KISANKRAFT KK-SRT-910D User manual

KisanKraft®
Warranty Certificate
(KISANKRAFT COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80.22178200
Page 88 of 88
Important: (1) Normal maintenance and adjustments to the product is the
responsibility of thecustomer. (2) Normal wear and tear is not covered under warranty.
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell,
spark-plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the
warranty.
No Warranty On Electrical Motor / Electrical Parts / Battery Etc.
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be
liable for general damages, including bodily injuries, or for incidental or consequential
damages including, but not limited to, loss of use, loss of profits, loss of production,
expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including, but
not limited to, any implied warranty of merchantability shall be limited in duration to the
applicable warranty period. Any action for breach of any warranty hereunder,
including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter the
obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not
transfer if the product is resold by the first buyer. The above warranties are extended
to the first end user (original purchaser), and no warranty is made, nor authorized to
be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of
any obligation under this warranty for failure during the applicable warranty period,
deliver the defective product, to the nearest Authorized Dealer. KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s)
to determine if the malfunction isthe result of a defect covered by this warranty. Please
note that the decision of KisanKraft Machine Tools Pvt Ltd with respect to any warranty
claim is final.
Receipt is required for availing warranty services
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Our
Products
ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand ToolsGardenTools 
Cultivators and AccessoriesSprayers and Accessories
Transplanter and Post Hole Digger Milking Machines
KisanKraft®
Warranty Certificate
(DEALER COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 1 of 88
Product
Agricultural
Inter-Cultivator
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-SRT-910D
KK-SRT-910E
WARRANTY
PERIOD
6MONTHS
FOR THE SPECIFIED PERIOD FROM THE
DATE OF SALE OR DELIVERY WHICHEVER IS
EARLIER.
Dealer’s
Invoice Date
Dealer’s Invoice
No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s Sign
Dealer’s Sign
What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of machine
or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical damage,
(6) Repairs made by unauthorized parties and/or with unauthorized parts, (7) Improper
set up, adjustments, tampering or altered products
Note: The purchase is not contingent upon a product demonstration. The
purchaser shall satisfy himself with the product, including any product
demonstration or verification of any function, before buying. KisanKraft Limited or
its authorized dealers, including online sellers, shall not be liable to give any on-site
demonstration after purchase of any of the product.

KisanKraft®
Warranty Certificate
(DEALER COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 2 of 88
Important: (1) Normal maintenance and adjustments to the product is the responsibility
of the customer. (2) Normal wear and tear is not covered under warranty
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell, spark-
plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the warranty.
No Warranty On Electrical Motor / Electrical Parts / Battery Etc.
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be
liable for general damages, including bodily injuries, or for incidental or consequential
damages including, but not limited to, loss of use, loss of profits, loss of production,
expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including, but
not limited to, any implied warranty of merchantability shall be limited in duration to the
applicable warranty period. Any action for breach of any warranties hereunder,
including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter the
obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not
transfer if the product is resold by the first buyer. The above warranties are extended to
the first end user (original purchaser), and no warranty is made, nor authorized to be
made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of any
obligation under this warranty for failure during the applicable warranty period, deliver
the defective product, to the nearest Authorized Dealer. KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s)
to determine if the malfunction is the result of a defect covered by this warranty. Please
note that the decision of KisanKraft Machine Tools Pvt Ltd with respect to any warranty
claim is final.
Receipt is required for availing warranty services
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Our
Products
ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand ToolsGardenTools
Cultivators and AccessoriesSprayers and Accessories
Transplanter and Post Hole Digger Milking Machines
KisanKraft®
Warranty Certificate
(KISANKRAFT COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 87 of 88
Product
Agricultural
Inter-Cultivator
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-SRT-910D
KK-SRT-910E
WARRANTY
PERIOD
6MONTHS
FOR THE SPECIFIED PERIOD FROM THE
DATE OF SALE OR DELIVERY WHICHEVER
IS EARLIER.
Dealer’s
Invoice Date
Dealer’s Invoice
No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s
Sign
Dealer’s Sign
What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of
machine or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical
damage, (6) Repairs made by unauthorized parties and/or with unauthorized parts, (7)
Improper set up, adjustments, tampering or altered products
Note: The purchase is not contingent upon a product demonstration. The
purchaser shall satisfy himself with the product, including any product
demonstration or verification of any function, before buying. KisanKraft Limited or
its authorized dealers, including online sellers, shall not be liable to give any on-
site demonstration after purchase of any of the product.

