Kohler C3-500/K-31331T-HC-0 User manual

English page 2-8
中 文 页 码 9-15
Installation Guide
安装说明
Smart Seat
清舒宝智能便盖
C3-500/K-31331T-HC-0
C3-510/K-31332T-HC-0
1361650-T01-B

Thank You For Choosing Kohler Company
Thank you for choosing a Kohler product. Kohler craftsmanship offers you a
rare combination of proven performance and graceful sophistication that will
satisfy you for years to come. The dependability and beauty of your Kohler
product will surpass your highest expectations. We are very proud of our
products here at Kohler and we know you will be too.
Please take a few minutes to study this Homeowners Guide. Pay special
attention to the care and cleaning instructions.
All information in this manual is based upon the latest product information
available at the time of publication. At Kohler, we constantly strive to improve
the quality of our products. We reserve the right to make changes in product
characteristics, packaging or availability at any time without notice.
1361650-T01-B
2
Kohler Co.

Before You Begin
Tools and Materials
□
□
□
□
□Follow local plumbing and construction codes.
□Do not use extension cord with the product.
□
□
□
□
□Connect only to tap water.
□Unplug the seat and drain completely, if the seat is not being used for an
extended period of time.
□
Adjustable wrench Blade Screwdriver Tape Rag
Note:
Warning:
Risk of electric shock, fire hazards, or personal injury. This product must
be installed safely. Connect only to dedicated 220V~, 50 Hz, 10A circuit
protected by Ground-Fault Circuit-Interrupters (GFCI’s) or Earth-Leakage
Circuit-Breakers (ELCB’s).
Risk of electric shock or product damage. Do not immerse the product into
water.
Risk of product damage. Do not plug in the seat until all other installation
steps have been completed.
Risk of product damage. Do not install at a place where it may be splashed
by water.
Risk of product damage. Do not install the product at a place with excessive
humidity, where moisture may condense at the surface of the product. Please
maintain that the usage environment is under adequate ventilation, so as to
prevent damage to electronic components.
Risk of product damage or property loss. Water leakage may happen if the
water pipe connector is pulled or pressed with excessive force.
Risk of product damage. The product may be damaged if the nozzle is
applied with excessive force.
Risk of product damage. Make sure the seat is positioned correctly so that it
can be connected to the thread of the inlet pipe. Otherwise, the inlet pipe
thread may wear off and lead to water leakage.
□Min water pressure 0.07Mpa (dynamic pressure)
Max water pressure 0.74Mpa.
When install the product in the room, a stop valve shall be installed in a close
proximity. For emergency circumstances, the water inlet valve shall be stopped
without using any tools; otherwise unexpected failure may cause the loss to the
customer.
Kohler Co.
3
1361650-T01-B

1. Distance between installation holes: about 140mm.
2. Distance between installation holes and tank front rim:>20mm.
3. Distance between installation holes and bowl inner rim: ＜70mm.
4. Distance between installation holes and tank top rim: 460 - 490mm.
5. Bowl inner diameter: 370 - 390mm.
6. The distance between the seat and the plug should be maximum 1 meter.
1. Toilet roughing-in requirements and installation tips
2. Install an Electrical Outlet
1
2
3
4
5
3. Preparation
WARNING: Risk of electric shock, fire, or personal injury.
It is recommended to use water-resistant socket. Do not use an extension cord
with the product.
NOTE: Follow local codes when determining the electrical outlet location.
Route the electrical and install to a 220V~, 50 Hz, 10A GFCI- or ELCB-
protected receptacle.
Turn off the water supply to the toilet.
Flush the toilet to relieve any pressure from the water supply hoses.
Place a container under the inlet valve to catch any residual water.
Disconnect the water supply hose from the inlet valve.
Remove the existing toilet seat.
This product must be grounded. Connect only to a dedicated
220V~, 50 Hz, 10A circuit protected by Ground-Fault Circuit-
Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).
1361650-T01-B
4
Kohler Co.

2. Install the Mounting Plate
Place mounting plate above seat installation hole.
Insert each screw into washer, pay attention to washer direction: bending area
close to installation holes goes upwards.
Insert screws into mounting plate and toilet installation holes.
.etalpgnitnuomehtfosevorgehtotnitserotosrehsawevoM
Tighten nuts on each screw manually.
Screw
Nut
Place mounting plate above toilet mounting holes.
Insert each screw into washer.
For toilet with threaded insert:
Insert screw into mounting plate and toilet installation hole, move washer so to
rest into the grooves of the mounting plate. Pay attention to washer direction:
bending area close to installation holes goes upwards.
Tighten screw lightly along the threads. For future adjustment, do not over
tighten the screws.
For other toilets:
Note: select proper mounting plate, pay attention to installation distance indication
on mounting plate.
Note: some toilet with threaded insert on bottom board, the nuts is not necessary.
Kohler Co.
5
1361650-T01-B

