Kohler NEW MEMOIRS K-76563T User manual

NEW MEMOIRS
INSTALLATION INSTRUCTIONS
SS, SCR, 2D2P SHP, 8mm
8mm
K-76563T-L-SHP
SS, SCR, 2D2P SHP,10mm
10mm
K-76576T-L-SHP
-1-
·
·
·
·
·
·
2
80mm
3mm/m
·QB 2584-2007
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should fall
above 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
·The product complies with QB 2584-2007.
ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINYE ROAD, ZHONGSHAN TORCH
DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437
13-1 528437
©
©
Copyright Kohler China Investment Co., Ltd. 2015
2015
1269146-T01-B

H
B
-2-
ROUGHING-IN
Unit: mm
PARTS IDENTIFICATIONPARTS IDENTIFICATION
BHSKU
K-76563T
K-76576T 1500-2500 1850-2000
B
180 Deg Hinge Assy
180
X4
180 Deg End Cap Extrusion
180
1
Bottom Clip Assy
X2
Wall Clip Assy
X4
Handle Assy
X2 Bracket Assy
X1
Side Seal
X2
Wall Side Seal
X2
Magnetic Seal
1
Bottom Seal
X2
Screw
ST3.5X35
X8
Hollow Wall Anchor
X8
4mm Allen Key
4mm 3mm Allen Key
3mm
1269146-T01-B

STEP
1
INSTALLATION
STEP
2
Preparations: Install seals and hardware.
-3-
Mark the wall 20mm in from the
front edge of the tray on both
sides.
20mm
IMPORTANT:
MUSTTray be level
along front edge.
IMPORTANT
Tray must be level in all planes
or door will not install properly.
0mm
Wall Side Seal
Fixed Glass
1269146-T01-B

Install door glass.Install hinge onto the fixed panel. Pay attention to the
hinge position and leave the door open.
STEP
3
Mark lines, drill holes and insert anchors to install
fixed glass.
STEP
5
STEP
4
The wall jamb
be kept
vertical.
must
6mm
20mm
The two glass shall be level with each other.
Fixed Glass
1269146-T01-B

-5-
Adjust door glass to be level. Fix bottom clip, bracket and handle.
STEP
6
Fix seal, magnetic seal and bottom threshold.
STEP
7
6mm
The door glass shall be level with each other.
10mm 22mm 10mm
Fix Bottom Seal
1269146-T01-B

-6-
STEP
9
Do not use the enclosure for at least 24 hours.
24
24hrs
Apply silicone sealant to bottom of the fixed glass
and both sides of the bottom threshold.
STEP
8
1269146-T01-B