.9426-0 · fax [phone]

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 3
Contents
About these instructions ......................................... 4
Safety notes ............................................................ 5
General safety advice.............................................. 5
Intended use............................................................ 7
Timer controlled operation ...................................... 7
Transportation ......................................................... 8
Transportation by forklift truck ................................ 8
Other modes of transportation................................ 8
Description of the unit ............................................. 9
Standards ................................................................ 9
Components............................................................ 9
Connections .......................................................... 10
Connecting the mains voltage............................... 10
Connecting an external audio source ................... 11
Level adjustment ................................................... 11
Operation using different audio sources ............... 11
Connecting the external timer ............................... 13
Connecting the channel selection ......................... 13
aquaCool and Aroma connections........................ 14
Start-up ................................................................. 15
Operating modes................................................... 15
Tanning instructions .............................................. 16
Instructions for the user ........................................ 16
Exposure schedule................................................ 17
Operation in tanning mode.................................... 18
Assuming the tanning position and starting / stop-
ping the tanning session ....................................... 19
Functions (KBL/4).................................................. 19
Functions (KBL/5).................................................. 22
Information for the studio operator ....................... 24
Standby/service mode .......................................... 25
Turning the decorative lighting on and off............. 25
Service menu......................................................... 25
Overview: KBL5 service menu .............................. 26
Overview: KBL4 service menu .............................. 27
Information about operation .................................. 31
Displaying the operating hours of the solarium ....... 31
Displaying the operating hours of the tubes ........... 31
Resetting the operating hours of the tubes .......... 31
Setting the timer function of the deco lighting ..... 31
Setting date and time ........................................... 32
Entering PIN II ......................................................... 32
Setting aquaCool characteristics ......................... 32
Setting Aroma characteristics .............................. 33
Setting the audio music system ........................... 34
Functions C‘M‘A‘B‘ .................................................. 36
Air-conditioning functions .................................... 36
Setting the operating hours of the tubes .............. 36
Download information ........................................... 37
Settings aquaCool (on/off) .................................... 37
Aroma/Aqua test .................................................. 37
Querying software info ......................................... 37
Setting the easyCare unit ..................................... 37
Entering PIN III ......................................................... 38
Maintenance and cleaning .................................... 39
Instructions for cleaning and care......................... 39
Maintenance intervals ........................................... 40
Acrylic panes......................................................... 40
Filter panes............................................................ 42
Tubes, facial and shoulder tanners........................ 43
Replacing the sunlamps of the shoulder tanner.... 43
Dismantling the tanning lamps.............................. 45
Decorative lighting (fourSeasons).......................... 46
Filter pads.............................................................. 46
Canopy drive ......................................................... 47
Cooling and exhaust air ........................................ 48
Air-conditioning unit .............................................. 49
Condensate pump................................................. 49
Audio system with mp3 sound box....................... 50
Recording to an SD card....................................... 51
Refilling Aroma and aquaCool............................... 51
Error messages ..................................................... 53
Service................................................................... 54
Technical data ....................................................... 55
Views ..................................................................... 56
KBL STANDARD WARRANTY ............................... 57

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
4
About these instructions
This operating manual is intended for use by
• operating staff,
• users,
• service staff.
Any person dealing with this tanning unit must have
read and understood these instructions.
This manual describes units equipped with the
maximum number of features.
Keep this manual ready to hand at all times.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 5
Safety notes
This chapter provides a summary of general
information on safety and proper handling of the
device. More specific safety advice is given in other
chapters of the operating manual.
General safety advice
WARNING - ULTRAVIOLET RADIATION - FOLLOW INSTRUCTIONS - FAILURE TO USE PROTECTIVE
EYEWEAR MAY RESULT IN SEVERE BURNS OR OTHER EYE INJURY - IF DISCOMFORT DEVELOPS,
DISCONTINUE USE AND CONSULT A PYSICIAN.
ATTENTION - RAYONNEMENTS ULTRAVIOLETS - VEUILLEZ SUIVRE LES INTRUCTIONS - SANS DISPOSITIF
DE PROTECTION DES YEUX, CE PRODUIT PEUT CAUSER DES BRÛLURES OU LÉSIONS OCULAIRES GRAVES
- SI VOUS SENTEZ UN MALAISE, EN DISCONTINUER L'USAGE ET CONSULTER UN MÉDECIN.
