Kogan KAMN24F75LB User manual

User Guide
(KAMN24F75LB)
24" Full HD IPS 75Hz Frameless Monitor
(1920 x 1080)

2
Contents
Contents ..................................................................................................... 02
Components ............................................................................................... 03
Overview ..................................................................................................... 04
Stand Assembly .......................................................................................... 05
............................................................................................ 07Wall Mounting
Connectivity ............................................................................................... 08
Basic Operation ........................................................................................... 10
Indicator Light ............................................................................................. 10
Operation ...................................................................................................... 11
ECO Modes and Gameplus Switching ....................................................... 13
Specifications .............................................................................................. 14
Notes ............................................................................................................ 15
Safety and warnings
Read all instructions before using the appliance and retain for reference.
1. Unplug the monitor before cleaning it with a slightly damp, clean cloth.
2. Wiping the screen once it has been turned off with a dry microfibre cloth is
recommended.
3. Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
4. This monitor is designed with ventilation holes on the back of the casing. Do
not cover or block them.
5. Avoid placing the monitor near heaters, stoves, fireplaces or other sources of
heat, as well as in rooms lacking in adequate ventilation.
6. Do not insert any objects or spray any liquids into the vents.
7. Do not position the monitor in unsafe locations. If the monitor falls, it may be
damaged and may injure nearby people.
8. Unplug the monitor if it is not going to be used for an extended period.
9. Do not place heavy objects on the monitor, its power cord or any connected
cables.
10. Do not open the back panel of the monitor, as it contains a high-voltage
current even when not plugged in.

KOGAN
24” FHD FreeSync Monitor
QUICK START GUIDE
(KAMN24F75LB)
12mm
Components
A
B C
A Monitor F 10mm VESA connectors ( x 2 )
B Stand Stem G Power Adapter
C Stand Base H HDMI Cable
D PM4*12mm Screws ( x 2 ) I User Guide
E 26mm VESA connectors ( x 2 )
D
H
G
E
I
3
26mm
10mm
F

Monitor Controls
7 Power Connector: Insert the power cable to supply power to the monitor.
8
VGA Connector: Insert one end of the VGA cable into the computer’s VGA output
and connect the other end to the monitor’s VGA port.
9
HDMI Connector: Insert one end of the HDMI cable into the computer’s HDMI
outpu t and connect the other end to the monitor’s HDMI port.
2 3 4 5 6 1
1 M Menu Button: Press to display the OSD menu or enter sub-menus.
2 Down Button: Press to move down in the menus.
3 Up Button: Press to move up in the menus.
4 E Exit Button:
Press to exit.
5 Power Button: Press to turn the monitor on/off.
6 LED Indicator: Changes colors to indicate status.
Monitor Ports
7 8 9
10
Audio Output: Insert one end of the Audio cable into the computer’s Audio output
to receive the Audio signals from your monitor.
Overview
4

Keep the foam underneath the monitor before attaching the stand.
1. Open the package, take out the product with foam still attached, and gently
place it on a desktop or table.
Monitor
Stand Base
Foam
Stand Stem
2. Turn the bracket on a slight angle and align it with the circular slot of the base. Insert
the bracket into the base, and then rotate clockwise to clamp the bracket into the
base to complete the installation of the base.
3. Align the stand with the slot at the rear of the monitor, and insert the stand into the
monitor. To prevent damage during assembly, ensure the monitor is still in the original
foam.
2.1
Align stand with
the base slot.
2.2
Keep the bracket
and the base close,
rotate the bracket
clockwise.
2.3
Make the bracket
click into the base.
2.4
Insert screws to base
and tighten.
2.5
Complete stand
and base assembly.
Place Stand to the slot of monitor, and push up.
Stand Assembly
5

To avoid damage, do not touch the screen when moving the monitor.
4. Complete overall assembly.
Note 1: To prevent pinching, please do not place your hand within the gap between
the stand and the monitor.
Note 2: To prevent falling, please avoid holding monitor by the base or inverting the
monitor.
Note: Do not invert the machine to
prevent falling.
6

7
3. Your monitor is now ready to be attached to a wall-mounting bracket. To avoid
damage, please do not pinch the screen during bracket installation.
Lock the two 26mm VESA connectors in the upper two holes on the rear of the
monitor, and the two 10mm connectors in the lower two holes.
2.
Mont
(Notincluded)
VESA Connector
Monitor
1. Take out 4 pieces VESA connector from accessory bag.
Wall Mounting

VGA
In order for the monitor to receive VGA signals from the computer, use a VGA cable
to connect the monitor to the computer.
VGA OUTPUT
VGA Cable (Not included)
Earphones
Plug in your earphones to receive audio signals from your monitor. If your earphones are
connected to the monitor and audio devices are connected to your computer at the same time,
the audio devices will not produce sound. Earphones and other audio devices not included.
Earphones (Not included)
8
Power Cable
Connect the included power cable to the power connector, and then plug the other end
into an wall outlet.
Power Cable
Connectivity