KisanKraft®
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 86 of 88
Wide Range of Products for Every Need
For more information give MISSED CALL: 07676065555
Many of our products have BIS: ISI certification.
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 3 of 88
User Manual
KisanKraft Limited
(Formerly known as KisanKraft Machine Tools Pvt Ltd)
Sri Huchhanna Tower, #4,1st Main,7-A Cross, Maruthi Layout, Dasarahalli,
HAF Post, Hebbal, Bangalore 560024,Karnataka,INDIA
♦Bangalore (HO) ♦ Ahmedabad ♦ Bhopal ♦ Bhubaneswar ♦ Coimbatore ♦
♦Jammu ♦ Guwahati ♦ Hubli ♦ Hyderabad ♦ Jaipur ♦
♦Karnal ♦ Kolkata ♦ Lucknow ♦ Pune ♦ Raipur ♦ Shimla ♦

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 4 of 88
CONTENTS
BEFORE GETTING STARTED................................................................................... 7
APPLICATION AND FEATURES............................................................................... 7
SAFETY INSTRUCTIONS......................................................................................... 8
PARTS DESCRIPTION ...........................................................................................15
FUNCTIONS OF DIFFERENT UNITS........................................................................19
RIGHT OPERATION & USE....................................................................................24
METHOD OF STARTING & SHUTTING DOWN THE ENGINE ...................................27
METHODS OF ADVANCE, TURNING, SPEED CHANGE & STOPPING: ......................29
CORRECT OPERATION: ........................................................................................31
CORRECT ASSEMBLY AND USE.............................................................................33
TECHNICAL SPECIFICATIONS................................................................................35
MAINTENANCE ...................................................................................................36
TROUBLESHOOTING............................................................................................46
PARTS DIAGRAM & PARTS LIST ...........................................................................47
KisanKraft®
PRODUCT RANGE
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 85 of 88
KisanKraft has a large range of products to serve the farmers. A list of our products
is given below:
Brush Cutters and Accessories
Brush Cutter/Power Weeder
Backpack Brush Cutter
Tea Pruner
Pole pruner with Engine
Reaper Attachment
Blades-Circular
Blades (2 &3 points)
Baffle
Nylon Rope
Tap & Go
Chainsaws
Petrol Chainsaw
Electric Chainsaw
Chain Sharpening Machine
Engines and Water Pumps
Engine –Diesel-(Horizontal)
Engine –Diesel(Vertical)
Engine-Kerosene
Water Pump with Petrol Engine
Water Pump with Kerosene Engine
Water Pump with Diesel Engine
Hand Tools
Secateurs
Folding Saw
Garden Rake
Garden Shovel
Hedge Shear
Lopper
Telescopic Hedge Shear
Telescopic Lopping Shear
Tree Pruner
Telescopic Steel Pipe & Fruit Picker Bag
Sheep Shear
Garden Tools
Electric Pressure Washer
Hedge Trimmer
Lawn Mower (Electric, Petrol & Manual)
Leaf Blower
Cultivators and Accessories
Petrol and Diesel
Sprayers and Accessories
BatterySprayer
Portable Power Sprayer
Trolley Sprayer
Manual Knapsack Sprayer
Manual Pressure Sprayer
Rose Cans
Hose Crimping Machine
HTP Sprayer
HTP Delivery Hose
HTP Hose Reel
HTP Stand
HTP Gun / Lance(Brass Rod
Knapsack Power Sprayer
Mister / Duster / GranuelSpreader
HTP Sprayer Set with Diesel Engine
HTP Sprayer Set with Kerosene Engine
Fogging Machine
Milking Machine
Wood Shredder
Fodder Ensiling Chaff Cutter
Fodder Grinder Chaff Cutter
Fodder Mini Chaff Cutter
Harvester
Maize Sheller
Maize Sheller + Dehusker
Maize Combine Harvester
Onion Digger Carlotti Italy
Tea Leaf Harvester
Sugarcane Combine Harvester
Sugarcane Leaf Stripper
Transplanter and Post Hole Digger
Paddy Transplanter (2 & 8 Rows)
Transplanter-Vegetable & Tobacco
Post Hole Digger(4” to 14”Augers)

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 84 of 88
8-7.Unit of Driving Chain of Output Shaft
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Welded parts
between back cover
of chain box and
supporting frame
GYR8-7-01
7
Bolt M8 x 12
GYR8-7-07
2
Chain 10A-1 x 56
GYR8-7-02
8
Connecting
bolt
GYR8-7-08
3
Small chain wheel
GYR8-7-03
9
Big chain
wheel
GYR8-7-09
4
Limit gasket
GYR8-7-04
10
Assembly of
hand wheel
GYR8-7-10
5
Split retainer 9
GYR8-7-05
11
Washer 12-
Spring
GYR8-7-11
6
Welded parts of
outer cover
GYR8-7-06
12
Washer 12-
Plain
GYR8-7-12
KisanKraft®
Warranty Certificate
(CUSTOMER COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 5 of 88
Product
Agricultural
Inter-Cultivator
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-SRT-910D
KK-SRT-910E
WARRANTY
PERIOD
6MONTHS
FOR THE SPECIFIED PERIOD FROM THE
DATE OF SALE OR DELIVERYWHICHEVER IS
EARLIER.
Dealer’s
Invoice Date
Dealer’s Invoice
No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s Sign
Dealer’s Sign
What is covered: KisanKraft Limited and its manufacturers warrant this product to be
free from defects in material or workmanship. All parts defective in material and
workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its
manufacturers at the premises of Authorized Dealers, of such parts as appear to
KisanKraft or its manufacturers, upon inspection, to be defective in material and/or
workmanship. KisanKraft or its manufacturers make no warranty with respect to trade
accessories not manufactured or sold by them.
What is not covered: The warranty shall become null and void and neither KisanKraft
Limited nor any of its manufacturers, nor its authorized dealers assumes any
responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of
machine or misuse, (3) Lack of maintenance, (4) Negligence, (5) Accident or physical
damage, (6) Repairs made by unauthorized parties and/or with unauthorized parts, (7)
Improper set up, adjustments, tampering or altered products.
Note: The purchase is not contingent upon a product demonstration. The
purchaser shall satisfy himself with the product, including any product
demonstration or verification of any function, before buying. KisanKraft Limited or
its authorized dealers, including online sellers, shall not be liable to give any on-
site demonstration after purchase of any of the product.