Part No. 3010370800
DANGER - Avoid overexposure. As with natural sunlight, overexposure can cause eye and skin injury and allergic reaction. Repeated
exposure may cause premature aging of the skin and cancer.
Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using sunbed if you are using
medications or have a history of skin problems or believe yourself especially sensitive to sun light. If you do not tan in the sun you are
unlikely to tan from use of this product. Children, the elderly, or fair skinned people who always burn easily and either never tan or tan
minimally should not use this equipment.
DANGER - Eviter surexposition. Comme avec la lumière naturelle du soleil, la surexposition peut causer lésions aux yeux et à la peau
et réactions allergiques. Une exposition répétée peut causer un vieillissement prématuré de la peau et cancer.
Médicaments et cosmétique peuvent augmenter votre sensibilité aux rayons ultraviolets. Consulter un médecin avant d'utiliser la lampe à
ultraviolets si vous utilisez médicaments, si vous avez problèmes de peau ou si vous croyez vous êtes particulièrement sensibles au rayons
du soleil. Si vous ne bronzez pas avec le soleil c'est improbable que vou povez vous bronzer en utilisant ce produit. Enfants, personnes
agées, ou personnes á peaux très claire, qui deplus sont très sensibles à un coup de soleil et ne brunisent pas ou très peux ne doivent
pas utiliser cet appareil de bronzage.
This device may be used only by persons
over 18 years (local law may differ) and is
intended to be used by only one person at
a time. Lie down on the bench in a straight
position and with physical contact to the
bench.
CAUTION:EXPOSURE POSITIONS
O T H E R T H A N S P E C I F I E D M A Y
RESULT IN OVEREXPOSURE AND
ARE NOT RECOMMENDED.
Tanning normally begins after one to two
exposures and maximizes after one to four
(1-4) weeks of exposure following the
recommended schedule for your skin type.
Wear protective eyewear.
Eyewear: AHK GmbH, No. 600545
This product is in conformity with
performance standards for sunlamp
products under No. 21 CFR 1040.20.
This appliance is intended to be used with
the following lamps:
Canopy: megaLine 1862 R 160W
Ben ch: m ega Lin e 186 2 R 160 W
Fac ial un its : m ega Line H P 500
Shoulder tanner (optional): ms 250
For replacement lamps, eyewear or parts
please contact:
KBL America Inc.
1324 Washington Avenue
ST. Louis, MO 63103, USA
DO NOT REMOVE THIS LABEL
Read the instruction booklet before using tanning system
RECOMMENDED EXPOSURE SCHEDULE
First three sessions should be at 48 hour intervals.
Followed by the gradual increasing of exposure
times until maximum tanning has occurred
(in approximately 4 weeks).
MAXIMUM EXPOSURE is 12 minutes.
Skin
type
Week 1
1st - 3rd
Session
Week 2
4th - 6th
Session
Week 3
7th - 9th
Session
Subsequent
Weekly
Session
II
III
IV
V
2 min
2 min
2 min
2 min
5 min
5 min
5 min
6 min
7 min
7 min
8 min
9 min
9 min
10 min
11 min
12 min Part No. 3010371504 A
This device may be used only by persons
over 18 years (local law may differ) and is
intended to be used by only one person at
a time. Lie down on the bench in a straight
position and with physical contact to the
bench.
CAUTION:EXPOSURE POSITIONS
O T H E R T H A N S P E C I F I E D M A Y
RESULT IN OVEREXPOSURE AND
ARE NOT RECOMMENDED.
Tanning normally begins after one to two
exposures and maximizes after one to four
(1-4) weeks of exposure following the
recommended schedule for you skin type.
Wear protective eyewear.
Eyewear: AHK GmbH, No. 600545
This product is in conformity with
performance standards for sunlamp
products under No. 21 CFR 1040.20.
This appliance is intended to be used with
the following lamps:
Canopy: megaLine 1870 R 160W CPI plus
Bench: megaLine 1870 R 160W CPI plus
Fac ial un its : m ega Line H P 500
Shoulder tanner (optional): ms 250
For replacement lamps, eyewear or parts
please contact:
KBL America Inc.
1324 Washington Avenue
ST. Louis, MO 63103, USA
DO NOT REMOVE THIS LABEL
Read the instruction booklet before using tanning system
RECOMMENDED EXPOSURE SCHEDULE
First three sessions should be at 48 hour intervals.
Followed by the gradual increasing of exposure
times until maximum tanning has occurred
(in approximately 4 weeks).
