KIESELMANN 5714 User manual

Operating instructions - Translation of the original -
18.4.11
KIESELMANN GmbH
Paul-Kieselmann-Str.4-10
D - 75438 Knittlingen
 [phone]  Fax: [phone]
www.kieselmann.de  [e-mail]
Single seat valve
Two-way-valve
Type: 5714
pneumatic operation

18.4.11
Single seat - Two-way-valve Typ: 5714
2
1. List of contents ..............................................................................................................................2
2. Information for your safety.............................................................................................................3
3. Marking of security instructions in the operating manual ..............................................................3
4. Safety instuctions ..........................................................................................................................4
4.1 Field of application .............................................................................................................4
4.2 General safety instructions ................................................................................................4
4.3 General notes ....................................................................................................................4
5. Function.........................................................................................................................................4
5.1 Functional description ........................................................................................................4
6. Installation informations.................................................................................................................5
6.1 Installations instructions.....................................................................................................5
6.2 Welding guidlines...............................................................................................................5
7. Maintenance..................................................................................................................................5
7.1 Maintenance ......................................................................................................................5
7.2 Cleaning.............................................................................................................................5
8. Control system - and interrrogation system...................................................................................5
8.1 Control head - optional- .....................................................................................................5
8.2 Proximity switch mounting set -optional-............................................................................5
9. Technical data ...............................................................................................................................6
10. Pneumatic valve actuation ............................................................................................................7
10.1 Actuator: air open - spring close ........................................................................................7
10.2 Actuator: air close - spring open .......................................................................................7
10.3 Actuator: air open - air close ..............................................................................................7
11. Disassembly and assembly...........................................................................................................8
11.1 Removing the pneum. valve insert (air open/spring close) ................................................8
11.2 Removing the pneum. valve insert (air close/spring open) (air open/air close) ................8
11.3 Disassembly.......................................................................................................................8
11.4 Assembly ...........................................................................................................................8
12. Dimensions....................................................................................................................................9
12.1 Size measurement table ....................................................................................................9
12.2 Dimensioned drawing ........................................................................................................9
13. Drawings .....................................................................................................................................10
13.1 air open - spring close......................................................................................................10
13.2 air close - spring open......................................................................................................11
13.3 air open - air close ...........................................................................................................12
14. Manufacturing..............................................................................................................................13
14.1 Structure of Article number ..............................................................................................13
15. Spare parts list ............................................................................................................................15
16. Two-way-valve Type: 5714 (1.4404 / AISI316L) ........................................................................15
16.1 Valve insert VE ................................................................................................................15
16.2 Seal kit EPDM..................................................................................................................16
16.3 Seal kit HNBR ..................................................................................................................16
17. Declaration of incorporation ........................................................................................................17
1. List of contents

ak 12.1.11
Safety informations
3
2. Information for your safety
We are pleased that you have decided for a high-class KIESELMANN product. With correct application
and adequate maintenance, our products provide long time and reliable operation.
Before installation and initiation, please carefully read this instruction manual and the security advices
contained in it. This guarantees reliable and safe operation of this product and your plant respectively.
Please note that an incorrect application of the process components may lead to great material damages
and personal injury.
In case of damages caused by non observance of this instruction manual, incorrect initiation,
handling or external interference, guarantee and warranty will lapse!
Our products are produced, mounted and tested with high diligence. However, if there is still a reason
for complaint, we will naturally try to give you entire satisfaction within the scope of our warranty. We will
be at your disposal also after expiration of the warranty. In addition, you will also find all necessary instruc-
tions and spare part data for maintenance in this instruction manual. If you don't want to carry out the main-
tenance by yourself, our KIESELMANN service team will naturally be at your disposal.
3. Marking of security instructions in the operating manual
Hintsareavailableinthechapter"safetyinstructions"ordirectlybeforetherespectiveoperationinstruction.
The hints are highlighted with a danger symbol and a signal word. Texts beside these symbols have to
be read and adhered to by all means. Please continue with the text and with the handling at the valve only
afterwards.
Symbol Signal word Meaning
DANGER Imminent danger which may cause
severe personal injury or death.
ATTENTION
Dangerous situation which may
cause slight personal injury or
material damages.
NOTE
Marks application hints and other
information which is particularly
useful.