KisanKraft®
Warranty Certificate
(CUSTOMER COPY)
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
KisanKraft Limited (formerly known as KisanKraft Machine Tools P Ltd)
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 6 of 88
Important: (1) Normal maintenance and adjustments to the product is the
responsibility of the customer. (2) Normal wear and tear is not covered under
warranty.
(3) Rubber/plastic parts and consumables such as blades, clutch and clutch-bell,
spark-plugs, nylon line, air-filters, fuel-filters, oil seals etc. are not covered under the
warranty.
No Warranty On Electrical Motor / Electrical Parts / Battery Etc.
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not
be liable for general damages, including bodily injuries, or for incidental or
consequential damages including, but not limited to, loss of use, loss of profits, loss
of production, expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warrantyis inlieu ofall other express warranties,
obligations, or liabilities. Any implied warranties, obligations or liabilities, including,
but not limited to, any implied warranty of merchantability shall be limited in duration
to the applicable warranty period. Any action for breach of any warranty hereunder,
including, but not limited to, anyimplied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of
KisanKraft Limited or any of its manufacturers has the authority to increase or alter
the obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall
not transfer if the product is resold by the first buyer. The above warranties are
extended to the first end user (original purchaser), and no warranty is made, nor
authorized to be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of
any obligation under this warranty for failure during the applicable warranty period,
deliver the defective product, to the nearest Authorized Dealer. KisanKraft Limited,
its manufacturers and its dealers reserve the right to inspect the claimed defective
part(s) to determine if the malfunction is the result of a defect covered by this
warranty. Please note that the decision of KisanKraft Machine Tools Pvt Ltd with
respect to any warranty claim is final.
Receipt is required for availing warranty services
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Our
Products
ChainsawsBrush Cutters and AccessoriesHarvesters
Engines and Water PumpsHand ToolsGardenTools
Cultivators and AccessoriesSprayers and Accessories
Transplanter and Post Hole Digger Milking Machines
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 83 of 88
8-6 Unit of Tail Wheel
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Nut M10 x 1.25
GYR8-6-01
8
Welded parts
of crank
GYR8-6-08
2
Core shaft of tail
wheel
GYR8-6-02
9
Nut M8
GYR8-6-09
3
Assemble of tail
wheel
GYR8-6-03
10
Tensile
spring ring
GYR8-6-10
4
Welded parts of tail
wheel support
GYR8-6-04
11
Handle of
crank
GYR8-6-11
5
Welded parts of
screw
GYR8-6-05
12
Washer 10
GYR8-6-12
6
Washer 12
GYR8-6-06
13
Bolt M10 x
1.25 x 70
GYR8-6-13
7
Welded parts of
outer sheath
GYR8-6-07