3. Install toilet cover
Arrow 1
Lift toilet cover up to 15°-25°angles, toilet cover bottom align with mounting
plate, insert into the groove, and release cover. The click sound indicates the
completion of the installation.
Note: mounting plate may need to be adjusted to completely align the relative
position of the toilet.
For toilet with threaded insert:
To adjust cover position, remove cover if necessary, re-adjust mounting plate
position.
Once the mounting plate is confirmed, remove cover, fasten mounting plate
tightly.
Re-install toilet cover.
For other toilets:
Instead of remove toilet cover, only loose nut to adjust cover position. Adjust
cover and mounting plate position, when proper position gained, directly tighten
the nut, do not worry the screw will be turned along.
1361650-T01-B
6
Kohler Co.

T-valve
Supply Stop
IMPORTANT! Risk of product damage. Align water inlet hose thread with cover
thread, do not damage threads or over tighten connector. To tighten the connector,
manually tighten and then tighten 1/4 turns more by tool.
IMPORTANT! Risk of product damage. Do not scratch the product surface.
Connect the T-valve directly to toilet water inlet port.
Note! For newly installed plumbing pipes, before connecting water inlet hose to
the T-valve, flush several seconds to remove the dirt and debris, etc inside the
hose.
Use supplied hose to connect Tee-valve to cover.
Note! use supplied new hose; do not reuse the old hose.
Connect T-valve to water supply system (valve shall be purchased by customer)
Turn on water supply system.
Note! Flush the water supply pipes completely to remove debris. The product
is designed for tap water. Make sure not to use industrial water, sewage water,
waste water and ocean water.
Check water leak, adjust if necessary.
4. Connect the Water Supply
Kohler Co.
7
1361650-T01-B

5. Installation Checkout
Ensure if water inlet valve is OPEN.
Wrap seat with plastic sheet to prevent splash water from toilet during test.
Toilet generates one short beep once it is plugged in. The nozzle stretches
out and draws back once. Backlight on the side panel lights up and the night
light flashes until the initialization process completes.
Snap hose and power cord into the clip.
The seat is designed not to function without an occupant. To activate the seat
controls for testing purposes, when facing the toilet, place your hand or a damp
wash cloth on the right side of the seat approximately 1/3 from the front of the
seat (sensor area).
Proceed to the “Keypad and Panel Diagram” Section to test the various seat
functions.
1361650-T01-B
8
Kohler Co.

谢谢您选择科勒公司
谢谢您选择科勒。科勒技术提供了可靠性能和优雅生活的结合，满足了
您未来几年的需求。科勒产品的美观和可靠性将满足您最挑剔的眼光。
我们为我们科勒的产品感到非常地自豪，相信您也会。
请花几分钟阅读一下这本用户手册，特别注意维护和清洗说明。
这本说明书中所有的信息基于最新公开的产品信息。在科勒，我们一贯
坚持改善我们产品的质量。我们保留在任何时候不通知的情况下改变产
品特性，包装或实用性的权利。
Kohler Co.
9
1361650-T01-B

安装之前
工具和材料
□触电，火灾或人身伤害的危险。本产品必须安全接地。只能连接到专
用的220V~, 50Hz, 10A带接地故障断路器或接地漏电保护器的电路中。
□触电或产品损伤的危险。不要把产品浸入水中。
□产品损伤的危险。在所有其他安装步骤结束之前不要插电源线插头。
□产品损伤的危险。不要把产品安装在水可能溅到的地方。
□ 遵守所有当地的管道和建筑标准。
□ 不要使用延长电线连接产品。
□产品损伤的危险。不要把产品安装在过分潮湿的地方，在这种地方，水
汽可能凝聚在产品表面。请始终保持使用环境有足够的通风，以防止电
子组件的损坏。
□产品损坏或财产损失的危险。硬推、硬拉水管接头可能造成水渗漏。
□产品损坏的危险。不要在喷嘴上施加过大的力，否则产品可能损坏。
□产品损坏的危险。连接本产品进水管时要小心对正螺蚊，否则会损坏产
品进水口螺纹，造成漏水。
□最小进水压力0.07Mpa（动压）
最大进水压力0.74Mpa。
□ 只能连接到自来水的水源。
□ 如果产品长时间不用，请拔下插头并排干本机里的水。
□
擦布
注意：
警告:
在安装本产品的同一房间中，需要在触手可及的位置安装一个进水角
阀，用于紧急情况下，无需借助工具即可切断本产品的进水水路；否
则本产品的意外故障可能会导致用户损失。
1361650-T01-B
10
Kohler Co.