18.4.11
Single seat - Two-way-valve Typ: 5714
4
4. Safety instuctions
4.1 Field of application
Two-way-valves are utilised as a multiple valve in food and beverage as well as in pharmaceutical, bio-
technological and chemical industries.
4.2 General safety instructions
4.3 General notes
5. Function
5.1 Functional description
ATTENTION
• To avoid danger and damage, the fitting must be used in accordance with the safety instructions
and technical data contained in the operating instructions.
DANGER
• Danger of crushing or amputating limbs.
Do not reach into the valve housing when in pneumatic mode.
• Dismantling the valve or valve assemblies from the plant can cause injuries from fluids or gases
flowing out.
Dismantle the valve or valve assembly only when the plant has been rendered pressure-less and free of liquid and
gas.
• The spring preloaded valve insert (air open - spring close) may incur serious injuries by jumping out
of the housing.
Pneumatically open the valve before disassembling the clamp coupling, so that upstroke the piston
in direction “X“ (Fig. 5 /Page 10).
ATTENTION
• To avoid air leaking, only use pneumatic connection parts that have an o-ring seal facing the even
surface.
• When mounting the clamps, the max. torque must not be exceeded (see technical data).
• Steps should be taken to ensure that no external forces are exerted on the fitting.
NOTE
• All data are in line with the current state of development. Subject to change as a result of technical
progress.
• Function of
valve:
To guide liquid media optionally from one pipe to two pipelines separated from each
other and vice versa.(see Fig.1 and 2)
• Operation: Pneumatic lift drive and moved by spring force.
• Activation: 3/2-way solenoid valve.
Valve position A-D open
connection (U) closed
Valve position D-U open
connection (A) closed
Fig. 1 Fig. 2

18.4.11
Single seat - Two-way-valve Typ: 5714
5
6. Installation informations
6.1 Installations instructions
Preferably install the two way change-over valve vertically. Install the connection lines in such a way
as to permit the liquids to drain freely out of the housing.
Valves with welded ends that serve as connecting members can be directly welded to the piping.
6.2 Welding guidlines
Sealing elements integrated in weld components must generally be removed prior to welding.
To prevent damage, welding should be undertaken by certified personnel (EN287). Use the TIG (Tung-
sten Inert Gas) welding process.
7. Maintenance
7.1 Maintenance
The maintenance intervals depend on the operating conditions "temperature, temperature-intervals,
medium, cleaning medium, pressure and opening frequency". It is recommended to change the
leakage butterfly valve-seal annually. The maintenance intervals, however, depend on the condition of
the seals and are to be fixed by the user.
6Actuator
The actutator is maintenance-free and non-removable.
7.2 Cleaning
Cleaning of the upper and lower valve chabers is performed with the pipe cleaning system.
8. Control system - and interrrogation system
8.1 Control head - optional-
Optionally, modular valve control systems can be installed to the actuator for reading and actuating
valve positions. The standard version is a closed system with twofold limit position messaging (stan-
dard), with SPS, Interbus or ASI bus switch-on electronics, and integrated 3/2-way solenoid valves. For
tough operating conditions we recommend employing a stainless steel hood.
8.2 Proximity switch mounting set -optional-
For the acquisition of the valve positions over inductive initiators, a limit switch support is mounted on
the actuation. The enquiry takes place over the position of the piston rod.
NOTE
If installed horizontally, some minor residual liquids will remain in the ball-shape of the housing.
NOTE
Impurities can cause damage to the seals and seals area. Clean inside areas prior to assembly.
NOTE
Seal materials Lubricants
EPDM; Viton; k-flex
NBR; HNBR; Silicone
Thread
M
M
M
Klüber Paraliq GTE*
Klüber Paraliq GB 363*
Teflon grease Interflon*
*) It is only permitted to use approved lubricants, if the respective fitting is used for the production of food or drink. Please observe
the relevant safety data sheets of the manufacturers of lubricants.

