KOBLE Apollo User manual

Issue 1 - 19/05/21
STOCK Ref: DOAPOW/DOAPOD

50kg.
Power Supply: AC adapter, 100-240V 50/60Hz
Service Environment: 0-40°C
Wireless Charging: 10W

Underside
Desk Top Qty 1
(120*60*1.8cm)
1
Power Adaptor Qty 1
(11.7*6cm)
6
Foot Qty 2
(58*7.4cm)
4
Flash Cable Qty 1
(50cm)
8
Leg Qty 2
(67*7.5cm)
2
(2.5*1.8cm)
7
Power Cable Qty 1
(310cm)
5
Cable for Wireless charging
device Qty 1
(40cm)
9
Controller Qty 1
(13*11.8cm)
3

ST4.2x19mm Qty 3
4x4 Qty 1 5x5 Qty 1
M6x12mm Qty 4 M6X16mm Qty 8

Assemble legs to top

4
STEP 1
4x4 Qty 1M6x12mm Qty 4
Insert
Screws
Pre-assembled
Important
Front
Back
Insert the hexagon Shape rod in the
end of the leg into the hexagon
shape hole in the motor housing.
Once inserted, rotate the

screws as shown.
Fit two more screws .

Assemble the controller
to top using
 .
5
Assemble feet to
legs  .
STEP 2
4x4 Qty 1
M6X16mm Qty 8
Front
Back
STEP 3
ST4.2x19mm Qty 3 5x5 Qty 1
Front
Back

a. Conne
to power adaptor .
b. Conne
to the DC port on controller
.
c. Connect power cable
to power adaptor .
d. Finally locate the adaptor
into the bracket on
the underside of the top.
STEP 4
6
Connect wireless charging
cable in between the
wireless charging module
on the underside of the
desk top and the port
next to HS on the
controller .
STEP 5
Finally route cables through
7
7
7
7
7
7
7
7
Organize the cables
a. b. c.
Fixed
Connect the motor
cable to the M1 port on
controller .
STEP 6
6
8
6
8
a.
5
6
c.b.
8
Motor cable
3
3
6
3
5
6
8b
d.
underside
3
9
9
a.
b.
9
Remove self
adhesive backing

7
With help, carefully
turn the desk over into
connect to a power
source.
STEP 7

8
LED Screen
UP/DOWN Keys
Memory Keys
Control Panel
Height Adjustment / Controls
when the desktop reaches its highest point.
desktop reaches its lowest point.
Short press the key orkey, to make small adjustments to the height.
encountered whilst the top is beingadjusted, it will stop and rebound.
Press the chosen memory key (1, 2, 3or 4) and hold for 3seconds.
Thedesk top will adjust to the pre-set height.
Standing:
Programme Preset Height (Standing/Seated)
Press memory keys and hold for 3 seconds.
to the pre-set height.
Seated:

release down keys, the reset is over and the table can be used normally.
b.When itdoesn't work and the LED shows "E01" or "E02", please retry 18 mins later.
the power for at least 10 seconds. Reconnect the power and press keys to start and reset process when itshows
the “RST”.
d.If all these above process are ineient, plz contact our customer service.
9
Wireless Charginglogo
Wireless Charging Function
Troubleshooting
below.
Fault phenomenon Method Fault phenomenon Method
No response whilelongpressing
a power supply
1.Check if all the cables be connected well
2.Contact yoursupplierordealer
No response whilepressingup
connected with a power supply
1.Check if all the cables be connected well
2.Contact yoursupplierordealer
Risingin alow speed
1.Check if overloaded, max loading: 50kg;
2.Contact yoursupplierordealer
The motor not move as instructed 1. Contact yoursupplierordealer
2.Contact yoursupplierordealer
Go down butnot go up
Downward sliding
2.Contact yoursupplierordealer
1.Check if overloaded, max loading: 50kg;
Overwork
（Duty cycle:Max 2min on/18min OFF）
2.Contact yoursupplierordealer
1.Check if overloaded, max loading: 50kg;
with power;
2.Contact yoursupplierordealer;
1. Press "M"and "3" together for 3 seconds ormore,
Not enough up&down height
2.Contact yoursupplierordealer

10
Important Information
1. Power supply: AC100V-240V, 50/60Hz
2. Service Environment: 0-40°C
3. Unplug the power plugbefore cleaning, wipe the dust on surface with damp cloth when cleaning. Be careful
not to let water drops into the internal parts, orloose the connector.
4. Check carefully to ensure correct and complete assemblybefore using.
6. Don’t allow children to play near the desk as their behavior is unpredictable. The manufacturer is not responsible
7. Theslight noise caused by the internal mechanismorbrake system of the structure, will nothave any eect on the
useof the equipment.
8. Do notuse corrosive orabrasive materials are near the equipment. Please ensure that the cleanerused will not
pollute the environment.
9. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
concerninguseof the appliance in a safe way and understand the hazards involved. Children should notplay with the
appliance.
11. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent orasimilarly qua
person in order to avoid a hazard.
chokinghazard to children.
13. We recommend you keep the original package of the equipment if necessary in case of the future use in

This markingindicates that this product should notbe disposed with otherhousehold
wastes. To prevent possible harm to the environment orhuman health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
retailer where the product was purchased. They can take this product for environmental
safe recycling.
11
Purchased from kobledesigns.com
In the unlikely event that you need to return the unit because it is faulty, please follow the replacements


Email - [email protected]
Tel: + 44 (0)1799 513 466

Purchased from other retailer
If you purchased your product from one of our retail partners, please refer back to the retailer directly,
for any customer services related issues, refunds or returns requests.