MAXIMUM EXPOSURE is 12 minutes.
Skin
type
Week 1
1st - 3rd
Session
Week 2
4th - 6th
Session
Week 3
7th - 9th
Session
Subsequent
Weekly
Session
II
III
IV
V
2 min
2 min
2 min
2 min
5 min
5 min
5 min
6 min
7 min
7 min
8 min
9 min
9 min
10 min
11 min
12 min Part No. 3010371506 A

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
6
Read the instruction booklet before using this device.
This device must be operated with an external timer
that is specified in chapter „Timer controlled opera-
tion“.
This device may be used only by persons over 18
years and is intended to be used by only one person
at a time.
Tanning can begin on a regular basis. An appearance
of tanning normally appears after a few exposures
and maximizes after four (4) weeks of exposure.
WARNING: As the device is intended to be used by
only one person at a time, only one (1) pair of pro-
tective eyewear is provided with each KBL tanning
device. Use protective eyewear whenever equipment
is energized. Read the instruction booklet before
using.
Follow the exposure schedule (see chapter „Expos-
ure schedule“) in accordance with your skin type.
Failure to do so may result in overexposure. Howe-
ver, regardless of how dark an individual may tan on
this system, it will not provide adequate protections
against overexposure to natural sunlight or UVB tan-
ning systems.
SKIN TYPE II - This is the individual that usually
burns easily and severely, tans minimally or lightly
and peels.
SKIN TYPE III - Often referred to as „AVERAGE“ com-
plexion. Burns moderately and tans about average.
SKIN TYPE IV - This individual burns minimally, tans
easily and above average with each exposure.
SKIN TYPE V - This individual rarely burns, tans easi-
ly and substantially.
Duties of the operator
KBL cannot be held liable for any damage resulting
from improper use of the equipment or non-
observance of these operating instructions.
Only original spare parts – especially tubes and
burners – have to be used, otherwise operating
authorization and terms of guarantee will become
invalid.
FURTHER INSTRUCTIONS
• Follow all instructions given in this manual. In addi-
tion to that, observe all applicable statutory provi-
sions and regulations, also those applicable in the
country of operation.
• The appliance may only be installed and assembled
by specifically trained staff.
• Arbitrary modifications or conversions of the equip-
ment are non-permissible.
• Observe all danger signals and safety signs atta-
ched to the equipment.
• Safety signs must not be removed, and safety ap-
pliances must not be disabled.
• The unit may only be operated when in perfect
working condition.
• Never operate the device with the outer covering
removed or with the acrylic panes removed.
• The tanning system has to be controlled via a timer
that complies with the generally applicable stan-
dards.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 7
Intended use
The unit is intended to be used for the tanning of
one single person at a time. This person must not fall
in one of the categories mentioned below, otherwise
using the tanning equipment is prohibited for him or
her.
The following individuals must not use the device:
• Persons under 18 years of age
• Persons wearing heart pacemakers
• Person prone to sunburn, without the desired tanning
effects, when exposed to the sun (skin type I)
• Persons already suffering from sunburn
• Persons suffering, or having suffered, from skin cancer,
or persons with a corresponding predisposition
• Persons taking medicines
Furthermore, this tanning unit has been designed for
use by individuals who are in full command of their
physical, sensorial and mental faculties. Moreover,
sufficient knowledge and experience are required.
Children should be supervised to make sure that they
do not use the unit as a toy.
Timer controlled operation
This device must be operated with an external timer
that is listed in compliance with UL 917.
If the external timer fails, the device is automatically
switched of, by an internal safety timer, after the re-
spective Te-Time of the different units.
The maximum tanning time must not be exceeded.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
8
Transportation
Transportation by forklift
truck
The device is mounted on a pallet.
• Insert the forks carefully into the openings of the
pallet.
• Lift the load by a few centimeters.
• Transportation the load carefully to the place of
installation.
Other modes of transportation
If a forklift truck cannot be used for transportation,
the box must be unpacked and the parts inside must
be transported individually to the place of installation,
e.g. using a dolly. Depending on the weight of the
components, lifting them might require several
people.
WARNING!
Overturning load!
Danger of being crushed by heavy parts
of the equipment.
• Wear safety shoes.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 9
Standards
This product is in conformity with performance
standards for sunlamp products under
No. 21 CFR 1040.20.
Components
The tanning unit basicallly consists of the following
components:
• The canopy including 20 tubes, ambient air supply
and facial tanners.