18.4.11
Single seat - Two-way-valve Typ: 5714
6
9. Technical data
Model: Two-way-valve pneumatic operation
Valve size: NW 25 - 100
Connections: Welding end DIN11850 S2
Temperature range: • Ambient temperature:
• Product temperature:
• Sterilization temperature:
EPDM
HNBR
+4° to -+45°C
+0° to -+95°C medium dependent
+140°C short-time (30 min.)
+130°C short-time (30 min.)
Vaccum: 1,5 - 10
-6
mbar x
L
/
S
(test pressure 0,5mbar)
Control air pressure: 6,0 - 8,0 bar
Quality of control air: ISO 8573-1 : 2001 quality class 3
Material: in product contact not in product contact
Stainless steel type: 1.4404 / AISI316L 1.4301 / AISI304
1.4305 / AISI303
Surfaces: RA 0,8µm e-pol. metallic bright, e-pol.
Seals: EPDM (FDA)
HNBR (FDA)
HNBR
Nennweite DN
Operations pressures (bar):
(6bar Control air pressure)
DIN
INCH
25
1
40
1½
50
2
65
2½
80
3
100
4
Fig.1 Connection (U)
air open-spring close 10 10 10 6 10 7
air close - spring open 10 10 10 7,5 10 7,5
air open-air close 10 10 10 10 10 10
Connection (A-D)
air open-spring close 9996106
air close - spring open 555353
air open-air close 10 10 10 8 10 8
Fig.2 Connection (A)
air open-spring close 1,5 1,5 1,5 1 2 1,3
air close - spring open 555353
air open-air close 10 10 10 10 10 10
Connection (D-U)
air open-spring close 9996106
air close - spring open 99969,56
air open-air close 10 10 10 8 10 8
Clamp coupling: Nominal width NW
Tightening moment: DIN
INCH
25
1
40
1½
50
2
65
2½
80
3
100
4
Torque in Nm 15 15 15 25 20 55
Nominal width NW
Fluiddynamic measurement :
(accroding to DIN EN 60534-2-3)
DIN
INCH
25
1
40
1½
50
2
65
2½
80
3
100
4
A-D 12 35 65 101 153 170
D-A 12 35 65 101 153 180
D-U 23 46 84 138 220 270
U-D 25 48 82 140 220 270
* no value available

18.4.11
Single seat - Two-way-valve Typ: 5714
7
10. Pneumatic valve actuation
10.1 Actuator: air open - spring close
10.2 Actuator: air close - spring open
10.3 Actuator: air open - air close
Valve function pneumatic control with MV in control unit
(Fig. 3 /Page 7) pneumatic control with external solenoid valve (MV) (Fig. 3 /Page 7)
Valve “OPEN“
control air feed
P
➟ MV1 ➟ P1/LA2
Valve is opening by control air
control air feed
ext. MV
➟ LA2
Valve is opening by control air
Valve “CLOSED“
de-aeration
LA2/P1
➟ MV1 ➟ R
Valve is closing by spring
de-aeration
LA ➟ ext. MV
Valve is closing by spring
Valve function pneumatic control with MV in control unit
(Fig. 3 /Page 7) pneumatic control with external solenoid valve (MV) (Fig. 3 /Page 7)
Valve “CLOSED“
control air feed
P
➟ MV1 ➟ P1/LA1
Valve is closing by control air
control air feed
ext. MV
➟ LA1
Valve is closing by control air
Valve “OPEN“
de-aeration
P1/LA1
➟ MV1 ➟ R
Valve is opening by spring
de-aeration
LA1 ➟ ext. MV
Valve is opening by spring
Valve function pneumatic control with MV in control unit
(Fig. 3 /Page 7) pneumatic control with external solenoid valve (MV) (Fig. 3 /Page 7)
Valve “OPEN“
control air feed
P
➟ MV1 ➟ P1/LA1
Valve is opening by control air
control air feed
ext. MV
➟ LA1
Valve is opening by control air
Valve “CLOSED“
de-aeration
P
➟ MV3 ➟ P3/LA2
Valve is closing by control air
de-aeration
ext. MV ➟ LA2
Valve is closing by control air
air open - spring close spring open - air close air open - air close
MV = solenoid valve
R = de-aeration, sound absorber
P = compressed-air inlet (control unit)
LA = compressed air inlet (actuation)
S = slide switch - manual control
(solenoid valves)
I = initiatoren
H = angle bracket
E = de-aeration
LA = air connection
Fig. 3

