Kogan KAMOP101STMA User manual

10-In-1 Steam Mop
KAMOP101STMA
Quick Start Guide
Note: Please read carefully. Failure to follow the product instructions will void your warranty.
Read all instructions before assembly and use of the appliance. Safeguard these instructions for
future reference.
Warning
This appliance has been designed for domestic use only. It must only be used in ac-
cordance with these instructions. Kogan.com will not be held responsible for any
damage caused by improper or misuse of the appliance. ommercial use of this unit
voids the manufacturer’s warranty.
Verify that the main voltage indicated on the product corresponds correctly with the
voltage of your mains power outlet.
Rating Voltage: 220-240V, 50/60HZ, 1500W
To provide continued protection against the risk of electric shock, connect to properly
grounded outlets only.
Never force the plug into an outlet.
Do not use extension cords or outlets with inadequate current carrying capacity.
To disconnect the unit, turn the power switch to the “off” position, then remove plug
from wall outlet.
Do not use outdoors.
Do not leave the unit unattended while plugged in.
Unplug the electrical cord when not in use and before servicing.
Do not allow the unit to be used as a toy. lose attention is necessary when used near
children, pets or plants.
hildren should be supervised to ensure that they do not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they are under supervision or had instruction concerning use of the appliance by a
person responsible for their safety.
Never direct steam towards people, animals or plants.
Do not immerse the unit into water or other liquids.
Do not use if the cord or plug is damaged. If the supply cord is damaged it must be
replaced by the manufacturer or a similarly qualified person to avoid hazard.
Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or
pull the cord around sharp edges of corners.
Keep the cord away from heated surfaces.
Unplug after each use. To safely unplug, grasp the plug and gently pull. Do not unplug
by pulling on the cord.
Do not handle the plug or unit with wet hands or operate without shoes.
Do not insert any objects into openings. Do not use if any of the openings are
blocked.
Do not use without floor cloth in place.
Do not use without water in the water tank.
Take extra caution when using on stairs.
Store the unit indoors in a cool, dry area.
Keep your work area well lit.

Never put hot water or any other liquids such as aromatic, alcoholic, or detergent
products into the unit water tank. This will make the operation unsafe and damage the
unit.
Always keep the output for the steam clear. Avoid placing the steam opening on soft
surfaces that may block the flow of steam. Keep the openings free from lint, hair and
other potential obstructions to ensure proper flow.
Use only as directed in this manual.
Use only manufacturer’s recommended accessories. Use of attachments not provided
or sold by the manufacturer or authorised resellers may cause fire, electric shock or
injury.
The liquid or steam should not be directed towards equipment containing electrical
components, such as the interior of ovens.
Do not expose to rain.
Stop using the mop if there is a leakage of water and contact a qualified technician.
Do not use the unit in enclosed spaces that are filled with flammable, explosive or tox-
ic vapour such as paint thinner, oil-based paint or certain moth proofing substances.
Do not use on leather, wax polished furniture or floors, unsealed hardwood or un-
sealed parquet floors, synthetic fabrics, velvet or other delicate steam-sensitive ma-
terials.
Do not use for space heating purposes.
Do not touch hot surface.
Do not let cord hang over edge of table or counter, or touch hot surfaces.
Do not place on or near a hot gas or electric burner, or in a heated oven.
Do not use appliance for other than intended use.
are should be taken when using appliance due to emission of steam.
Product Features & Accessories