• The side part including 6 tubes
• The base part including 18 tubes, the electronics
unit and further, optionally available components
KBL 5800, canopy opened
Figure 9.1
①③④Front view, canopy opened
Figure 9.2
①②③⑥
Top view, canopy opened
Figure 9.3
①⑤1Canopy
2Canopy pane
3Base section
4Bed pane
5Air supply connector in the canopy
6Side pane
Description of the unit

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
10
Connections
Connecting the mains voltage
DANGER!
Live components
Risk of fatal injury due to electric shock
when touching live parts.
- Switch off mains voltage.
- Protect against re-connection.
Both the power supply and the related connection
work must comply with national standards. The
connection work must only be performed by qualified
expert staff. The connection to the 3 x 220 V mains
must be protected by fuses. Their specifications are
listed in the chapter “Technical data”.
A Class-A ground fault circuit interrupter (GFCI) has
to be used for Canada.
Should the operation of the tanning unit cause any
interference in the power supply network, e.g. with
ripple-control systems (TRA), consult your power
supply company to have corresponding blocking
elements (audio frequency suppressors) installed.
Figure 10.1
The tanning device is by default set up to operate
on 3 phases but it can be changed over to 2-phase
operation. The wiring for 3-phase operation is shown
below:
Figure 10.2
X5.8
X0 .N3
F2.A
K2.5
K1.5
K2.3
K1.3
K2.1
K1.1
F1.A
L2(S)
L3(T)
L1(R)
D
AB C
X2.9
gnd
X4.3
X2.1X4.1
X4.2
X7.3
X1.9
CA X5.6
X2.4
X2.2
X2.3
X0.L3
E2.3
X2.5
bas e
X0.N1
X0 .N2
K6.A 2
F1.D X1.8 X8.1
K1.5
K2.5
L2L3
PE
PE
L1L2L3
N2N3N4N5N6N7
1
L1
N1
Mains 3 x 220V / 60Hz
The wiring for 2-phase operation is shown below.
1. Re-wire the 3 cables according to the diagram.
2. Make sure that you use the right cable for the
power supply.
Figure 10.3
jumper settings
change connections
set jump er
X0.L3
X2.3
X2.2
X2.4
X5.6
CA
X1.9
X7.3
X4.2
X4.1 X2.1
X4.3
X5.8
X2.5
E2.3
bas e
K1.5
K2.5
F2.A
K1.3
K2.3
X0 .N2
X0.N1
X0 .N3
K1.1
K2.1F1.A
L1(R)
D
AB C
X2.9
gnd
K6.A 2
F1.D X1.8
X8.1
L2(S)
(K1 .5) - from[X0.L3D]to[X0.L 2C]
(K2 .5) - from[X0 .L3D]to[X0.L2C]
(X0.N1) - from[X0.L1C]to[X0.L3D]
K2.5
K1.5
from [X0.L1]to[X0.L2]
Wago item nr. 2016 - 402
KBL i tem nr. 32 00453520
(X 0.N2) - from[X0.L2C]to[X0.L3D]
N4 N3 N1N7 N6 N5 N2
L3 L2
PE
PE
L1L1L2L3
1
change connections
1(K2.5) > from [X0.L3D] to [X0.L2C]
2(X0.N1) > from [X0.L1C] to [X0.L3D]
3(K1.5) > from [X0.L3D] to [X0.L2C]
4(X0.N2) > from [X0.L2C] to [X0.L3D]
set jumper
5from [X0.L1] to [X0.L2]
----------------------------------
Wago item Nr.: 2016-402
KBL item Nr.: 3200453520
Mains 2 x 220V / 60Hz

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 11
Connecting an external audio
source
When connecting an external audio source, pay
attention to the correct polarity.
Figure 11.1
R-
green
Wiring on the audio equipment’s side
yellow white brown
R+ L- L+
Level adjustment
The voice/audio system components are built
into the base part (in the head area) of the tanning
unit. The total level adjustment is carried out via a
potentiometer (see arrow) that is located on the audio
switch circuit board.
Figure 11.2
Operation using different
audio sources
The tanning unit can be operated using the following
audio sources:
• An internal MP3 player alone
• An external audio source alone
• Both audio sources
Use the control panel to alternate between internal
and external audio source.
INTERNAL MP3 PLAYER
When using the internal MP3 player, you can either
play the music tracks that are originally supplied on
the SD card, or you can record your own tracks on
the SD card.
