Kodak Scanmate i1120 User manual

CLEANING THE CALIBRATION AREA
1. Remove dust and debris from this area by using a Stati-
cide wipe, a small brush or scanner cleaning swab. Be
careful not to scratch the glass or bend the white
tabs on the calibration guide.
2. Wipe the calibration guide with a Staticide wipe.
IMPORTANT:Staticide wipes and cleaning swabs contain
isopropanol which can cause eye irritation
and dry skin. Wash your hands with soap and
water after performing maintenance
procedures. Refer to the User’s Guide for
MSDS acquisition.
3. Wipe the front and rear calibration guides again with an
almost-dry Staticide wipe to remove any streaks.
REPLACING THE FEED ROLLER ASSEMBLY
1. Remove the input tray by pulling it forward and lifting it
out of position. Set it aside.
2. Rotate the orange tab upward to release the feed roller
assembly.
3. Lift the feed roller assembly up and out of the
scanner.
4. Install the new feed roller assembly by aligning the shaft
end of the assembly in position.
5. With the orange tab in the upward position, snap the
feed roller assembly in place.
6. Rotate the orange tab down. If the tab is not in the down
position, you will not be able to reinstall the input tray.
7. Reinstall the input tray by locating and aligning the four
tabs on the input tray with the slots on the scanner.
8. When tabs and slots are in place, roll the input tray
toward the back of the scanner until it snaps into place.
SUPPLIES*
* Items are subject to change.
EASTMAN KODAK COMPANY
343 State Street
Rochester, New York 14650 USA
© Kodak, 2007
TM: Kodak, ScanMate and Digital Science
A-61603/Part No. 9E8503 January 2008
ScanMate i1120 Scanners
Quick Tips
www.kodak.com
Kodak Field Service:
1-800-356-3253
Kodak Technical Assistance:
1-800-822-1414
Kodak Professional Services:
1-800-525-6325
CAT No. Description
894 6097 Kodak ScanMate i1120 Pre-Separation
Pad
122 6034 Kodak ScanMate i1120 Feed Roller
Assembly
824 5862 Kodak ScanMate i1120 Scanner
Cleaning Swabs
853 5981 Kodak Digital Science Roller Cleaning
Pads (qty 24)
169 0783 Kodak Digital Science Transport
Cleaning Sheets (qty 50)
896 5519 Staticide Wipes for Kodak Scanners
(qty 144)

SCANNER DISPLAY AND FRONT PANEL
Function window — displays 1-9. These numbers
correspond to 9 predefined scanning functions. This
window may also display error codes. See the User’s Guide
for more information.
Arrow button — allows you to select or scroll through
predefined functions 1 through 9.
Start button — launches the selected application that is
associated with the displayed number in the Function
window.
NOTE: The Start button, Scroll button and Function window
are used with the smart touch functionality.
Indicator light — illuminates or flashes indicating scanner
status.
•Steady green: ready to scan.
•Flashing green: scanner lamps are warming up,
preparing to scan.
•Flashing red: error indication such as, document jam,
in conjunction with the Function window displaying an
“E”.
POWER SWITCH AND CONNECTORS
Power switch — turns the scanner on and off.
Power port — connects the power cord to the scanner.
USB port — connects the scanner to the PC.
CLEANING AND MAINTENANCE
For detailed cleaning and replacement procedures, see
Chapter 5, Maintenance in the User’s Guide.
OPENING THE SCANNER COVER
1. Open the scanner cover by pressing the release lever.
2. Close the scanner cover when finished cleaning
internal components or replacing parts.
CLEANING OR REPLACING THE PRE-
SEPARATION PAD
You may need to replace the pre-separation pad if it is worn
or multi-feeding continues to occur after cleaning.
1. Squeeze the plastic clamps that hold the pre-separation
pad in place and lift it out of position.
2. Wipe the pre-separation pad from top to bottom or if the
pre-separation pad shows signs of wear, replace it.
3. Reinsert the pre-separation pad into position, aligning it
into the slots, and pushing it in until it snaps in place.
CLEANING THE ROLLERS
The rollers and calibration area should be cleaned routinely
for optimum performance. Some paper types and operating
environments require cleaning more often then specified in
the User’s Guide. Whenever paper feeding and image
quality are less than desirable, follow these steps.
1. With a roller cleaning pad, wipe the feed roller from side
to side. Rotate the rollers to clean the entire surface.
2. Wipe the NFR rollers from side to side. Rotate the NFR
rollers to clean the entire surface. For easier cleaning,
order Kodak ScanMate i1120 Scanner Cleaning
Swabs.
IMPORTANT: When cleaning this area, be careful not to
bend the white tabs; bending the tabs may
cause paper feeding problems.
3. Dry the rollers with a lint-free cloth.
1-4 Scanner failure
5 Internal test
6 Light check failure
7 Command failure
8 Document jam
9, 0 Internal test
15 Cover is open
Function window
Arrow button
Start button
Indicator light
Power switch USB portPower port