Assembly
Warning: Please make sure that the unit is unplugged from an electrical outlet.
Attaching the mop head to the main body
1. Insert the swivel joint into the designated hole in the main body and
use screw to fix tightly in place. Make sure that the mop head is
securely locked in place before use.
2. Insert the extensions handle into the designated opening in the main
body until it gets locked into place by the extensions handle lock
button.
3. Insert the power supply cord into the cord holder located at the top of
the extension handle as illustrated and then insert the power supply
cord into the upper cord wrap.
4. Place the microfiber cloth over the bottom of the mop head, ensuring
that the elastic holds the cloth securely to the head.
Using the steam mop
PLEASE READ BEFORE USE.
The unit is designed to thoroughly clean floor surfaces such as marble, ceramic, carpet,
stone, linoleum, sealed hardwood floor and parquet. Not all floor types are suitable for
steam cleaning.
On surfaces that have been treated with wax, the wax may be removed by the heat and
steam action. Do not use on unsealed flooring or let unit stand on any wood or heat
sensitive floors for an extended period of time. This could cause the wood grain to rise.
Use extra caution when using on vinyl, linoleum or any other heat sensitive floors. Too
much heat can melt down glue in the flooring. When using the appliance on laminated
floor, the laminated floor should have been laid professionally and not have any gaps or
cracks in which humidity could enter.
Test the unit on a small isolated area of your flooring prior to over-all use on any floor
surface.
Always check the use and care instructions of your flooring manufacturer before using
the unit.
If in doubt, please consult a specialist. Only use the carpet glider on carpeting and rugs.
Use of the carpet glider on other floor surfaces will cause streaking and might scratch the
surface.
Fill the water tank with water:

Make sure that the unit is unplugged. Turn the water tank cap counter-clockwise to the
open off position and remove the cap as illustrated below.
Hold the mop at a 45-degree angle and add water in the tank up to the MAX level by
using the measuring cup. Do not overfill. The maximum tank capacity is 450mL.
Replace the water tank cap and turn clockwise approximately 90 degrees to the “ LOSE”
position until the cap is tightened securely.
Hand-held steamer
The hand-held steamer is an ideal portable cleaner. It is there for you to detach and use on work
surfaces, kitchen countertops, sinks, bathrooms, windows, mirrors, tiles as well as spot cleaning
on floor carpets and rugs. Use it with an attachment – jet nozzle – or nylon brush to spray away
dirt, grease, mould and more.
How to take off the hand-held steamer
Make sure that the unit is unplugged.
1. Remove the power supply cord from the upper cord wrap and cord holder. Turn the lower
cord wrap to release the cord and remove the power supply cord from its channel.
2. Unlock the button on the extension hose and take out the hand-held
steamer.

Assembling the accessories
Note: After assembly of each accessory, add water in the tank up to the MAX level by using the
measuring cup. Turn the knob of the water tank to the “lock” position. Select the desired
temperate from “MIN” to “MAX”.
1. Insert the designated end of the
extension hose into designated hole in
the main unit. Make sure that the
extension hose is securely locked into
place before use.
Window cleaning tool
1. Loosen up the drawstring on the coral cloth and install the coral cloth onto the
designated hooks on the window cleaning tool frame and pull up the drawstring to secure
the coral cloth in place.
NOTE: Do not cover the squeegee blade. Make sure to hook up the coral cloth to all
hooks on the cleaning tool frame so it doesn’t slip or fall from the frame during use.
2. Attach the window cleaning tool to the extension hose as follows:
Aligning the lock button on the extension hose with the designated hole on the window
cleaning tool frame and then push in the extension hose until it locks into place.

Garment Steamer
Use the window cleaner tool as a garment steamer.
1. Install the microfiber cloth or the lint cloth over the window cleaning/ garment steamer
tool.
2. Attach the garment steaming tool to the extension hose as follows:
Aligning the lock button on the extension hose with the designated hole on the garment
steaming tool frame and then push the extensions hose until it locks into place.
Duster
1. Install the cleaning coral cloth onto the duster
frame.
2. Attach the duster frame to the extensions
hose as follows:
Aligning the lock button on the extension
hose with the designated hole on the duster
frame and then push in the extension hose
until it locks into place.
Table cleaner
Attach the main steamer to the square brush until it locks into place. Place the square cloth on
the bottom of the square head and make sure all the loops on the cloth are aligned with the
gripping hooks on the bottom of the square head.
Note: Press the two buttons on the square brush to take off the main steamer.
Straight Nozzle
1. To attach the straight nozzle insert the straight
nozzle into the designated hole in the
extension hose until it locks into place.