EXTERNAL AUDIO SOURCES
As an external audio source, you can connect
devices ranging from the standard-line level to low
loudspeaker levels.
These sources comprise:
• the studio music, and
• external players such as MP3 players, mobile
phones (cell phones), iPods, etc.
EXTERNAL AUDIO SIGNAL 100 V
(OPTIONAL FEATURE)
A transformer (KBL item no.: 9100 0170 00) is
required for the transmission of the audio signal if a
100 V audio system is connected.
The connection must be carried out by trained service
staff.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
12
Studio music
The level of the studio music can be adjusted by
means of a potentiometer on the line box. The box is
located below the bed, on the right-hand front side
(figure 9.1)
It is only fixed by Velcro tape and can be removed.
Figure 9.1
The potentiometer is located on the rear side of the
box (figure 9.2) . This is where you can adjust the studio
music to the level of the integrated MP3 player.
Figure 9.2
External players
A line-in connector is available in the head area of
the bed, on the right-hand side, so that the studio
client can plug in his/her own equipment, e. g. MP3
player, iPod, etc.
(figure 10.1) . Use a standard 3.5 mm
jack cable (included if the music option has been
ordered). If an external player is plugged into this
connector, the system switches over automatically
and plays the music of the personal player. This
assumes that you have selected the “Studio” option
of the menu item “Audio” in the service menu I.
A level adjustment is performed using the volume
control of the panel of the solarium, and the volume
control of the external player.
Figure 10.1
The tanning unit can only be operated with audio
sources if you have purchased the optionally available
audio package. For further information, please refer
to the chapter “Operation in service mode”.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 13
Connecting the external timer
CONNECTING VIA AMP PLUG (DEFAULT)
Connect the external timer (e.g. coin box, studio
control) according to the instructions supplied with
the timer. The connection is made via the socket
for an AMP plug on the back side of the device.
The following diagram shows the wiring of the timer
connection.
Figure 13.1
timer
L1
start
remote start
11
13
1
2
socket for AMP plugAMP plug
T-MAX BOX
Figure 13.2
T-MAX CONNECTOR PANEL
Figure 13.3
Connecting the channel
selection
The following diagrams show the wiring of the
channel selection on the audio equipment’s side, for
pulse coding and for BCD coding.
Figure 13.4
Wiring on the audio system of the studio
PE1 2 3 4 5
Volume +
Volume -
ch. selection -
ch. selection +
Control voltage
puls-coding
Figure 13.5
Wiring on the audio system of the studio
PE1 2 3 4 5
Control voltage
BCD-coding
Channel selection Channel selection
CHANNEL BCD CODING
1 0 0
2 1 0
3 0 1
4 1 1

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
14
aquaCool and Aroma
connections
AQUACOOL
The aquaCool box is equipped with a connection
for liquid-level monitoring ①as well as with a hose
connection each for the supply of the aquaCool liquid
②and the compressed air ③.
Figure 11.1
①②③1Connector (liquid-level monitoring)
2Inlet (aquaCool medium)
3aquaCool compressed-air supply
AROMA
The optionally available Aroma box is attached to
the rear side of the aquaCool box. The Aroma box is
equipped with three hose connections, one leading to
the Aroma tin ④and the other two to the ventilation
ducts of the foot nozzles ⑤.
Figure 11.2
④⑤⑤4Aroma box (inlet)
5Aroma box (outlets)

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 15
Start-up
Before switching on for the first time:
• Fix the supplied warning sign or one with the
following wording permanently to the wall close to
the tanning unit:
Warning!
• UV radiation can cause eye and skin injury. Ask the studio
staff for further information.
• Wear protective goggles.
• Certain medicines or cosmetics can increase the sensitivity
of the skin to UV radiation.
• Determine the presettings for the device in the
service menu.
• Store these Operating Instructions in a place that
allows for easy access at any time.
Operating modes
The three different operating modes are explained
below:
STANDBY MODE
The unit is in an idle state, i.e. it is connected to the
mains but is currently not being used. The tubes and
the tanning lamps are switched off. From the standby
mode, you can change over to the tanning mode or
to the service mode.
TANNING MODE
The tubes and the tanning lamps are switched on
and a tanning session is in progress. While the unit is
in tanning mode, the settings for the ongoing tanning
session can be changed via the control panel.