HDMI
In order for the monitor to receive HDMI signals from the computer, use the HDMI cable
the monitor to the computer.
to connect
HDMI OUTPUT
PC
HDMI Cable (Included)
9

Insert one end of the HDMI cable into your PC’s graphics card. A VGA cable may also
be used. A VGA cables is not included.
1. Connect the other end of the cable to the corresponding connector on your monitor.
VGA Connector
HDMI Connector
2. Connect the power cable to your monitor then connect the other end to your power
source. It is recommended that you use a surge protector with adequate voltage if a wall
outlet cannot be reached directly.
3. Locate the power button on the monitor and press it to turn the monitor on.
Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light
indicates no video source has been detected. Red light indicates that no horizontal or vertical
signal has been detected or voltage is low. Please ensure your computer is on and all video
cables are fully inserted and/or connected.
Indicator Light
Indicator Light
Basic Operation
10

The On-Screen Display (OSD) Menu may be used to adjust your monitor’s settings
and appears on screen aer turning on the monitor and pressing the M button.
When using the monitor for the fi rst time, settings will automatically adjust to
optimal settings according to your computer’s configuration and parts etc.
1. Press any one of the buttons ( M, , , E, ) to activate the navigation window.
eco
2. Press M to enter the OSD menu.
BRIGHTNESS
BRIGHTNESS
CONTRAST
ECO
DCR
STANDARD
OFF
3. Press or to browse functions.
• Highlight the desired function, then press M to enter the sub-menu.
• Press or to browse sub-menus, then press M to highlight the desired
function.
• Press or to highlight an option, then press M to confirm the settings and exit
the current screen.
4. Press E to exit the current screen.
Operation
11

List of Functions
Main Menu Sub-Menu Options Description
BRIGHTNESS Brightness 0~100 Adjust display brightness
Contrast 0~100 Adjust display contrast
ECO Standard, Game,
RTS, FPS, Movie,
Text
Set visual mode
DCR On Turn on DCR function
Off Turn off DCR function
IMAGE Aspect Wide, Auto, 4:3 Set aspect ratio
COLOR TEMP. Color temp.Warm, User, Cool, Adjust color temperature
Red 0~100 Customize RGB components
Green 0~100
Blue 0~100
OSD SETTING Language English,Español,
Русский, Français,
한국, Português,
Deutsch, Türkçe,
简体中⽂,⽇本語
Polski, Italiano,
Nederlands
Set OSD language
OSD H.POS.0-100 Adjust the OSD horizontal
position
OSDV.POS. 0-100 AdjusttheOSDverticalposition
OSD Timer 0~60 Set how long the OSD remains
open aer non-use
Transparency 0-100 Set the OSD overall
transparency
RESET Reset N/A Reset monitor configurations
MISC Signal source HDMI, VGA Display the input signal
Low blue ray 0-100 Set blue light filtering level
Mute On, Off Turn mute function on/off
Volume 0-100 Adjust audio volume
12

1. Press any one of the buttons ( M, , , E, ) to activate the navigation window.
eco
2. Press to switch Gameplus modes. According to the needs of your game,
choose the corresponding game icon. These game icons are primarily designed
to optimize your aim during shooting games, though they can be used for other
scenarios.
3. Press to switch ECO modes. These modes include Standard, Text, Movie,
Game, FPS and RTS modes and can be used to optimize settings according to
your activity. Standard mode is suitable for most activities.
ECO Modes and Gameplus Switching
13

KAMN24F75LB
24"
IPS
E-LED
200cd/m²
1920x1080
Specifications
16:9
14
75Hz
541.6x417.6x207.33mm
541.6x319.1x207.33mm
2.65kg
Adapter
VGA*1, HDMI1.4*1
DC 12V 2.5A
5ms
178 178
1000:1
3.64kg
Net Weight
Gross Weight
HDMI Cable
75x75
16.7M
YES
YES
NO
YES
YES
YES
YES
(H) / (V)
Model
Screen Size
Aspect Ratio
Backlight
Brightness
Panel
Resolution
Refresh Rate
Response Time
Viewing Angle
Contrast Ratio
VESA Mounting
Signal Inpt
Power
AMD FreeSync
Colours
Audio
Speakers
Audio Out
Accessories
Additional Functions
Flicker Free
Dimensions (w / Stand )
Dimensions (w / o Stand )
Physical Dimensions
Low Blue Light

Notes
15

Need more information?
For full product support and troubleshooting help,
head online to help.kogan.com

108.007.09302
24D2F KAMN24F75LA
2021.01.20
feihong
80G双胶纸，单色印，骑马钉
140*210mm
V02
备注：如不够页数，可以在封面封底的内面插入空白页
KOGAN