Round Brush
1. Attach the round brush by screwing it onto the
straight nozzle that connected to the extension
hose.
Bend Nozzle
1. Attach the bend nozzle by screwing it onto the
straight nozzle that is connected to the
extension hose.
After Use
1. Unplug power cord from outlet.
2. Allow mop pad to cool down before carefully remove cleaning cloth from mop head, as
cleaning cloth could still be hot.
3. Any water remaining in the water tank should be emptied prior to appliance storage.
Always empty the water tank at the end of each use.
4. Let any water (remaining as a product of condensation) drain from the steam opening
prior to storing the appliance.
5. Wrap power cord around the upper and lower cord wrap.
6. Wipe all surfaces of the unit with a soft cloth. Store in a protected, dry area.
7. Please store the unit in a cool and dry place when not in use. Do not leave it exposed to
sunlight or rain.
8. Upright storage of the unit with a wet mop pad may result in the formation of white
marks on your floor. To remove the white marks, clean area with vinegar. Make sure to
remove the mop pad before storing.

Cleaning and Maintenance
Warning: Be sure that the unit is disconnected from the power outlet when performing user
maintenance. Do not immerse unit in water.
Drain the remaining water in the tank and clean it after every use. Please use detergent to clean
the accessories (jet nozzle and round brush) when they are dirty, then wash them with clean
water and dry them in air.
How to decalcify the water tank interior
To clean calcium deposits that build up inside the water tank, add one or two tablespoons of
white vinegar to a full water tank, close the water tank cap and shake the contents. DO NOT
TURN THE STEAMER ON. Let it sit for a few hours. Then, empty the water tank and refill with
clean water and empty until it rinses clear.
Cleaning procedure to remove lime scale
If your unit begins to produce steam more slowly than usual or stops producing steam you may
need to remove lime scale. Lime scale can develop over time on the metal parts and greatly
affect the mop performance. We recommend removing lime scale on a regular basis, at least
once a month, especially in areas with hard water. The frequency of lime scale removal depends
on the hardness of your tap water and how often you use the steam mop.
To remove lime scale from the unit please follow these procedures:
1. Prepare a solution of 1/3 white vinegar and 2/3 tap water and add to the water tank.
2. Secure the position of the unit to ensure steam released is aimed away from the floor or
surrounding objects and surfaces. Plug the unit in and turn ON by pressing the power
switch. Allow the unit to produce steam until the vinegar/ water solution is used up.
3. Repeat the above procedure as many times as necessary until a normal steam flow rate is
achieved.
4. Fill the water tank with fresh water and rinse out.
5. Fill the water tank with fresh water, attach to the unit and release steam through the
system until the water tank is empty.

Troubleshooting
Warning: To reduce the risk of fire, electric shock or injury, unplug appliance from outlet before
service.
Problem Possible Cause Solution
THE UNIT DOES NOT POWER
ON
The unit is not plugged in or
turned ON
Make sure that the unit is
plugged into a proper outlet
and the switch is ON.
REDU ED STEAM OR NO
STEAM
Water tank is empty Fill water tank.
Steam nozzle is blocked. Remove mop head and clean
the nozzle.
Lime scale deposit Follow cleaning procedure to
remove lime scale found in the
leaning and Maintenance
section in this user guide.
STEAM ES APES FROM
ONNE TIONS
Attachment is not connected
properly
Turn the unit OFF and allow it
to cool down. Disconnect the
accessories and reattach them
properly.
Debris or obstructions at the
connection points
Remove the accessory and
check and clean connection
points.
THE LEANING LOTH GETS
SATURATED OR BE OMES
WET
The cloth gets saturated with
water
Remove wet cloth and replace
with a new cleaning cloth or
allow cloth to cool, then ring
out and reattach.