KOCOM KAL-S302 User manual

KAL/KEL-A Series S0531
Audio LobbyphoneManual
[ KAL-S302 / KAL-S303 / KAL-S304 / KAL-T306 / KAL-T308 ]
[ Extension : KEL-A308 / KEL-AT316 ]
SINCE
1976
KOREA COMMUNICATIONS CO.,LTD
http://www.kocom.com
E-mail : [email protected]
This manual is based on the date as shown in the right and specifications are subject to
change without notice for quality improvement
Warranty
Warranty Card
1) This product is produced under strict quality control and inspection procedures.
2) If this product breaks down during proper use as a result of product defect, KOCOM
will repair it within one year from date of purchase free of charge.
3) The following cases will be subject to charge, even during warranty period:
a. Breakdown during transport, or through careless treatment, by consumer.
b. Breakdown cause by unauthorized repair, or system modification.
c. Breakdown caused by natural disaster or power disorder.
1. Name of the product.
2. Model number of the product.
3. The area of problem.
4. Phone number and address at which you can be contacted.
PRODUCT
MODEL
DATE PURCHASED
WARRANTY PERIOD
AGENCY ADDRESS
KOCOM Warranties the original purchaser of this product as follows.
To receive after service, have the following ready before you
contact our branches.
www.kocom.com
■Slim & Stylish Design Surface mount type Audio Entrance Panel
■Call, Communication, and Door Open with Interphone (KIP-304)
■Clear & Loud Voice & convenient Voice Volume Control
■Max. 120 Household, 7 extension connections available
■Easy Installation (3+n)
■Name Plate backlight (LED lamp)
■Safe Door Open function only when the communication is made
■Two door release type (NO & NC) connection available
■Security Alarm Function [Security Sensor (※not included) is needed]
Audio Lobbyphone
▶ KAL-T308 ▶ KEL-AT316
Extension Unit(option)
■2pcs of KIP-304 is available per 1 household

4
Cautions for safety
6
Installation
6
Name of Each Part
7
Components
7
Product Specifications
8
8
Operation Explanation
Button Information
Wiring Connection
■
■
■
■
■
■
■
■
9
Contents

For safe use, please stick to the following cautions.
·Please, save this manual after reading these instructions carefully. ·Read and understand all instructions to set up rightly.
·This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases.
·If you need assistance with the set-up or operation, please contact with A/S center.
To help our customers to understand this manual, to prevent any personal injury or property damage, some marks are used in the manual.
The marks and the drawing signs are below. Please, understand the marks before reading the manual.
Cautions for set-up
The important marks in the manual.
The meaning of the drawing signs.
Sign to show what not to doMishandling the device with ignoring this sign may result in serious injury or death.
Mishandling the device with ignoring this sign may result physical injury or material damage.
Sign to tell you that you should follow the instructions.Sing to tell you that you need more attention including high voltages, electric shock, danger, warning)
Sign to tell you that you can't disassemble this unit.Sign to tell you that you must unplug the unit.
·The law limits distributing the power lines to an authorized person from government. The work from an unaurhtorized person cause fire or electric shock.
·Place this unit securely on a stable surface. Serious damafe and/or injury may result if the unit falls.
·Do not set up this unit near the leaking place because it may expose you to dangerous voltages or other risks.
·Even if your product is water proof, do not install it slanted place of water leakage, which can a short circuit.
·The work of distributing wires needs skills and experiences. So please, for assistance, contact your dealer or call service center.
·The communication lines should be built in being distant from the power source. This may result in the risk of fire, electric shock and communication disorder.
·Setting the communication lines in a high humid place such as outside without any protection from rain causes the communication disorder.
·Keep the hook at the wall-mounted device safe. The hook may cause the physical injury.
·Think about the thickness and quality of wall material. The unqualified material may make the device fall.
Warnings for Usage
·Do not install this unit near the water and dust, for example, in a bathroom or near the washing machine. It caused fire and electric shock.
·Do not install this unit near the fire, for example, near kitchen sink, heater or the like.
·Do not install near the noxious gar such as Hydrogen Sulfide, metal power and the like.
·Do not install near the water and chemicals.
·Do not give any damage, break and modify the plug. Overloading, heating, pulling causes the damage.