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 82 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
12
Bearing 6104
GYR8-4-12
30
Stop
Ring/Retainer
62
GYR8-4-30
13
Teeth clutch
GYR8-4-13
31
Assemble of oil
sealing
GYR8-4-31
14
Input shaft
GYR8-4-14
32
Bolt M6 x 15
GYR8-4-32
15
Paper gasket ( I )
GYR8-4-15
33
Welded parts of
left housing
GYR8-4-33
16
Active chain
GYR8-4-16
34
Welded parts of
fork
GYR8-4-34
17
Sheath gasket
GYR8-4-17
35
0-seal ring 6.9
x 1.8G
GYR8-4-35
18
Chain 10A-1 x 64
GYR8-4-18
8-5 Assemble Of Left Movable Fender
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Rubber baffle
(middle)
GYR8-5-01
8
Rubber plate
GYR8-5-08
2
Adjusting plate
GYR8-5-02
9
Supporting
gasket
GYR8-5-09
3
Welded parts of
fender
GYR8-5-03
10
Hexagram nut
M6
GYR8-5-10
4
Screw M6 x 12
GYR8-5-04
11
Buy GYR8-5-5
GYR8-5-5
5
Welded parts of
linker Assy
GYR8-5-05
12
Elastic pin
GYR8-5-12
6
Elastic pin
GYR8-5-06
13
Pin shaft B8 x
30
GYR8-5-13
7
Buy GYR8-5-5
GYR8-5-05
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 7 of 88
BEFORE GETTING STARTED
We wish to thank you for choosing our product. We are confident that the high quality of
our product will meet your requirement and will give you long-lasting service. This manual
contains valuable information about our Intercultivator. It has been carefully prepared to
give you helpful suggestions for operating, adjusting, and servicing. Keep this manual in
a convenient place for quick and easy reference. Study it carefully, only with proper care
and operation you can expect to receive the long lasting service of this Intercultivator.
It is the owner’s and/or operator’s responsibility to
Read and understand the information contained in this manual.
Operate, lubricate, assemble and maintain the equipment in accordance with all
instructions and safety procedures in this manual.
Inspect the equipment and replace or repair any parts that are damaged or worn
which could cause damage to other parts, or cause a safety hazard.
The warnings, cautions and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
APPLICATION AND FEATURES
The purpose of cultivating the soil is to improve its structure, restore its fertility,
improve the surface conditions of the fields and provide a good foundation for the
sowing, growth and ripening of the crops during various stages.
Intercultivator covers all kinds of operations, from plowing, deep scarification, soil
crushing, ditch digging, bedding, film laying, weeding, hilling up, pesticide
spreading, harvesting, etc.
Intercultivator is a new type of cultivating machine that can do all the above
cultivating operations. The designers have taken full consideration of the different
requirements of different crops for cultivating tools, so that the machine canmeet
different conditions and perform wonderfully in dry fields, paddy fields, hilly
regions, flat areas and big sheds. It can work with high efficiency and perfect
results in fields or gardens for vegetables, fruits, flowerbeds, seedlings, tobacco,
tea and herbs. It is equally good for common crops and cash crops. It can
effectively reduce labour intensity, improve working efficiency and bring in more
income.
You will be able to use the machine to the best if you are familiar with the
instructions in this manual and operate the machine correctly.
NOTE: THIS MACHINE IS MEANT ONLY FOR SOFT SOIL USE.
STRICTLY PROHIBITED FOR HARD SOIL.

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 8 of 88
SAFETY INSTRUCTIONS
Please read and follow the safety instructions given below. Failure to do so may result in
serious damage or even accidents, including personal injury or death.
1. Safety Precautions during Operation:
Operators in any of the following cases must
be prevented from operating the machine.
If the operator is tired or sick and
unfit for operating the machine.
If the operator is drunk.
If the operator is pregnant.
If the operator is young (below 16
years)
Operators must be well protected before
operating the machine.
They must wear safety shoes.
They must wear safety caps.
Anything tied around their bodies
must be kept tight without leaving
any part hanging out.
They must not wear scarves,
kerchiefs, or aprons that might have
the danger of getting caught in the
machine.
Anybody borrowing the machine must be
instructed to read this manual carefully.
Otherwise it might lead to serious damage,
accidents, injury or causalities.
Ploughshares that do not match must not be
assembled on this machine, even after
modification. Otherwise it might lead to faults,
accidents or even deaths.
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 81 of 88
8-4 Assemble of Gearbox
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Spring
GYR8-4-01
19
Bearing 6204
GYR8-4-19
2
Fork arm
GYR8-4-02
20
Nut M6
GYR8-4-20
3
Block
GYR8-4-03
21
Born frame oil
sealing (F)
B20x40x7D)
GYR8-4-21
4
Slot nut M 10
GYR8-4-04
22
Stop
Ring/Retainer
20
GYR8-4-22
5
Split pin 2 x 20
GYR8-4-05
23
Welded parts of
right housing
GYR8-4-23
6
Born frame oil
sealing (F)
B20x35x7D
GYR8-4-06
24
Nut M10
GYR8-4-24
7
Welded parts of
flexible shaft
fixed frame
GYR8-4-07
25
Welded parts of
knife
GYR8-4-25
8
Dust proof cover
GYR8-4-08
26
Welded parts of
plough knife
shaft
GYR8-4-26
9
Bearing stand
GYR8-4-09
27
Bearing 6206
GYR8-4-27
10
Oil filling Plug
GYR8-4-10
28
Bolt M10 x 15
GYR8-4-28
11
Paper gasket (II)
GYR8-4-11
29
BoIt M6 x 20
GYR8-4-29