FAN RUN-ON
After the tanning session, the fan runs on for 3
minutes in order to cool down the device. The fan
power is automatically decreased as the tubes cool
down.
SERVICE MODE
In the service mode, the device is configured for the
tanning mode. Various values can be displayed and
test functions can be carried out.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
16
Tanning instructions
As a rule, an averagely tanning skin has achieved
a uniform tan after three to five tanning sessions.
These sessions should take place every second day.
To preserve the suntan achieved, one or two tanning
sessions per week are normally sufficient.
NO SUNSCREEN WITH PROTECTION FACTOR
Sunscreens with sun protection factors are unsuitable
for use in a tanning salon. For tanning, the skin
should have been thoroughly cleaned and be dry.
For optimum skin care, we recommend using our
“AfterSun” line of body-care products after tanning.
Instructions for the user
Observe the following tanning instructions:
GENERAL
• Any person that complies with the requirements
laid down in the chapter “Intended use” may use
the device.
• The different skin types tolerate the sun and hence
tanning times to a different degree. Please observe
the specifications in the skin-type table (supplied
with the unit) and the tanning times. After having
reached the ultimate tan, further tanning can only
be achieved by substantially exceeding the allowed
tanning times. This must absolutely be avoided.
• The UV radiation of the sun or of UV appliances
can cause damage to the skin or to the eyes. These
biological effects depend on the type and amount
of radiation as well as on the individual sensitivity of
the skin.
• After excessive exposure to radiation, the skin may
exhibit sunburn. Excessively repeated exposure to
UV radiation of sunlight or UV appliances can result
in premature ageing of the skin and in a higher risk
of skin cancer.
• The unprotected eye can suffer from surface
inflammation, and in certain cases, e.g. after
a cataract operation, excessive radiation can
damage the retina. After many repeated sessions,
a cataract may form.
• No exposure to UV radiation if medicine is taken
that increases the sensitivity to ultraviolet radiation.
If in doubt, seek medical advice.
• It cannot generally be assumed that the use of a
solarium reduces the risk of getting sunburn.
• Seek medical advice if persistent swellings or sores
develop on the skin or if pigmented moles change
in appearance.
• Only use radiation appliances of UV type 4 after
consulting a doctor.
FOR EACH TANNING SESSION
• Always wear the supplied protective goggles.
• Remove cosmetics before the session and do not
use any sunscreen.
• Allow for at least 48 hours to pass between
sessions.
• After a tanning session in a studio, do not take
another sunbath out of doors on the same day.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 17
Exposure schedule
For the precise definition of the skin types, please
refer to the supplied skin-type table.
If the tanning-session sequence is interrupted for 4
weeks or more, you will have to start with the first
session again.
The times mentioned in the tanning schedules
are only valid for tubes and facial tanners that are
replaced according to the maintenance intervals.
5800 ULTRA POWER - INDUCTIVE & CPI
SKIN TYPE
II III IV V
Week 1
1st - 3rd
Session
2 min 2 min 2 min 2 min
Week 2
4th - 6th
Session
5 min 5 min 5 min 6 min
Week 3
7th - 9rd
Session
7 min 7 min 8 min 9 min
Subsequent
Weekly
Session
9 min 10 min 11 min 12 min
Maximum exposure is 12 minutes!

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
18
Operation in tanning mode
DANGER!
Excessive dose of UV radiation
If the tanning session is prolonged
excessively, the skin and the eyes will be
injured severely.
• Never operate the solarium with a defective
timer.
• Comply with the tanning times given in
the tanning schedule.
The tanning mode starts automatically after the
warm-up time specified in the timer has elapsed.
During the warm-up time, the tanning session can be
started manually by pressing the START button.
Displays in tanning mode
The following section shows the display and names
its operating elements available in the tanning mode.
Which of the operating elements are actually available
on your device depends both on the optional features
selected for your tanning system and on the settings
made in the service menu.
Display
Display of session time and of change
in volume and fan power
Back to previous/forward to next
display
Volume
/
/
aquaCool: on/off/empty
/ Facial Tanner/Shoulder Tanner on/off
Body fan

O p e r a t i n g I n s t r u c t i o n s |KBL 5800 19
Assuming the tanning position
and starting / stopping the
tanning session
WARNING
UV radiation
UV radiation can cause skin and eye
injuries.
• Observe the tanning instructions.
• If in doubt, refrain from tanning.
