Kohler BEAM K-77691K-G User manual

-1-
BEAM
INSTALLATION INSTRUCTIONS
URINAL FLUSH VALVE
K-77691K-G/K-77692K-G/K-77693K-G
BEFORE YOU BEGINBEFORE YOU BEGIN
TOOLS AND ACCESSORIESTOOLS AND ACCESSORIES
·
·
Congratulation on your purchase of this high quality
Bathroom Accessory. Before proceeding with the
installation, please carefully read this installation
instruction in order to ensure proper care and assembly of
this accessory.
Please keep this installation instruction for future
reference.
Prior to drilling into walls, check there are no hidden
electrical wires, cables or water supply pipes with the
aid of ar, electronic detector. If you use power tools do
not forget:
1. Wear eye protection.
2. Unplug equipment after use.
·
·
1.
2.
KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,
JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436
( ) 158 200436
ROUGHING-IN
UNIT : mm
Reference Value
Drill Leveling Instrument Screw Driver
Wrench Screw X9
9
Saw
Tape Hammer
1.5mmHex Wrench
1.5mm
G1/2 & G3/4 Screw Die Machince
G1/2 G3/4
Kohler reserves the right to change marked dimensions without prior notice.
Fig.1
1
144
194.5
180
166
( G1/2)
93
200
62
25
61
200
228
( G3/4)
©
©
Copyright Kohler China Investment Co., Ltd. 2017
2017
1296231-T01-C

-2-
INSTALLATION
1. Drill wall
Draw lines and drill the wall according to Fig.2. The horizontal
distance between the bottom of plate and the top surface of
urinal is advised to be 230mm. Depth can be adjusted as
desired.
1.
2
230mm
Fig.2
2
240
196
2.
3
( G1/2 )
4·
·
2. Fix box
Note:
Insert the box as shown in Fig.3. Adjust and fix the box
with 4 screws.
Cut the inlet and outlet pipes as shown (G1/2 female
thread for inlet pipe)
The inlet and outlet pipes shall be cut level and clean
and ensure its proper vertical and horizontal level.
·
·
Fig.3
3
Screw
Inlet Pipe
Outlet Pipe
DN20mm(G3/4)
DN20mm(G3/4)
SPECIFICATIONS
SKU K-77691K-G/K-77692K-G/K-77693K-G
Flush Volume 0.5L, 1L, 3L
Minimum Water Pressure 0.05mpa(Dynamic Pressure )
Maximum Water Pressure 0.75mpa(Static Pressure )
Water Temperature 1 ~50
1296231-T01-C

3.
3. Cut box
Cut the excessive part of the box as shown.
-3-
Fig.4
4
Fig.5
5
4.
5
·
·
·
·
·
4. Install valve assembly
Fix onto inlet pipe
Fix onto outlet pipe
Note:
Fix valve assembly onto inlet and outlet pipes with wrench as
shown in Fig.5.
Process inlet pipe thread and fix inlet pipe connector.
Put seal onto the nut.
Tighten valve assembly and inlet connector with wrench.
Put nut and seal onto outlet pipe.
Tighten valve assembly and outlet connector with wrench.
Clean waste in the supply pipe before fixing inlet pipe.
·
·
·
·
·
Valve
Nut
Seal
Outlet Pipe(Not Supplied)
()
1296231-T01-C

5.
6
5. Cut and fix tile
Cut tiles as shown in Fig.6.
-4-
Fig.6
6
155mm-161mm
124mm-130mm
6.
;
(17.8 );
6
+1
0
·
·
·
·
·
·
·
6. Fix bottom board
Note:
Tighten the 6 screws on the bottom board.
Cut the rod connector according to the depth into the tile
.
Fix the rod connector to the valve rod.
Do not overtighten the nut to avoid deforming or
damaging the bottom board.
Test run and check the valve after installation.
Water continues running at flush valve: Check whether
the rod is still too long. Continue press the rod with the
button to make the valve continue working.
No water or too little water running from the valve: Check
whether the rod is too short.
Connect the manufacturer for any other problems.
(17.8 )
+1
0
·
·
·
·
·
·
·
Fig.7
7
Fig.8
8
Screw
Bottom Board
Bottom Board
17.8 +1
0
1296231-T01-C

7.
;
;
L
3mm
3.5mm
·
·
·
7. Fix faceplate
Note:
Put the faceplate onto the bottom board.
Pull the faceplate downwards.
Tighten the rod with L wrench.
When removing the faceplate, unscrew the screw 3mm
out and push the faceplate 3.5mm upwards to remove it.
·
·
·
Faceplate Assembly
Button Assembly
Top Screw
Wrench
Fig.9
9
Lock
Pull
Snap
8.
7
·
·
·
8. Maintenance
Test run and check the valve after installation. Leakage at
inlet connector:
Refer to Fig.7 to check whether the seal is properly
installed, nut is tightened and whether the inlet pipe is at
proper vertical and horizontal level.
Leakage at outlet connector: Check whether the surface is
smooth, the seal is twisted and the nut is tightened.
Water cannot be stopped: Press the rod to check whether
it can be restored, there is wastes inside and valve
assembly is blocked.
·
·
·
-5-
1296231-T01-C