18.4.11
Single seat - Two-way-valve Typ: 5714
8
11. Disassembly and assembly
11.1 Removing the pneum. valve insert (air open/spring close)
• Pneumatically open the valve, so that upstroke the piston (1) in direction X (Fig. 5 /Page 10).
• Remove clamp coupling (3).
• In an upward direction, dismount the complete valve insert from the valve.
11.2 Removing the pneum. valve insert (air close/spring open) (air open/air close)
• Remove clamp coupling (3).
• In an upward direction, dismount the complete valve insert from the valve.
11.3 Disassembly
6Exchanging „A“ Item. (D1), (D2), (D3), (D4).
• Loosen screw (7) and move the lantern (6) until the spanner flat (SW1) and the borehole (B1) is
visible.
• Unscrew piston (1) from piston rod (8) (SW1/B1).
• Slide off insert (2) with bearing bush (4), Seal (D3) and O-ring (D4) in opposite direction to the valve
side of the piston´s “X“.
• Replace seals and wearing parts.
6Exchanging „B“ Item. (D5).
• See - Dismantling exchanging seals „A“.
• Remove screw (7) and dismount the lantern (6).
• Screw off the thread connection Pos. (G1) of the piston rods (8) and the spindle (11) at the spanner
surfaces (SW1 und SW2).
• Remove axially the piston rod (8) and shaft (10) with spindle (11) from the lift drive.
• Replace the o-ring (D5) (2x).
11.4 Assembly
• Thoroughly clean and slightly lubricate mounting areas and running surfaces.
• Assemble in reverse order.
• Thread connection (G1) assembly with removeable screw retention (e.g. Loctite 243) .
• Assemble in reverse order.
• Check the valve function.
➣Lubricants
• EPDM; Viton; k-flex
Klüber Paraliq GTE 703
• NBR; HNBR; Silicone
Klüber Paraliq GB 363
• Thread
Teflongrease Interflon
NOTE
All threaded joint have right-hand thread.
Unscrew and remove control air, steam i.e. cleaning lines and electrical lines, complete proximity switch
mounting or control head.
NOTE
Puncture the o-ring (D1) and (D2) at the centre with a pointed tool and remove them carefully from
the groove.
NOTE
Alternately press and roll the seal (D1) and (D2) into the groove with round body.

18.4.11
Single seat - Two-way-valve Typ: 5714
9
12. Dimensions
12.1 Size measurement table
12.2 Dimensioned drawing
DN d1 d3 L1 L2 L3
25
1 INCH
26
22,1
29
25,4 75 36 401
40
1½ INCH
38
34,8
41
38,1 85 48 405
50
2 INCH
50
47,5
53
50,8 85 60 409
65
2½ INCH
66
60,2
70
63,5 105 76 430
80
3 INCH
81
72,8
85
76,1 115 91 531
100
4 INCH
100
97,4
104
101,6 130 110 559
Fig. 4

18.4.11
Single seat - Two-way-valve Typ: 5714
10
13. Drawings
13.1 air open - spring close
Fig. 5
1) Piston
2) Insert
3) Clamp coupling
4) Bearing bush
5) Washer screw retention
6) Lantern
7) Screw
8) Piston rod
9) Actuator
10) Shaft
11) Spindle upper
12) O-Ring
13) Position indication
14) Cap
D1) O-Ring
D2) O-Ring
D3) Seal
D4) O-Ring
D5) O-Ring
VG) Housing
IG) Pulse generator
A1) Proximity switch mounting
A2) Control head

18.4.11
Single seat - Two-way-valve Typ: 5714
11
13.2 air close - spring open
Fig. 6
1) Piston
2) Insert
3) Clamp coupling
4) Bearing bush
5) Washer screw retention
6) Lantern
7) Screw
8) Piston rod
9) Actuator
10) Shaft
11) Spindle upper
12) O-Ring
13) Position indication
14) Cap
D1) O-Ring
D2) O-Ring
D3) Seal
D4) O-Ring
D5) O-Ring
VG) Housing
IG) Pulse generator
A1) Proximity switch mounting
A2) Control head

18.4.11
Single seat - Two-way-valve Typ: 5714
12
13.3 air open - air close
Fig. 7
1) Piston
2) Insert
3) Clamp coupling
4) Bearing bush
5) Washer screw retention
6) Lantern
7) Screw
8) Piston rod
9) Actuator
10) Shaft
11) Spindle upper
12) O-Ring
13) Position indication
14) Cap
D1) O-Ring
D2) O-Ring
D3) Seal
D4) O-Ring
D5) O-Ring
VG) Housing
IG) Pulse generator
A1) Proximity switch mounting
A2) Control head

