Kilews SKC-P25W User manual
1
Icon Explanation
Read manual Caution Double insulation Indoor use only No humidity
No fire No disassemble No disposal CE Certification
Caution
Please read all instructions carefully before operate the rechargeable battery and charger. Also please
follow all the instructions and pay attention to all the warring.
Important Notification
1. Please operate under the correct voltage to the charger in according with the operation manual.
2. When charging the battery, please make sure the grounding and safety components are properly attached
before operating.
3. The charger should store in clean and dry area. Do not place heave stuff on the charger. Please do not
charge the battery when the temperature is above 33℃.
4. Please do not place the charger in the poorly ventilated place, nor expose the charger in the dust or metal
crumb.
5. Do not expose the charger directly under sun, high temperature, high humidity , and highly explosive
gas.
6. Do not place charger on high shelf. The charger should be placed on the leveled, firmed spot that prevent
children from reaching.
7. Do not abuse the cord. Never use the cord to carry, pull or unplug the charger. Keep cord away from heat,
oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
8. Please read all instructions carefully before operate the charger. Failure to follow all instructions listed
below may result in electric shock fire and/or serious injure.
9. It is forbidden to use different brand of battery other then KILEWS’ on the charger. To disassemble and
modify the charge are also not allowed.
Grounding Instruction
The charger needs to be grounded all the time in case of electrical shock. The grounding wire must be
connected firmly with power supply equipment for effective grounding result. The leading wire with
yellow-green color is a grounding wire. Never attempt to connect this yellow-green color wire on electrified
connector.
2
Caution
1. Please match the correct Lithium-ion rechargeable battery for this charger, which is only manufacture by
Kilews. Do not apply different type or brand of battery on this charger, otherwise may cause error or
danger.
2. Please match the charger with the battery models. SKC-LB0730S. The use of other than genuine KILEWS
replacement parts or battery may result in decreased tool performance and increased maintenance, and may
invalidate all warranties.
3. Keep children, and bystanders away while charging the battery, in case of danger.
4. Please do not plug in the charger when the plug or users’ hand is wet.
5. To disassemble or modify the charger’s plug may cause danger or dysfunction.
6. This charger only applies to the rechargeable battery of Kilews. Please do not apply the charger to other
different brand of battery or for other propose.
7. Please do not attempt to disassemble or modify the charger and the rechargeable battery.
8. USB jack: To update the firmware and maintenance only, users can not use this function.
9. When the battery is fully charged and the charger LED status is displayed fully charged,
and if the battery is placed in the charger for two hours more, the charger will
continuously short beeps and the red and green lights flash to show that the battery is
fully charged. Please remove the battery from the charger.
Operation Instruction
1. Please check the cord to see if there any damage before plug in the charger. Hold the plug of power cord
while plugging in or unplug the charger.
2. Do not place chargers near oil, chemical materials or heated objects, also please be alert not to scratch the
power cord by sharp object.
3. When the charger is not in use, please unplug the power and store in dry safe place where it is not
reachable by children.
4. Charger and battery assemble
SKC-P25W
Assemble
Decomposition
1). The direction of battery when
removing.
2).Decomposition steps finished.
1). The direction of the battery when
insert, push all the way.
2). Assemble steps finished.
3
Caution: Protection Functions
1. Over charged protection
2. Current protection
3. Shortage protection (fuse implement)
4. Battery reverse current protection
5. SKC-P25W Built-in ID recognition feature protection
6. Temperature protection
Temperature protection detail explanation
(1) When the battery temperature is between 0-10℃, the charger will use low current to pre-charge the
battery until the battery temperature higher then 10℃ , then the charger switch back to normal charging
mode. When the battery temperature is below 0℃, the charger will stop charging the battery until the
battery temperature is higher then 0℃.
(2) When the battery temperature is above 45℃, the charger will automatically change to low current to charge
the battery. When the battery temperature is exceed 50℃, the charger will stop charging the battery and
make warning beep sound until the battery temperature drop down back to 40℃ , then the charger switches
back to normal charging mode.
(3) When the charger temperature rises to 75℃, the charger will trigger protection mechanism to stop charging
the battery and until the charger temperature drop down back to 65℃ , then the charger switches back to
normal charging mode.
(4) When the charger voltage is lower then 8V, the charger will automatically change to low current to
pre-charge the battery and until voltage is reach to 8V, then the charger switches back to fast charging
mode.
(5) When the charger detects the battery temperature is lower 0℃ or about 50℃, then the charging process
will be stopped. Automatically rechargeable
Contents
Charger stand
1 pcs
Power cord
1 pcs
Operation manual
1 pcs
Warranty certification
1 pcs
4
Display Description
Specification
Caution
SAVE THE INSTRUCTIONS
DO NOT DESTROY
Light Display and
Warning Beep
Description Beeps
Red
light
Yellow
light
Green
light
Cell balance
N/A
OFF
Flash
OFF
Charging under 80%
N/A
Flash
OFF
OFF
Charging over 80%~99%
N/A
Flash
ON
OFF
Charging Complete100%
Three long beeps
ON
OFF
ON
Charging Error
Continuous short beeps
Flash
OFF
Flash
ID matched OK
One second short B sound
----
----
----
ID matched NG
N/A
Flash
OFF
Flash
Idle mode
N/A
ON
OFF
OFF
Model
Charger Station
SKC-P25W
Battery Identification Yes
Input Voltage
100V – 240V
Output Voltage 8.4VDC
Output Current 3A
Dimension (W
＊
L
＊
H )
115mm
＊
145mm
＊
101.6mm
Weight 430.4g
Battery Type Li-ion
Applicable Battery Models
SKC-LB0730S
Charging Time Prox. 70min
Battery Capacity 3000 mA/hr
Light Display
Our company reserves the right to modify
the product without prior notice.
KILEWSINDUSTRIALCO..LTD.
CUSTOMER
ITEM NO:
TITLE:
DWG NAME
DWG NO:
MATERIAL
DES. BY
CHKD.BY
APPD.BY
SHRINK
DATE
DATE
DATE
PRODUCTION NO.
THIRD ANGLE PROJECTION.
UNITSCALESHT NO.
OF SHTS.
MODELNO:
SKC-P25W
Table of contents
Other Kilews Batteries Charger manuals
