Kohler Purist Upgrade K-99170T User manual

13-1 528437
INSTALLATION INSTRUCTIONS
10mm
SCREEN 1D1P, SEALED, 10mm C
K-99170T
PURIST UPGRADE
-1-
, 2014
Copyright Kohler China Ltd., 2014
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
3
(
) 80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1227975-T01-A

-2-
ROUGHING-IN
Unit: mm
BH
SKU
K-99170T 900-1600 2000-2500
Wall Channel
Glass Clamp
Door Glass
Bottom Frame
Hingelite Panel
Side Seal
PARTS IDENTIFICATIONPARTS IDENTIFICATION
Top Frame
Transom
Side Frame
B
H
Purist Top Hinge Assy
Purist Bottom Hinge Assy
Purist Handle Assy
Purist Transom Pivot Assy, 1D1P
Purist Transom Pivot Assy, 1D2P
X1
X2 X13
X13
4mm Allen Key
4mm
3mm Allen Key
3mm
2.5mm Allen Key
2.5mm 2mm Allen Key
2mm
1227975-T01-A

0mm
STEP
2
STEP
1
-3-
·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Masonry Drill & 6mm Drilll Bit
Level
Drop Cloth
Materials Required
Tape
Silicone Sealant
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
6mm
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
INSTALLATION
Pre-install the bottom rail with seals and then put it
onto the threshold.
Pre-install seals onto the wall channel and then fix it.
6mm
Wall jamb
be plumb.
MUST
Align
1227975-T01-A

-4-
STEP
4
STEP
3
Insert the hingelite panel into the wall channel.
STEP
5
Fix the wall channel on the other side by following the
same steps.
Pre-install seals onto the wall channel and then fix it.
Make sure the ceiling is firm enough and then fix the
top frame onto the ceiling.
Fix the bottom hinge onto the side panel.
STEP
6
Align
1227975-T01-A

-5-
STEP
10
STEP
9
Fix the upper hinge onto the door glass. Remove the upper and bottom hinge covers and the
clamp plates.
STEP
8
Tighten the screws of the wall channels and clamp the
side panels.
Adjust the two side panels to make them about
662mm apart.
662mm
When adjusting the
side panels, please clamp
as much of the hingelite
panel as possible.
Note:
STEP
7
<8
662
662
1227975-T01-A

-6-
STEP
12
Fix the clamp plate into the bottom hinge to tightly clip
the glass. Pay attention to the direction of the rubber
gasket.
STEP
11
Lift the door glass and insert into the bottom hinge.
STEP
13
Fix the upper clamp plate. Adjust the rollers to make
the door glass level. Tighten the clamp plate.
Ensure the door is fully
supported at all times.
IMPORTANT:
0mm
STEP
14
If 90 degree is not suitable, please turn the set screw
slightly and try again.
90
1227975-T01-A

-7-
STEP
16
STEP
15
Install door handle. Fix the transom assembly to the side panel and wall
channel. Do not tighten the screws.
()
STEP
17
STEP
18
Fix the transom to the assembly, adjust the gaps on
each side and then tighten the screws.
Fix door seal and side seal.
Inward-opening door
Outward-opening door
Inside
Inside
Outside
Outside
1227975-T01-A

-8-
STEP
19
Fix bottom seal.
STEP
20
Insert side seal between side panel and top frame.
Insert decorative seal into top frame.
Insert seals into two sides of the transom panels.
STEP
21
STEP
22
Drill a 3.3 hole. Fix the bottom hinge and side panel
block to the bottom panel.
3.3
Fix upper and bottom hinge covers.
1227975-T01-A

-9-
STEP
23
Tighten the upper and bottom hinge covers by
tightening the screw.
STEP
24
Fix decorative cover of the transom assembly.
STEP
25
STEP
26
Apply a thin layer of silicone sealant on the bottom
frame.
24hrs
Do not use the enclosure for at least 24 hours.
24
1227975-T01-A