ASSUMING THE TANNING POSITION
The door must be kept closed during the tanning
session in order to ensure the proper functioning of
the ventilation system. Persons with long hair need
to wear a hair net during the session.
1. Close the door and place yourself in the middle
of the device. Make sure that you are positioned
at an equal distance between your body and the
surrounding sunlamps.
2. Put on the protective goggles.
STARTING
To start the system during the warm-up time, press
the START button. After the set warm-up time
has elapsed, the tanning session will commence
automatically.
STOPPING
Keep the STOP button pressed for at least two
seconds. As an acknowledgment, you will hear a
sound signal, and the session-time display starts
flashing. The session is discontinued but the time
will continue to be counted. The tanning session can
be continued by pressing the START button if the
available session time has not elapsed yet.
After the time given by the timer has elapsed, the
session is terminated automatically, and the fan will
run on for three minutes.
Functions (KBL/4)
Use the plus button to switch on the
function or to set the next higher value.
Press the button as often as necessary to
set the maximum value (e.g. fan speed).
Use the minus button to switch off the
function or to set the next lower value.
Press the button as often as necessary to
set a lower value (e.g. volume).
Use the START button to switch on
the unit during the warm-up time.
If the tanning session has been interrupted by
pressing the STOP button, it can be continued by
pressing the START button, provided that the session
time available from the coin box/timer system has
not elapsed yet.
The tanning session can be terminated
prematurely by pressing the STOP
button for at least 2 seconds.
NUMERIC DISPLAY
While the tanning program is running,
the current session time is displayed
here. If you change the volume, the
set value between 0 ... 99% is
indicated here. If you change the fan speed, the value
between 20 and 99% is displayed.
TERMINATION OF THE TANNING SESSION
After the session time has elapsed, a program to shut
down the solarium is started:
A voice (for vocal guide systems) announces the
end of the tanning session and says goodbye to the
customer.
Sunlamps, tubes and ventilation are shut down in
steps.
The LEDs (for units equipped with activeColor) will
afterglow in the set color for another 20 seconds.

O p e r a t i n g I n s t r u c t i o n s |KBL 5800
20
EXTENDED MENU
The double arrows indicate that there
are further menus available that can
be invoked by touching “+” or “–”
above/below the double arrow. The
following menus are available (explained below):
Music channel / Air-conditioning / Color stimulation
Aroma function
Acoustic menu guidance
You will see which of the functions are activated after
switching on the unit (1=on; 0=off) by invoking these
further menu functions. Particular customer requests
can be preselected by making the corresponding
settings in the service menu.
VOLUME
Use the “+” and “–” buttons to control the
volume of the music. The volume is displayed
in the numeric field as a value between 0 …
99 %. Press the corresponding button as
often as necessary to reach the desired
volume. The “–” button can be used to
switch off the music: at first, set the value to 20 %,
then press the “–” button again for a longer time.
AQUACOOL
This is to switch on the aquaCool
spray mist (plus button, symbol
flashing) or to switch it off (minus but-
ton, symbol not flashing). Default set-
ting when starting the unit: as select-
ed in the menu AAC/Aqua on service
level. If the system is running short of aquaCool liq-
uid, the message “Aqua low” is displayed between
sessions. After the first message, there is sufficient
aquaCool left for approx. 2.5 hours of operation with
aquaCool.
If the system has run out of aquaCool liquid, the
message “Aqua 0%” appears and the symbol is
crossed out. If you wish to continue to operate the unit
without aquaCool, you can switch off the messages
and the symbol. To do so, go to the service level II
and set the submenu Aqua of the menu AAC to OFF.
FACIAL TANNER/SHOULDER TANNER
The control of the shoulder tanner is linked
with the facial tanner. The shoulder tanner is
switched on whenever the facial tanner is
switched on, but its power cannot be
decreased. When the facial tanner is switched
off, the shoulder tanner is also switched off.
Important: Do not operate the shoulder tanner without
lamp unit.
Level II: After the tanning program has been started,
the facial tanners are automatically turned on at the
maximum power level.
Level I: The power is reduced to level I by pressing the
“–” button. This level is not implemented in the KBL
5800 Super, Super Power and Ultra Power models of
UV type 3.
Level 0: The facial tanners are completely turned off by
pressing the “–” button again for a few seconds.
Use the “+” button to switch the tanners on again or to
increase their power.
After the tanners have been switched off, there is a time
delay before they can be switched on again because
the lamps must cool down first.