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 80 of 88
8-3 Assemble Parts of Fixed Fender
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Hexagram nut M6
GYR8-3-01
10
Back plastic
fender
GYR8-3-10
2
Press plate (II)
GYR8-3-02
11
Nut
GYR8-3-11
3
Front plastic fender
GYR8-3-03
12
Sheath
GYR8-3-12
4
Boll M6 x 12
GYR8-3-04
13
Spring
GYR8-3-13
5
Welded parts of left
movable sub-plate
GYR8-3-05
14
Link shaft
GYR8-3-14
6
Welded parts of left
movable main-plate
GYR8-3-06
15
Supporting
plate
GYR8-3-15
7
Welded parts of right
movable main-plate
GYR8-3-07
16
Limit plate
GYR8-3-16
8
Welded parts of left
movable sub-plate
GYR8-3-08
17
Press plate (
I )
GYR8-3-17
9
Spring cylinder pin 2
x 20
GYR8-3-09
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 9 of 88
2. Cautions That Must Be Taken Before Operating This Machine:
Refilling can be done only after the engine has
cooled down. Smoking must be prohibited and flame
must not be brought near, in the process of refilling.
Violation of this rule might lead to serious fire.
During winter time, when the machine is to be
started indoors, good ventilation must be
maintained, as there is a chance for contaminated
air affecting health or may lead to poisoning.
Every day before starting the machine, care must be
taken to remove the weeds or debris that get caught
around the muffler or engine, because they might
lead to overheat and damage the machine. At the
same time, all covers or caps must be checked
carefully to make sure that they are kept tight and
free from debris.
Every day, before operation, the machine, must be
checked carefully to see if the clutch control levers
and other controls can move freely. Adjustment
must be made if they cannot be operated safely and
reliably. Otherwise, mechanical faults or accidents
might occur.
3. Cautions in the Process of Loading and Unloading
The steering handles or the main clutchcontrol lever
must never be operated when the machine is
running on a stepping board.
At the time of using the machine to load and
unload with the help of a stepping board, it must be
operated at the lowest speed. The operator must not
take a turning, or change the route or stop on the
board. Operation of the steering handles and main
clutch control lever must not be put in the “neutral”
(idle) position. Stop the machine immediately
should any emergency occur. Otherwise accidents
such as falling down might happen.

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 10 of 88
The stepping board must have sufficient strength,
proper length or width.
When the machine is used to load and unload,
the operation must be done at flat and safe places.
The engine must be stopped and the body of the
truck must be fixed tight. The stepping board used
must have sufficient length, width and strength.
Slippery boards must not be used to prevent
accidents.
At the time of loading and unloading, nobody must
be allowed to stand in front of the machine. Else
injury or even death might result.
Heading forward at the time of going up and
backward at the time of coming down. At the same
time, the machine must be tied to the truck with a
rope.
At the time of loading, the machine must be
operated in the forward direction and at the time of
unloading, it must be operated in the reverse
direction. In the process of transportation when the
machine is put on a truck, it must be fixed with a
rope to prevent falling down
4. Precautions during the Process of Operation:
A stepping board must be used when the machine is
crossing a water ditch or a ridge in the fields.
When the machine enters a paddy field, crosses
a water ditch or a place where the soil is too soft, a
stepping board must be used. The machine must run
at the lowest speed, and the stepping board must have
proper length, width and strength that can meet the
operation of this machine. The steering handles, the
main clutch control lever or the main speed change
lever must not be operated. Otherwise there might be
a slip or tilt over of the machine, which might lead to
serious damage or accidents.
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 79 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Left knife
GYR8-1-01
8
Welded parts of
main sleeve for
rotary cultivation
knife
GYR8-1-08
2
Bolt M10 x 20
GYR8-1-02
9
Right knife
GYR8-1-09
3
Bend knife(II)
GYR8-1-03
10
Nut M8
GYR8-1-10
4
Welded parts of
sub-sheath for
rotary cultivation
GYR8-1-04
11
Washer 8
GYR8-1-11
5
Bend knife(I)
GYR8-1-05
12
Bolt M8 x 20
GYR8-1-12
6
Washer 10
GYR8-1-06
13
Elastic split pin
GYR8-1-13
7
Nut M1O
GYR8-1-07
14
Shaft pin B10 x
45
GYR8-1-14
8-2 Assemble Parts of Flexible Shaft for Rotary Cultivation Tractor
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Cable Sub Gyro
Tiller
GYR8-2-01
5
Washer 6
GYR8-2-05
2
Welded parts of
pull lever Assy
GYR8-2-02
6
Split pin 2 x
16
GYR8-2-06
3
GYR8-2-02
4
GYR8-2-02

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 78 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
5
Welded parts of
hanging and connecting
frame
GYR8-05
20
Washer 8
GYR8-20
6
Washer 10
GYR8-06
21
Washer 8
GYR8-21
7
Nut M10
GYR8-07
22
Washer 8
GYR8-22
8
Assemble of gearbox
for rotary cultivation
tractor
GYR8-08
23
Butterfly
nut M8
GYR8-23
9
Welded parts of main
beam
GYR8-09
24
Assemble
of Left
movable
fender
GYR8-24
10
Fixed seat
GYR8-10
25
Assemble
of fixed
fender
GYR8-25
11
Assemble of knob
GYR8-11
26
Elastic slit
pin
GYR8-26
12
Assemble of right
movable fender
GYR8-12
27
Bolt M 10 x
75
GYR8-27
13
Welded parts of tail
wheel frame
GYR8-13
28
Assemble
of left and
right rotary
cultivation
knife
GYR8-28
14
Assemble of screw
locking (III)
GYR8-14
29
Shaft pin
B10 x 45
GYR8-29
15
Assemble of screw
locking (II)
GYR8-15
8-1 Assemble Parts of Knife for Left and Right Rotary Cultivation
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 11 of 88
The machine must not be moved forward abruptly at
high speed, abruptly stopped, or abruptly turned. It
must not be operated at over high speed.
The machine must be started and stopped slowly,
and must be slowed down when it goes around a
turning. On downward slopes or rugged roads, it must
be slowed down too. Otherwise, damage or accidents
might result.
Mind steps on the road while running the machine.
In the countryside, on roads where there are water
ditches or theirsides present aslope shape, good care
must be taken of the steps on the roads. Otherwise the
machine might fall down.
Never operatethe intercultivator or any other operating
machines when the machine is running.
In operations using the intercultivator, never
operate it when the main machine is operating.
Otherwise the operator might be caught by the
intercultivator blades, which might lead to injury or
causalities
On rugged or soft roads or roads with crosswise water
diches, the machine must be operated at very low
speeds.
When the machine is going on a downward slope
or on rugged roads or on roads with many crosswise
water ditches, it must be operatedslowly. Otherwise, it
might have the risk of falling over, falling down or
having other accidents.
While operating the machine, the operator must not
turn his eyes to other things or let go his hands.
While operating the machine, the operator must
pay attention only on the operation. He must not turn
his eyes to other things or let go his hands. Otherwise,
accidents might occur.