18.4.11
Single seat - Two-way-valve Typ: 5714
13
14. Manufacturing
14.1 Structure of Article number
6Product type
57xx = Single seat valve
6Housing type
6Valve size
DN = Nominal diameter
6Material seal / Construction modifications
6Material in product contact / Exterior finish
Two-way valve
S-S-S
5714 050 030 - 041
Material in product contact / Exterior finish / Interrogation system
Material seals in product contact / Construction modifications
Valve size
Housing type
Product type
DIN 025 = DN25 040 = DN50 050 = DN50 065 = DN65 080 = DN80 100 = DN100 125 = DN125 150 = DN150
Zoll
026 = DN1 038 = DN1½ 051 = DN2 064 = DN2½ 076 = DN3 101 = DN4 - -
Material seals in product contact: - EPDM
- HNBR
Construction modifications: Type of actuation - air open - spring close
- air open - air close
- spring open - air close
020 - 1.4301/1.4307 AISI304/307 - bright turned 040 - 1.4301/1.4307 AISI304/307 - bright turned
021 - 1.4301/1.4307 AISI304/307 - E-polished 041 - 1.4301/1.4307 AISI304/307 - E-polished
022 - 1.4301/1.4307 AISI304/307 - unpolished, glass-bead blasted 042 - 1.4301/1.4307 AISI304/307 - unpolished, glass-bead blasted

18.4.11
Single seat - Two-way-valve Typ: 5714
14
6Interrogation system
Article number Control System or Interrogation System (A1, A2) Pulse generator IG
57xx DN xxx -041 - ----- - - Valve without Control- or Interrogation System ------
57xx DN xxx
-750 Mounting 5630 005 000-020 - - Valve with Sensor mounting set ------
Control head ASi-Bus for Single seat valve
57xx DN xxx -600 Control head 5630 500 000-000 ASi-Bus Standard 0 MV ASI 2-wire cable adapter 5702 DN 005-000
57xx DN xxx
-601 Control head 5630 501 000-000 ASi-Bus Standard 1 MV ASI 2-wire cable adapter 5702 DN 005-000
57xx DN xxx
-602 Control head 5630 502 000-000 ASi-Bus Standard 2 MV ASI 2-wire cable adapter 5702 DN 005-000
57xx DN xxx
-603 Control head 5630 503 000-000 ASi-Bus Standard 3 MV ASI 2-wire cable adapter 5702 DN 005-000
57xx DN xxx
-604 Control head 5630 503 010-000 ASi-Bus/ES/ABSL 3 MV Plug M12 4-pin / plug socket M12 5-pin 5702 DN 005-000
57xx DN xxx
-605 Control head 5630 503 051-000 ASi-Bus/ABSL 3 MV Plug M12 4-pin, ES-LA 5702 DN 005-000
57xx DN xxx
-606 Control head 5630 501 010-000 ASi-Bus/ES/ABSL 1 MV Plug M12 4-pin / plug socket M12 5-pin 5702 DN 005-000
57xx DN xxx
-607 Control head 5630 501 051-000 ASi-Bus/ABSL 1 MV Stecker M12 4-pin, ES-LA 5702 DN 005-000
57xx DN xxx
-609 Control head 5630 503 050-000 ASi-Bus/ABSL 3 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-610 Control head 5630 502 010-000 ASi-Bus/ES/ABSL 2 MV Plug M12 4-pin / plug socket M12 5-pin 5702 DN 005-000
57xx DN xxx
-613 Control head 5630 502 051-000 ASi-Bus/ABSL 2 MV Plug M12 4-pin, ES-LA 5702 DN 005-000
57xx DN xxx
-614 Control head 5630 503 053-000 ASi-Bus/ABSL 3 MV ASI 2-wire cable adapter 5702 DN 005-000
57xx DN xxx
-615 Control head 5630 503 003-000 ASi-Bus Standard 3 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-616 Control head 5630 501 003-000 ASi-Bus Standard 1 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-619 Control head 5630 503 151-000 ASi-Bus/ABSL 3 MV Plug M12 4-pin, LED-ESH 5702 DN 005-000
57xx DN xxx
-620 Control head 5630 501 050-000 ASi-Bus/ABSL 1 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-624 Control head 5630 502 050-000 ASi-Bus/ABSL 2 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-625 Control head 5630 501 158-000 ASi-Bus/ABSL 1 MV KV M16x1,5, LED-ESH 5702 DN 005-000
57xx DN xxx
-626 Control head 5630 502 158-000 ASi-Bus/ABSL 2 MV KV M16x1,5, LED-ESH 5702 DN 005-000
57xx DN xxx
-627 Control head 5630 503 158-000 ASi-Bus/ABSL 3 MV KV M16x1,5, LED-ESH 5702 DN 005-000
57xx DN xxx
-628 Control head 5630 501 151-000 ASi-Bus/ABSL 1 MV Plug M12 4-pin, LED-ESH 5702 DN 005-000
57xx DN xxx
-629 Control head 5630 501 151-000 ASi-Bus/ABSL 1 MV Plug M12 4-pin, LED-ESH, ES-LA 5702 DN 005-000
57xx DN xxx
-630 Control head 5630 500 061-000 ASi-Bus Standard 0 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-631 Control head 5630 501 061-000 ASi-Bus Standard 1 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-632 Control head 5630 502 061-000 ASi-Bus Standard 2 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-633 Control head 5630 503 061-000 ASi-Bus Standard 3 MV Plug M12 4-pin 5702 DN 005-000
57xx DN xxx
-640 Control head 5630 501 058-000 ASi-Bus/ABSL 1 MV KV 2x M16x1,5 5702 DN 005-000
57xx DN xxx
-641 Control head 5630 502 058-000 ASi-Bus/ABSL 2 MV KV 2x M16x1,5 5702 DN 005-000
57xx DN xxx
-642 Control head 5630 503 058-000 ASi-Bus/ABSL 3 MV KV 2x M16x1,5 5702 DN 005-000
Control head SPS for Single seat valve
57xx DN xxx -500 Control head 5630 300 000-000 SPS-Standard 0 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-501 Control head 5630 301 000-000 SPS-Standard 1 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-502 Control head 5630 302 000-000 SPS-Standard 2 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-503 Control head 5630 303 000-000 SPS-Standard 3 MV KV M16x1,5 / Pg 9 5702 DN 005-000
57xx DN xxx
-504 Control head 5630 321 000-000 SPS-Standard 1 MV Plug M12 7-polig 5702 DN 005-000
57xx DN xxx
-505 Control head 5630 301 108-000 SPS-Standard 1 MV KV 2x M16x1,5 / Pg 9, LED-ESH 5702 DN 005-000
57xx DN xxx
-506 Control head 5630 302 108-000 SPS-Standard 2 MV KV 2x M16x1,5 / Pg 9, LED-ESH 5702 DN 005-000
57xx DN xxx
-507 Control head 5630 303 108-000 SPS-Standard 3 MV KV 2x M16x1,5 / Pg 9, LED-ESH 5702 DN 005-000
57xx DN xxx
-508 Control head 5630 301 100-000 SPS-Standard 1 MV KV M16x1,5 / Pg 9, ESH 5702 DN 005-000
57xx DN xxx
-510 Control head 5630 X00 040-000 SPS-Standard 0 MV KV M16x1,5 / Pg 9, Valve tag 5702 DN 005-000
57xx DN xxx
-513 Control head 5630 303 040-000 SPS-Standard 3 MV KV M16x1,5 / Pg 9, Valve tag 5702 DN 005-000
DN - Nominal diameter z.B. 5714 050 030-041
MV - Solenoid valve
KV - Compression gland 4,5-6mm
ESH - Stainless steel cap
ES-LA - Air connection (steel stainless)

