Kohler OVE K-1788T-1P/58 User manual

OVE
INSTALLATION INSTRUCTIONS
( //)
INTEGRATED ACRYLIC BATH (W/APRON/DRAIN/PILLOW)
K-1788T-1P/58 K-1789T-1P/58
, 2007
Copyright Kohler China Ltd., 2007
-1-
A.
·
·
A. Summary Of Key Requirements
Observe all local plumbing codes.
Install the unit to a level subfloor.
·
·
B. Product Inspection
Uncrate and inspect bath for damage. All Kohler s
baths have been manufactured with sophisticated
craftsmanship. However, please inspect for any
possible damage that may have occurred in transit.
Leave all materials in the crate during construction to
prevent damage.
Damage occurred during transit shall not be
covered by warranty.
’
NOTE:
B.
PRODUCT REQUIREMENTS
·
·
·
·
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Please provide adequate available space for the
bath unit in accordance with rough-in. Arrange the
location of drain in advance.
All installations must comply with council and local
authority by-laws. It is the responsibility of the installer
to ensure that the waste is made watertight by means
of silicone sealant or caulking compound.
Bath drain supplies should be arranged preliminarily
according to the selected bath.
please leave these
instructions for the consumer.
IMPORTANT:
NOTE: Bath can be installed after the wall is completed.
·
·
·
·
BEFORE YOU BEGIN
368 201419
1093393-T01-A

SITE REQUIREMENTS
A.A. Preparation
Check the flooring under the bath, and make repairs as
needed. Make sure the is level.
Subfloor
subfloor
C.
C. Clearance Requirements
Check the rough-in and room dimensions to provide
adequate available space for the bath unit.
·
·
·
·
·
·
·
·
·
Adjustable pipe
wrench
Rule
Level
Safety shoes
Safety glasses
Square
Screwdriver
Pliers
Utility knife
·Adjustable wrench
·
·
·
·
·
·
·
Plumbers putty
Wall coverings(as necessary)
Silicone sealant
Gypsum cement(optional)
Construction adhesive
(optional)
Protective covering for
bathtub
Nails
B. Materials RequiredA. Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
()
()
()
B.
A.
INSTALLATION REQUIREMENTS
-2-
BEFORE INSTALLING UNIT
A.A. Protect the Bath Unit
Position a protective covering or similar material in the
bottom of the unit. Be careful not to scratch the bath
surface.
1093393-T01-A

-3-
INSTALL THE BATH
A. Locate the bath in the proposed position
Adjust the feet under the bath to make it level. Tighten
the nut to fix the height of the bath.
The bath must be installed level on all top edges.
Floor should be flat, level and free of any bumps or
protrusions.
Keep the clearance of minimum 15mm from floor to
the apron for installing the apron. Be careful with the
drain hose to prevent it to be squeezed.
15
IMPORTANT:
!
!
!
!
A.
Gasket, Overflow
Handle
Cover, Overflow
Fix Clip Assy
Flexible Pipe,
Overflow
Control Cable
O-ring for Overflow outlet
O
Screw
Bath Wall
Seal Plug
Adjustable Nut
Adjustable Screw
Fix screw, Strainer
Gasket, Thin, Drain
Gasket, Thick, Drain
Joint Nut
Joint Gasket
PVC Gasket
Fix Clip Assy
B. Plumbing Installation
CAUTION: Risk of damage to bath bottom and
subfloor.
1.
2.
The drain has been installed onto the bath before it
leaves factory. Fill the bath with water before the
bath is securely positioned so as to check the
supply connections for leaks. Kohler Co. shall not be
liable under its warranty or otherwise for damage
caused by negligence.
When the bath is securely positioned, connect the
drain to the trap and apply silicone sealant.
)
)
Plug Body
Strainer
Fix Clip Assy
PVC Pipe
PVC
Flexible Pipe
B.
1).
2).
Minimum 15mm Gap
15
Adjustable Feet
1093393-T01-A

-4-
C. Install and Remove the Apron
If the apron needs removing, please follow the steps
below:
1) Remove the screw cap and loosen the screw.
2) Push the upper part of the apron inwards, pull down
the apron and it can be removed easily.
3) When installing the apron, insert the top of the short
apron into the enclosement, and push it upwards,
then insert the top of the long apron into the
enclosement, and later fix and cap the screws.
C.
1).
2).
3).
D. Apply Sealant
1. After the bath is fixed, apply sealant around the bath.
D.
1.
2
Mequiars 28 ( )
()
Cleaning and Care
Cleaning Acrylic Surfaces: Do not use abrasive
cleansers on any acrylic surfaces, as they will scratch
and dull the surface. Wipe out the bath after each use
to prevent a build-up of soap and scum.
If the acrylic surface becomes dull, an automotive type
rubbing compound may be used on the unit, followed
by an application of paste wax.
We recommended:
Rubbing compound mequiars mirror glaze 28 metal
polish (import product) or "green oil".
IMPORTANT CONSUMER INFORMATION
Apply Silicone
Sealant
Apply Silicone Sealant
Apply Silicone Sealant
Apply Silicone Sealant
1093393-T01-A