·Do not place the plug near the heater. The damaged code causes fire and electric shock. Do not pull the power code when unplugging.
·The damaged code causes fire and eclectic shock. Must pull with plug. Do not touch with wet hands. It causes the electric shock.
·Do not use any other voltage, except the marked regular voltage.
·Do not use the power terminal at the units to other electric device except the designed device.
·Do not install the units at the leaking place if it doesn’t have any waterproof mark. Do not install the unit when the power is on.
·Install the circuit breaker after checking the safety such as electric shock and leakage. Turn off the power before you install or A/S
·Check the suitability of the lines for installing when you use the exiting lines.
·Do the wiring work by using the designed material.
·Connect the electric wire with the designed ways and ground.
·Do not connect with any other devices except the designed devices to compose the system.
·Unplug electric wire and communication lines from the units before moving to another place.
·Unplug this device when you want to check the inside. If there is no plug, please, turn off the circuit breaker.
·Unplug this device when you try to move it to another place. If the electric line is connected inside of the unit, please contact your dealer or service center.
·Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning
Cautions for Repairs and Maintenance
·Keep the inside of the device clean. Having the dust inside without any cleaning for a long time causes the fire. If necessary, contact your dealer or service center to get cleaning service.
·Set the device of the wall-mounted type not to fall. Falling from an earthquake causes personal injury.
·Change the damaged electric code.
·Unplug this unit from plug socket and refer servicing to an authorized service center when the following conditions occur:
·If liquid has been spilled into the unit. 쪾·If the unit does not work normally by following the operating instructions.
·If the unit exhibits a distinct change in performance. 쪾·If the unit has been dropped or physically damaged.
·Do not disassemble this unit at will as this device is composed by precision parts. 쪾·Install the unit by following the set-up instructions of Kocom.
·Do not touch or insert any foreign substances, for example, sticker, magnetic, opener and the like
·Make U-type at the end of wires as the rain can effect on the system by following the wires during the rainy season.
Cautions for Use
Cautions for Abnormality
Safety Instructions, Warnings and Cautions of Each System
·This unit is not designed for security purpose. 쪾·Do not handle the unit with the wet hands.
·Do not place a pot with water or a small metal material on the Units.
·Do not cover the ventilating opening or put any metal material in the units. 쪾
·During thunderstorms, avoid using this unit. 쪾There may be a remote risk of an electric shock from lighting.
·Do not modify the unit. ·Open the main gate after checking ID if the image and sound system do not work. Call A/S
·Do not disassemble the back and cabinet cover.
·Separate the AC/DC lines with the hook of the wall-mounted type when installing. 쪾·Connect the lines after peeling the wires properly
·Do not distribute signal line with AC line. 쪾·Use the designed driver to connect the lines to terminal
·Do not clean the LCD with the damp cloth for cleaning. Use the only dry and soft cloth. 쪾·Do not install the main gate monitor at the leaking place.
Videophone
·This product is designed as a home videophone and cannot use continuously like monitor camera.
·If there is temperature difference between inner part of camera and surrounding, dew condensation occurs on camera lens and may disturb image.
If dew condensation is removed from camera lens, image quality recovers.
·White LED light examination range is narrower than camera shot range at night, so there is less amount of light at night than day.
So it is difficult to see the face in low illumination condition due to noise increase on screen, but it is not from defect.
·Monitor screen (liquid crystal panel) is not in defect when some pixels always light or black out.
·Please install monitor and camera over 5cm away. Also, avoid installing at a place with too much noise, because too much noise around camera causes phone call inferiority.
·Do not place an object within 20cm in front of monitor. It causes phone call inferiority, especially because microphone is installed at the top of monitor.
·If strong light such as sunlight flows into camera module, screen saturation (or strange mark) and image shaking might occur.
·This is not a defect, so please do not install camera where a direct ray of light do not flow if possible.
Things You Need to Know
·In some cases there is occurrence of product destruction, malfunction, noise mixing and picture quality deterioration due to mixing of other tool’s induced
voltage or thunder with communication wiring of monitor/camera, monitor/extended monitor.
Do not wire with power line such as outdoor wiring or AC power, or phones and other tools.