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 12 of 88
The operator must not put his hands or feet under the
intercultivator or any other operating machinewhile the
engine is running. Otherwise injury or death might
occur.
The working place must be ventilated when the
machine is operated indoors.
When the machine is operated inside a big shed
or indoors, special attention must be paid to good
ventilation, especially during winters. Otherwise the air
emission might be harmful to the health or even cause
injury.
The operator must not stand and operate behind the
intercultivator when it is backing.
As shown in the picture, the claws of the
intercultivator are rotating in front of the operator while
he is operating the machine in the backward direction.
This is strictly prohibited. He must turn the handle
around at 180 degrees and move forward. Otherwise,
he may have the danger of being caught between the
machine and an obstacle, and should there be a tilling,
he might be caught into the intercultivator. In both
cases, serious injury might result.
Other people or animals must not get near the
machine.
While the machine is in operation, other people,
children in particular, or animals must be kept at a
distance. Otherwise unexpected accidents or injury
might occur.
Particular attention must be paid to unexpected
accidents when the machine is moving at high speed
or abruptly.
While operating the intercultivator or performing
any half-axis operations, take particular care because
the intercultivator might jump up unexpectedly when it
suddenly strikes against a hard ground or a stone while
moving fast or abruptly. Particularly, when the machine
is working by a river, a ditch or a cliff or some people
are nearby, serious injury or dropdown might occur.
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 77 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
18
Pin
SP 5-18
38
Upper
connecting
plate of grid
SP 5-38
19
Welded parts of fixed
position for side
cultivation
SP 5-19
39
Welded parts
of grid
SP 5-39
20
Washer 10
SP 5-20
40
Welded parts
of middle grid
SP 5-40
8. Unit of Rotary Cultivation Tractor
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Assemble of flexible
shaft for rotary
cultivation tractor
N/A
16
Unit of tail
WheeI
GYR8-16
2
Bolt M10 x 85
GYR8-02
17
Spring
GYR8-17
3
Washer 10
GYR8-03
18
Bolt M 8 x
20
GYR8-18
4
Assemble of screw
locking
GYR8-04
19
Nut M8
GYR8-19

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 76 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Welded parts of
pendulum shaft for
amplitude modulation
SP 5-01
21
Hexagram slot
nut MI0
SP 5-21
2
Welded parts of
hanging and
connecting under grid
SP 5-02
22
Welded parts
of screw for
depth of
cultivation
SP 5-22
3
Phillips screw M6x2
SP 5-03
23
Welded parts
of plough post
SP 5-23
4
Nut M6
SP 5-04
24
Welded parts
of handle
Iever for
amplitude
modulation
SP 5-24
5
Washer 6
SP 5-05
25
Bolt M8 x 15
SP 5-25
6
Riveted parts of plough
SP 5-06
26
Nut M8
SP 5-26
7
Bolt M12 x 65
SP 5-07
27
Washer 8
SP 5-27
8
Spring
SP 5-08
28
Limit plate of
amplitude
modulation
SP 5-28
9
Welded parts of
hanging and
connecting frame
SP 5-09
29
Nut M12
SP 5-29
10
Elastic split pin
SP 5-10
30
Washer 12
SP 5-30
11
Vertical beam pin
SP 5-11
31
Press block of
plough
SP 5-31
12
Welded parts of right
vertical beam
SP 5-12
32
Cylinder pin 8
x 4
SP 5-32
13
Welded parts of left
vertical beam
SP 5-13
33
Assemble of
back impact
for plough
SP 5-33
14
Semi-rounded cylinder
pin
SP 5-14
34
Welded parts
of right grid
adjusting arm
SP 5-34
15
Split pin 2x2
SP 5-15
35
Elastic split
pin
SP 5-35
16
Press torsion spring
SP 5-16
36
Welded parts
of left grid
adjusting arm
SP 5-36
17
welded parts of
position adjusting for
side cultivation
SP 5-17
37
Movable parts
of grid
adjusting
SP 5-37
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 13 of 88
Rotation of the intercultivator must be stopped when it
is moving backward.
While operating the intercultivator, its rotation
must be stopped when it is moving backward.
Otherwise the operator might be caught by the rotating
claws, which will lead to serious injury or death.
Before starting the machine, the operator must be sure
that there is no potential danger in the surroundings.
Before starting the machine, the operator must
make sure that all the control levers are set at correct
positions and the surrounding is perfectly safe.
The operator must stop the machine before he tries to
clear the claws of mud and weeds.
If it is necessary to remove mud orweeds from the
machine during the operations, he must stop the
engine first. Otherwise serious injury or accidents
might occur.
The steering handles must not be used when the
machine is operating on a slope.
While operating on a slope, the operator must
extend the wheelbase to prevent the machine from
turning over. If he wants to take a turning, he must use
the manual handle instead of the steering handles.
Otherwise the machine might have the danger of
turning over and causing accidents or injury.
Before turning the manual handle to the opposite
direction, the left or right turning handle must be
switched over.
This machine is equipped with a turning
switchover device. When the operator wants to turnthe
manual handle to the reverse direction, he must use
the turning switchover between the handles, so that he
can take turnings in the same way as his usual habit.