18.4.11
Single seat - Two-way-valve Typ: 5714
15
15. Spare parts list
16. Two-way-valve Type: 5714 (1.4404 / AISI316L)
16.1 Valve insert VE
Seal Actuator Article-N0. Valve insert VE Housing VG Seal kit
EPDM lö - fs 5714 DN 030-xxx 5714 DN 020-041 5713 DN 031-041 5714 DN 990-054
fö - ls 5714 DN 130-xxx 5714 DN 023-041 5713 DN 031-041 5714 DN 990-054
lö - ls 5714 DN 330-xxx 5714 DN 026-041 5713 DN 031-041 5714 DN 990-054
HNBR lö - fs 5714 DN 035-xxx 5714 DN 021-041 5713 DN 031-041 5714 DN 990-050
fö - ls 5714 DN 135-xxx 5714 DN 024-041 5713 DN 031-041 5714 DN 990-050
lö - ls 5714 DN 335-xxx 5714 DN 027-041 5713 DN 031-041 5714 DN 990-050
DN = Nominal diameter e.g. 5673 050 130-041 = DN50 , 5673 051 130-041 = 2INCH
xxx = Interrogation system
lö = air open
ls = air close
fö = spring open
fs = spring close
Item Designation Material DN25
1 INCH DN40 1½ INCH DN50 2 INCH DN65 2½ INCH DN80 3 INCH DN100 4 INCH
VE
Valve insert lö - fs - DIN
-INCH
Valve insert fö - ls - DIN
-INCH
Valve insert lö - ls - DIN
-INCH
EPDM
5714 025 020-041
5714 026 020-041
5714 025 023-041
5714 026 023-041
5714 025 026-041
5714 026 026-041
5714 040 020-041
5714 038 020-041
5714 040 023-041
5714 038 023-041
5714 040 026-041
5714 038 026-041
5714 050 020-041
5714 051 020-041
5714 050 023-041
5714 051 023-041
5714 050 026-041
5714 051 026-041
5714 065 020-041
5714 064 020-041
5714 065 023-041
5714 064 023-041
5714 065 026-041
5714 064 026-041
5714 080 020-041
5714 076 020-041
5714 080 023-041
5714 076 023-041
5714 080 026-041
5714 076 026-041
5714 100 020-041
5714 101 020-041
5714 100 023-041
5714 101 023-041
5714 100 026-041
5714 101 026-041
VE
Valve insert lö - fs - DIN
-INCH
Valve insert fö - ls - DIN
-INCH
Valve insert lö - ls - DIN
-INCH
HNBR
5714 025 021-041
5714 026 021-041
5714 025 024-041
5714 026 024-041
5714 025 027-041
5714 026 027-041
5714 040 021-041
5714 038 021-041
5714 040 024-041
5714 038 024-041
5714 040 027-041
5714 038 027-041
5714 050 021-041
5714 051 021-041
5714 050 024-041
5714 051 024-041
5714 050 027-041
5714 051 027-041
5714 065 021-041
5714 064 021-041
5714 065 024-041
5714 064 024-041
5714 065 027-041
5714 064 027-041
5714 080 021-041
5714 076 021-041
5714 080 024-041
5714 076 024-041
5714 080 027-041
5714 076 027-041
5714 100 021-041
5714 101 021-041
5714 100 024-041
5714 101 024-041
5714 100 027-041
5714 101 027-041
1Piston -DIN
-INCH AISI316L
5714 025 002-040
5714 026 002-040 5714 040 002-040 5714 038 002-040 5714 050 002-040 5714 051 002-040 5714 065 002-040 5714 064 002-040 5714 080 002-040 5714 076 002-040 5714 100 002-040 5714 101 002-040
2Insert AISI316L 5622 050 005-040 5622 050 005-040 5622 050 005-040 5622 065 005-040 5622 080 005-040 5713 100 003-040
3Clamp coupling AISI316L 2122 065 100-020 2122 065 100-020 2122 065 100-020 2122 080 100-020 2122 115 100-020 2122125100-020
4Bearing bush AISI316L 5622 050 006-053 5622 050 006-053 5622 050 006-053 5622 065 006-053 5622 080 006-053 5622100006-053
5Washer screw retention AISI304 8135 012 195-040 8135 012 195-040 8135 012 195-040 8135 012 195-040 8135 012 195-040 8135012195-040
6Lantern AISI304 5706 050 010-021 5706 050 010-021 5706 050 010-021 5706 065 008-021 5706 080 008-021 5706100008-021
7Screw AISI316L
8095 010 020-020
M10x20 (2x) 8095 010 020-020 M10x20 (2x) 8095 010 020-020 M10x20 (2x) 8095 010 020-020 M10x20 (2x) 8106 008 016-020 M8x16 (4x) 8106 008 016-020 M8x16 (4x)
8Piston rod AISI304 5200 104 052-020 5200 104 052-020 5200 104 052-020 5200 104 052-020 5200 157 057-020 5200 157 057-020
9Actuator lö - fs
Actuator fö - ls
Actuator lö - ls
AISI304
AISI304
AISI304
5200 104 051-032
5400 104 051-032
5300 104 050-032
5200 104 051-032
5400 104 051-032
5300 104 050-032
5200 104 051-032
5400 104 051-032
5300 104 050-032
5200 104 051-032
5400 104 051-032
5300 104 050-032
5200 157 051-032
5400 157 051-032
5300 157 051-032
5200 157 051-032
5400 157 051-032
5300 157 051-032
10 Shaft AISI304 5200 104 053-020 5200 104 053-020 5200 104 053-020 5200 104 053-020 5200 157 056-020 5200 157 056-020
11 Spindle upper AISI303 5622 100 070-220 5622 100 070-220 5622 100 070-220 5622 100 070-220 5622 100 070-220 5622 100 070-220
12 O-Ring EPDM 2304 012 020-055 2304 012 020-055 2304 012 020-055 2304 012 020-055 2304 012 020-055 2304 012 020-055
13 Position indication ABS gn 5622 100 058-152 5622 100 058-152 5622 100 058-152 5622 100 058-152 5622 100 058-152 5622 100 058-152
14 Cap AISI303 5622 100 071-220 5622 100 071-220 5622 100 071-220 5622 100 071-220 5622 100 071-220 5622 100 071-220