·You cannot use it if you incorrectly wire the AC voltage between monitor/camera, monitor/extended monitor. Call the store or agency where you purchased
this product and consult to solve the problem.
Beware that unfixable damage might be caused due to authorizing AC voltage on communication wiring of monitor/camera, monitor/extended monitor.
·Do not ever disjoint this product. It may cause electrocution accident when touching high-voltage circuit inside this product.
·Outside power authorizing this product must be confirmed of product description and use rated voltage. Beware that if higher voltage is authorized, unfixable
damage might be caused due to product destruction.
·Power must be connected to domestic voltage (product rated voltage) consent or interior wiring.
If connected to other motive power or inverter-type power, product destruction, noise mixing, and picture distortion may occur.
·Do not drop this product. Glass is used for monitor and might break, or cause other circuit inferiority.
In such case, immediately turn down the power switch, and call to consult agency or store in which this product was purchased.
·If installed near transmission antenna such as broadcasting station, electric wave may mix and cause picture distortion or voice mixing.
·Avoid installing near tools with strong electromagnetic waves such as microwaves and cell phones, or it may cause picture distortion.
·Do not install monitor in following places.
① Above or around water heater, rice-cooker, heater ② Place exposed to direct rays of the sun ③ Place with temperature below 0'C such as cold store
④ Place with high humidity such as bathroom, washroom, heated room
⑤ Place with a lot of gas, dust, smoke ⑥ Dangerous place with sprays of water or chemicals
·Do not wipe with insecticide, drugs or chemicals such as thinner and alcohol, or it may damage
the surface of this product.
·Beware of occurrence of image quality deterioration or malfunction from cause of humidity due to
penetration of chemicals or water into camera’s urea resins.
·As in the picture, it prevents temperature difference of camera (outside) and monitor (inside), and
removes dew condensation caused by humidity of camera window.
·Camera must be installed when wall cement is completely dry.
·When product is installed in winter below -5'C, wait for approximately 2 hours to connect. Dew formation
in monitor and camera due to temperature difference inside and outside may cause product defect.
·Avoid installing monitor and camera in place directly exposed to heat or where gas noxiousness is
highly occurring.
Cautions
Stop up P.V.C pipe using
adiabatic substances, to
prevent air circulation
Tubing BoxMonitor
Pipe
Camera
(Outdoor, Door)
54

Installation Components
1) Install dummy on the wall using dummy screws.
2) Connect wires to lobbyphone back terminal referring to product connection diagram.
3) Hang Main body on dummy, and fix it on dummy using wrench screws.
Screw
Main body
Audio
lobbyphone
Audio lobbyphone Dummy
Extension
(option)
Dummy
Wrench
WallWall
76
Sun visor (Option)
Screws
Wrench screw 2EA
Screws
Dummy screw 4EA
"L" Wrench
8 pin connector between
audio lobbyphone & interphone
1. Black : House NO.8
2. Brown : House NO.7
3. Red : House NO.6
4. Orange : House NO.5
5. Yellow : House NO.4
6. Green : House NO.3
7. Blue : House NO.2
8. Purple : House NO.1
1
2
3
4
1
2
1
2
3
4
5
6
7
8
1
2
3
4 pin connector between
audio lobbyphone & interphone
1. Black : AUDIO-MIC
2. Brown : AUDIO-SP
3. Red : GND
4. N.C (Not Connection)
Power input connector between
audio lobbyphone & adaptor
1. Black : GND
2. Red : +12V
3pin connector between