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 14 of 88
Trailers bigger than the specified dimensions or
without a brake must never be used. If necessary, a
rear reflector, a backing mirror or a trumpet might be
installed.
The running speed of the machine must be limited
under 1 kmph. This limit must never be broken after the
belt pulley of the engineor the wheels (including paddy
field wheels) are changed.
The load in the trailer is limited to 500kgs. This limit
must not be broken either.
Before starting transportation, all the screws and nuts
must be tightened. Check the pressure of the tire
carefully and make sure that it is around 1.2kg/cm2.
Adjust the brake of the trailer and make sure that it
works effectively in both directions (right and left).
While the machine is running at high speeds, to bring
it to a halt, the brake of the trailer must be applied
slowly after the throttle is closed down.
When the machine is booked with a trailer and
running down a slope, if the brake of the trailer might
move toward the operator, which is very dangerous. At
a turning, the machine must be slowed down and the
manual handle must be used. At this time, use of the
steering handles is strictly forbidden.
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 75 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Welded parts of
spade
BM 2-01
12
Right hilling
supporting lever
BM 2-12
2
Counter sunk screw
M6 x 10
BM 2-02
13
Welded parts 0f
adjusting screw
BM 2-13
3
Nut M6
BM 2-03
14
Supporting lever
of left hilling
BM 2-14
4
Washer 6
BM 2-04
15
Welded parts of
left hilling plate
BM 2-15
5
Part of spade chest
BM 2-05
16
Extension plate
for left hilling plate
BM 2-16
6
Welded parts of
swing lever
BM 2-06
17
Counter sunk
screw M8 x 20
BM 2-17
7
Welded parts of right
hilling plate
BM 2-07
18
Nut M8
BM 2-18
8
Extension plate of
right hilling up
BM 2-08
19
Washer 8
BM 2-19
9
Pan-head screw M6
* 20
BM 2-09
20
Limit screw
BM 2-20
10
Washer 6
BM 2-10
21
Split pin 2 x 18
BM 2-21
11
Butterfly nut M6
BM 2-11
22
Welded parts of
adjusting screw
BM 2-22
5. Unit of Plough with Grid

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 74 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Assemble of turning
handle
G/B11-01
7
Washer 6-
Spring
G/B11-07
2
Screw M6 x 25
G/B11-02
8
Nut M6
G/B11-08
3
Nut M6
G/B11-03
9
Light fixed
press cover
G/B11-09
4
Fixed seat
G/B11-04
10
Reset torsion
spring
G/B11-10
5
Bolt M6 x 28
G/B11-05
11
Cable Turning
Right And Left
G/B11-11
6
Washer 6-Plain
G/B11-06
15. Unit of Fender
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Welded parts of left
fender
G/B15-01
4
Washer 8-
Spring
G/B15-04
2
Welded parts of right
fender
G/B15-02
5
Washer 8-
Plain
G/B15-05
3
Bolt M8 x 16
G/B15-03
2. Unit of Banking Machine
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 15 of 88
PARTS DESCRIPTION
Front Side:

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 16 of 88
Rear Side:
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 73 of 88
10. Unit of Switch for Left Turning Handle and Throttle
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Assemble of turning
handle
G/B10-01
8
Washer 6-Spring
G/B10-08
2
Screw M6 x 25
G/B10-02
9
Washer 6-Plain
G/B10-09
3
Nut M6
G/B10-03
10
Assemble of
switch for throttle
G/B10-10
4
Reset torsion spring
G/B10-04
11
Cable Throttle
G/B10-11
5
Fixed seat
G/B10-05
12
Saddle shape
elastic washer
G/B10-12
6
Assemble of Press
cover for left fixed
seat
G/B10-06
13
Press cover
G/B10-13
7
Bolt M6 x 20
G/B10-07
14
Screw M6 x 10
G/B10-14
11. Unit of Handle for Right Turning