18.4.11
Single seat - Two-way-valve Typ: 5714
16
16.2 Seal kit EPDM
16.3 Seal kit HNBR
Item Designation Material DN25
1 INCH DN40 1½ INCH DN50 2 INCH DN65 2½ INCH DN80 3 INCH DN100 4 INCH
Seal kit EPDM
5714 025 990-054 5714 040 990-054 5714 050 990-054 5714 065 990-054 5714 080 990-054 5714 100 990-054
D1 O-Ring EPDM 2304 041 035-159 2304 044 053-159 2304 044 053-159 2304 053 053-159 2304 069 053-159 2304 088 053-159
D2 O-Ring EPDM 2304 053 053-159 2304 053 053-159 2304 053 053-159 2304 069 053-159 2304 088 053-159 2304 113 053-084
D3 Seal EPDM 5622 050 010-069 5622 050 010-069 5622 050 010-069 5622 065 010-069 5622 080 010-069 5622 100 010-069
D4 O-Ring EPDM 2304 069 026-159 2304 069 026-159 2304 069 026-159 2304 082 026-159 2304 098 035-159 2304 118 045-055
D5 O-Rings (2x) HNBR 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171
Item Designation Material DN25
1 INCH DN40 1½ INCH DN50 2 INCH DN65 2½ INCH DN80 3 INCH DN100 4 INCH
Seal kit HNBR
5714 025 990-050 5714 040 990-050 5714 050 990-050 5714 065 990-050 5714 080 990-050 5714 100 990-050
D1 O-Ring HNBR 2304 041 035-050 2304 044 053-157 2304 044 053-157 2304 053 053-157 2304 069 053-157 2304 088 053-157
D2 O-Ring HNBR 2304 053 053-050 2304 053 053-157 2304 053 053-157 2304 069 053-157 2304 088 053-157 2304 113 053-157
D3 Seal HNBR 5622 050 010-050 5622 050 010-050 5622 050 010-050 5622 065 010-050 5622 080 010-050 5622 100 010-050
D4 O-Ring HNBR 2304 069 026-050 2304 069 026-150 2304 069 026-050 2304 082 026-050 2304 098 035-050 2304 118 045-050
D5 O-Rings (2x) HNBR 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171 2304 019 035-171

