Knightsbridge SLULED Instruction Manual

1
101
INSTALLATION & MAINTENANCE MANUAL
SLULED
IP
44
230V
50Hz

2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
SLULED
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this luminaire should only be carried out by a qualified electrician or competent
person to the current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is Class I and requires an earth
• This product is IP44 rated
• Provide power to the point of installation. Suitable IP rated junction boxes should be used where
required
• Using the back plate as a template, mark the location of the fixing holes and drill the holes
ensuring not to infringe with any gas / water pipes or electrical cables (see Fig 1)
Fig 1
SLLED
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
SLLED
SAFETY
•Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•Please isolate mains prior to installation/maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•This product is Class I and requires an earth
•This product is IP44 rated
INSTALLATION
•Provide power to the point of installation. Suitable IP rated junction boxes should be used where required
•Using the back plate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas / water pipes or electrical cables (see Fig 1)
Fig 1
•Insert wall plugs and screws into the 2 drilled holes.
•Remove the 4 screws on the terminal cover plate and feed cable through the cable entry grommet
(see Fig 2)
Remove screws
Fig 2
Mark and drill fixing holes

3
Fig 2
Fig 3
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
Maximum shelf weight 2kg
• Insert wall plugs and screws into the 2 drilled holes.
• Remove the 4 screws on the terminal cover plate and feed cable through the cable entry grommet
(see Fig 2)
• Connect the Live (brown), Neutral (blue) and Earth (yellow and green) via the three-way terminal
connector (see Fig 3)
• Refit the terminal cover onto the fitting and fasten the 4 screws
• Carefully position fitting onto the screws in the wall
• Switch on the power supply and check for correct operation
• Please note the pull cord is for light operation only. Shaver and USB socket remain permanently live
The product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
WARNING
GENERAL
SLLED
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
SLLED
SAFETY
•Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•Please isolate mains prior to installation/maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•This product is Class I and requires an earth
•This product is IP44 rated
INSTALLATION
•Provide power to the point of installation. Suitable IP rated junction boxes should be used where required
•Using the back plate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas / water pipes or electrical cables (see Fig 1)
Fig 1
•Insert wall plugs and screws into the 2 drilled holes.
•Remove the 4 screws on the terminal cover plate and feed cable through the cable entry grommet
(see Fig 2)
Remove screws
Fig 2
Mark and drill fixing holes
•Connect the Live (brown), Neutral (blue) and Earth (yellow and green) via the three-way terminal connector (see
Fig 3)
Fig 3
•Re-fit the terminal cover onto the fitting and fasten the 4 screws
•Carefully position fitting onto the screws in the wall
•Switch on the power supply and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.
Irreparable damage will occur if this instruction is not followed.
Maximum shelf weight 2kg
GENERAL
The product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current
edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a replacement. ML
Accessories does not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
Neutral (blue)
N
E
L
Earth (yellow/green)
Live (brown)

4
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBJUN17_V1
This product has a warranty of 3 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period
it should be returned to the place of purchase for a replacement. ML Accessories does not accept
responsibility for any installation costs associated with the replacement product. Your statutory rights
are not affected. ML Accessories reserve the right to alter product specification without prior notice.
WARRANTY