audio lobbyphone & door opener
1. Yellow : COM
2. Brown : N.C
3. Black : N.O
1
3
1
2
2pin connector between
audio lobbyphone & sensor
1. Black : COM
2. Red : N.C
1. Black
2. Brown
3. Red
Extension connector between
audio lobbyphone & extension unit
Terminal for extension
House connection terminals
Adjust the audio switch-lobbyphone
Adjust the audio switch-house
Power input terminal
Security sensor switch
Terminal for extension
8
9
10
11
12
13
14
9
Name of Each Part
C-Mic
Speaker
Name indicator-shows house information
Call button
Terminal for door opener
Terminal for interphone
Terminal for security sensor
1
2
3
4
5
6
7
5
6
7
8
10
11
13
12
14
1
2
3
4
FRONT
AUDIO LOBBYPHONE EXTENSION (OPTION)
SIDE BACK
Product Specifications
DC+12V±1V(Stand by : 1W, Operating : 8W)
Hands free method (two way)
125(W) X 240(H) X 30(D)mm
-10°C ~ 50°C
Input power
Communication method
Dimensions
Guaranteed operating
KAL series / KEL seriesSpecifications
※Compatible products : INTER PHONE : KIP-304

: Audio lobbyphone →Monitor audio volume
Using a screwdriver, increase(+) or decrease(-) the
volume from the Common gate camera to the house
: Interphone →Audio lobbyphone audio volume
Using a screwdriver, increase(+) or decrease(-) the
volume from the house to the Common gate camera
Button Information
■ AUDIO LOBBYPHONE
KAL-S302 KAL-T308KAL-T306KAL-S304KAL-S303
2 House 8 House6 House4 House3 House
1
3
5
7
2
4
6
8
1
3
5
2
4
6
2
4
6
8
■ EXTENSION UNIT
KEL-A308 KEL-AT316
8 House 16 House
2
4
6
2
4
Wiring ConnectionOperation Explanation
98
AUDIO LOBBYPHONE CONNECTION
AUDIO
LOBBYPHONE
AUDIO LOBBYPHONEEXTENSION UNIT
EXTENSION CONNECTION Terminal for door opener
(Extra adaptor is needed)
※
Door opener is output in N.O / N.C and is
used in connection in compliance with door
release specification.
Door
relese
Door
relese
Audio lobbyphone to household
Cable requirement※
※2 Pin terminal output : Installing status N.C mode / Disarm status N.O mode
up to 100m : CAT5 Cable (2group 4wire)
Black :
Normal
open
Brown :
Normal
close
Yellow :
Common
Yellow :
Common
DC
adaptor
Normal open Normal close
DC
adaptor
■Adjust audio
DOOR
RELEASE
DC+12V
300mA
HOUSE
NO.1
HOUSE
NO.2-1
HOUSE NO.1~8
DC+12V 300mA
Non-polarity
Non-polarity
polarity
security
sensor
DC
adaptor NORMAL
OPEN
COMMON
NORMAL
CLOSE
DC+12V
1.5A
GND
DC 12V
adaptor
polarity
4 5 6 7 81 2 3
4 5 6 7 81 2 3
4 5 6 7 81 2 3
HOUSE NO.9~16
polarity
4 5 6 7 81 2 3
HOUSE NO.1~8
polarity
HOUSE
NO.17~24
polarity
32
1
EXTENSION UNIT cannot be used without Audio lobbyphone※
1. When the visitor presses the call button for certain house on the audio lobbyphone,
the certain house interphone gets call signal.
2. In case of hanging up the hand-set or pressing talk button, the conversation is available.
3. When finishing talk, put the hand-set onto the HOOK BAR or press talk button once again.
■Communication with house interphone
1. Detecting security sensor and security mode
2. In case of security sensor is separating from wall, status is changing to N.C →N.O
3. Need to connecting extra security sensor (optional)
■Security Function
1. During conversation with household interphone, if the door open button on the interphone is pressed,
the common gate is released, in case the door opener is equiped.
2. In order to connect the door opener to the 3 wire connection (polarity) on the
audio lobbyphone, you should use KIP-304 interphone only.
Cabling is 3 wires in common & 1 separate wire
for each house.
For 1 separate wire connection for each house
using ‘8 pin connecter’, please refer to the
numbers shown next to the buttons & detailed
wiring diagram at page 10 and 11.