Knittlingen, 18. 04. 2011
Klaus Dohle
General Director
The manufacturer hereby states that the above product is considered as an incomplete machine in the sense defined
in the Directive 2006/42/EC on Machinery. The above product is exclusively intended to be installed into a machine or
an incomplete machine. The said product does not yet conform to all the relevant requirements defined in the Directive
on Machinery referred to above for this reason.
The specific technical documents listed in Appendix VII, Part B, have been prepared. The Authorized Agent empowered
to compile technical documents may submit the relevant documents if such a request has been properly justified.
Commissioning of an incomplete machine may only be carried out if it has been determined that the respective machine
into which the incomplete machine is to be installed conforms to the regulations set out in the Directive on Machinery
referred to above.
The above product conforms to the requirements of the directives and harmonized standards specified below:
Declaration of incorporation
Translation of the original
Manufacturer
/ authorised representative: KIESELMANN GmbH
Paul-Kieselmann-Str. 4-10
75438 Knittlingen
Germany
Authorised representative,
for compiling technical documents:
Achim Kauselmann
KIESELMANN GmbH
Paul-Kieselmann-Str. 4-10
75438 Knittlingen
Germany
Product name Function
pneum. Lift actuators
pneum. Rotary actuators
Ballvalves
Butterfly valves
Single seat valves
Flow control valves
Throttle valve
Overflow valve
Double seat valve
Bellow valves
Sampling valves
Two way valves
Tankdome fitting
Stroke movement
Rotary movement
Media cutoff
Media cutoff
Media cutoff
Control of liquified media
Control of liquified media
Definition of fluid pressure
Media separation
Sampling of liquids
Sampling of liquids
Media cutoff
Prevention of overpressure and vacuum
• DIN EN ISO 12100-1 Safety of machinery
• DIN EN ISO 12100-2 Safety of machinery