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 72 of 88
9. Unit of Control Panel for Armrest Frame, Rotary Cultivation
Operation, Sub-Shift Operation and Main Clutch
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Assemble of armrest
frame
G/B9-01
9
Sheath of
armrest frame
G/B9-09
2
Sheath of handle
G/B9-02
10
Cable Clutch
G/B9-10
3
Welded parts of sub-
shift handle lever
G/B9-03
11
Cable Main
Gyro Tiller
G/B9-11
4
Sheath
G/B9-04
12
Bolt M12 x 124
G/B9-12
5
Stop Ring/Retainer
12
G/B9-05
13
Welded parts of
lock handle for
armrest
G/B9-13
6
Welded parts of
control handle lever
for rotary cultivation
G/B9-06
14
Washer 12-
Spring
G/B9-14
7
Unit of control panel
for operation
G/B9-07
15
Washer 12-
Plain
G/B9-15
8
Hexagram bolt M6 X
16
G/B9-08
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 17 of 88
Positions of Safety Reminders:

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 18 of 88
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 71 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
1
Tapping screw ST4
x 8-C-H
G/B8-01
18
Bolt M8 x 16
G/B8-18
2
Welded parts of limit
frame main shift
G/B8-02
19
Washer 8-Spring
G/B8-19
3
Seat of retainer
G/B8-03
20
Washer 8-Plain
G/B8-20
4
Indicating brand of
shift
G/B8-04
21
Fixed plate for
air filter
G/B8-21
5
Butter nut M5
G/B8-05
22
Welded parts of
fixed frame
G/B8-22
6
Washer 5-Spring
G/B8-06
23
Adjusting parts
(1set)0.8
G/B8-23
7
Adhesive parts of
limit blocks for rotary
cultivation
G/B8-07
23-1
Adjusting parts
(1set)0.5
G/B8-23-1
8
Hexagram bolt M8 x
12
G/B8-08
24
Butter Spring
G/B8-24
9
Bolt M10 x 135
G/B8-09
25
Turning sheath
G/B8-25
10
Washer 10-Spring
G/B8-10
26
Welded parts of
flexible shaft
fixed frame
G/B8-26
11
Tapping screw
ST5x9-C-H
G/B8-11
27
Bolt M8 x 70
G/B8-27
12
Washer 5-Spring
G/B8-12
28
Nut M8
G/B8-28
13
Fasten plate
G/B8-13
29
Washer 8-Spring
G/B8-29
14
Buffer sheath Q10 x
1
G/B8-14
30
Hexagram Bolt
M6 x 15
G/B8-30
15
Welded parts of
operation lever
G/B8-15
31
Washer 6-Spring
G/B8-31
16
Sheath of handle
G/B8-16
32
Nut M6
G/B8-32
17
Welded parts of
case
G/B8-17

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 70 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
116
Assemble of 19.05
agricultural
reinforced chain
G/B7-116
124
Assemble of
bone rubber oil
seal
G/B7-124
117
Passive gear
G/B7-117
125
Assemble of
ferrule
G/B7-125
8. Unit of Housing Returning Apparatus
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 19 of 88
FUNCTIONS OF DIFFERENT UNITS
Function of the starting unit:
Please get familiar with the names and functions of all the units and learn them by heart
1. Electric Starter Switch:
This switch is used at the time of starting
or stopping the engine.
When it is put to “Off”, the engine will be
stopped and when it is put to “On” the
engine will be running.
When it is put to “Start”, the battery will
start the motor so that the engine starts
running
2. Throttle Control Lever:
This lever is used when it is necessary to
adjust the speed of the engine. The throttle
must be put in the “High” position at the
time of starting the engine and back to the
“Low” position before shutting down the
engine. It might be set at any position as
required when the machine in operation.

KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 20 of 88
3. Control Lever for Manual Recoil-Type Starting:
When the engine is to be started, pull up
this manual lever, in a way as described in
the operation manual of the diesel engine
4. Pressure Reducing Control Lever
This lever can be used at the time of
starting when the battery is low and it is
difficult to start the engine.
Function of the Driving Unit
KisanKraft®
Agricultural Inter-Cultivator
KK- SRT- 910D / 910E
: www.kisankraft.com
: [e-mail]
: +91.80. 22178200
Page 69 of 88
Sl No
Part Name
Part No
Sl No
Part Name
Part No
98
Shift disk of sub-shift
G/B7-98
107
Spring of shift
fork of sub-
gearbox
G/B7-107
99
Active gear of low
shift
G/B7-99
108
Dust proof cover
G/B7-108
100
Washer
G/B7-100
109
Pin shaft B6 x 45
G/B7-109
Sl No
Part Name
Part No
Sl No
Part Name
Part No
110
Bearing 6304
G/B7-110
118
Core shaft
G/B7-118
111
Passive gear of
quick gear in
auxiliary shift
G/B7-111
119
Steel ball 8 II
G/B7-119
112
4th shaft
G/B7-112
120
Semi-shaft
G/B7-120
113
Passive gear of slow
gear in auxiliary shift
G/B7-113
121
Turning spring
G/B7-121
114
Active chain wheel
G/B7-114
122
Turning shift disk
G/B7-122
115
Washer
G/B7-115
123
Bearing 6207
G/B7-123