※
■Audio lobbyphone from house interphone
HOUSE
NO.2-2 (Option)
32
1
32
1
Option

Doble side Buttons Wiring Connection (Max. 120 Houses, 7 extension)
1110
4 5 6 7 81 2 3
HOUSE NO.1~8 polarity
4 5 6 7 81 2 3
HOUSE NO.9~16 polarity
4 5 6 7 81 2 3
4 5 6 7 81 2 3
HOUSE NO.25~32 polarity
4 5 6 7 81 2 3
HOUSE NO.33~40 polarity HOUSE NO.17~24 polarity
H
O
U
S
E
N
O
2
H
O
U
S
E
N
O
1
H
O
U
S
E
N
O
40
H
O
U
S
E
N
O
3
H
O
U
S
E
N
O
4
H
O
U
S
E
N
O
5
H
O
U
S
E
N
O
6
H
O
U
S
E
N
O
7
H
O
U
S
E
N
O
8
H
O
U
S
E
N
O
9
H
O
U
S
E
N
O
10
H
O
U
S
E
N
O
11
H
O
U
S
E
N
O
12
H
O
U
S
E
N
O
13
H
O
U
S
E
N
O
14
H
O
U
S
E
N
O
15
H
O
U
S
E
N
O
16
H
O
U
S
E
N
O
17
H
O
U
S
E
N
O
18
H
O
U
S
E
N
O
19
H
O
U
S
E
N
O
20
H
O
U
S
E
N
O
21
H
O
U
S
E
N
O
22
H
O
U
S
E
N
O
23
H
O
U
S
E
N
O
24
H
O
U
S
E
N
O
25
H
O
U
S
E
N
O
26
H
O
U
S
E
N
O
27
H
O
U
S
E
N
O
28
H
O
U
S
E
N
O
29
H
O
U
S
E
N
O
30
H
O
U
S
E
N
O
31
H
O
U
S
E
N
O
32
H
O
U
S
E
N
O
33
H
O
U
S
E
N
O
34
H
O
U
S
E
N
O
35
H
O
U
S
E
N
O
36
H
O
U
S
E
N
O
37
H
O
U
S
E
N
O
38
H
O
U
S
E
N
O
39
HOUSE NO.1~8 HOUSE NO.33~40 HOUSE NO.9~16 HOUSE NO.17~24HOUSE NO.25~32
4 5 6 7 81
1
2
3
1
2
3
2 3
HOUSE NO.1~4 polarity
4 5 6 7 81 2 3
HOUSE NO.5~8 polarity
4 5 6 7 81 2 3
4 5 6 7 81 2 3
HOUSE NO.13~16 polarity
4 5 6 7 81 2 3
HOUSE NO.17~20 polarity HOUSE NO.9~12 polarity
H
O
U
S
E
N
O
1
H
O
U
S
E
N
O
20
H
O
U
S
E
N
O
2
H
O
U
S
E
N
O
3
H
O
U
S
E
N
O
4
H
O
U
S
E
N
O
5
H
O
U
S
E
N
O
6
H
O
U
S
E
N
O
7
H
O
U
S
E
N
O
8
H
O
U
S
E
N
O
9
H
O
U
S
E
N
O
10
H
O
U
S
E
N
O
11
H
O
U
S
E
N
O
12
H
O
U
S
E
N
O
13
H
O
U
S
E
N
O
14
H
O
U
S
E
N
O
15
H
O
U
S
E
N
O
16
H
O
U
S
E
N
O
17
H
O
U
S
E
N
O
18
H
O
U
S
E
N
O
19
HOUSE NO.1~4 HOUSE NO.17~20 HOUSE NO.5~8 HOUSE NO.9~12HOUSE NO.13~16
HOUSE NO.9~24HOUSE NO.25~40
Audiolobbyphone KAL-T308Extension unit KEL-AT316
Extension unit KEL-AT316Extension unit KEL-AT316
Extension unit KEL-AT316
1
2 1
3
4
5
6
7
8
2
3
4
5
6
7
8
8 7 654321
87654321
8 7 654321
Audiolobbyphone KAL-S304Extension unit KEL-A308Extension unit KEL-A308
2
2
4
6
8
4
6
8
86
4
2
86
4
2
86
4
2
HOUSE NO.1~4HOUSE NO.5~12
Audiolobbyphone KAL-S304Extension unit KEL-A308
2
4
6
8
HOUSE NO.13~20
Extension unit KEL-A308
HOUSE NO.1~8
Audiolobbyphone KAL-T308
1
3
5
7
2
4
6
8
Connection between
Audio lobbyphone and
Extension unit &
Extension unit and
Extension unit
Connection between
Audio lobbyphone and
Extension unit &
Extension unit and
Extension unit
Single side Buttons Wiring Connection (Max. 60 Houses, 7 extension)