Kohler K-CB-CLW2030DAW User manual

1070225-2-A
1
CLW CABINET INSTRUCTIONS
CABINET MODELS: K-CB-CLW1526SS, K-CB-CLW2026SS, K-CB-CLW2030DAW
GENERAL NOTES
1. If you are surface mounting the cabinet on the wall
see instructiosn on page 2.
2. A surface mounted cabinet requires the optional
Mirror kit supplied with your cabinet.
3. If you are recessing the cabinet in the wall,
see instructions below.
4. Call our customer service - 1.800.4.KOHLER
between 8 a.m. and 5 p.m. C.S.T. If you have any
questions or require parts. Have the serial number
from inside the cabinet before you call.
444 Highland Drive. • Kohler, WI 53044
Mounting location for
#8 x 1 1/2" philips
head screws
25 1/4" high
14 1/4"W for CLW15 Models
19 1/4"W for CLW20 Models
ROUGH OPENING DIMENSIONS
1. RECESSING THE CABINET INTO THE WALL.
One Year Limited Warranty
Top View
Stud and wall
surface
Install dome caps
over screws.
Cabinet flange fits
flush against wall.
Fig. 2
Install screws through
holes in cabinet as
shown in Fig. 1
DO NOT OVER-
TIGHTEN!
Fig. 1
For the U.S.A. and Canada Only
KOHLER plumbing products are warranted to be free of defects in material and workmanship
for one year from date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler
Co. inspection discloses any such defects occurring in normal usage within one (1) year after
installation. Kohler Co. is not responsible for removal or installation costs. Use of in-tank toilet
cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing
Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn.: Customer Service
Department, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER
from within the USA, 1-800-964-5590 from within Canada and 001-877-680-1310 from within
Mexico.
Implied warranties including that of merchantability and fitness for a particular purpose are
expressly limited in duration to the duration of this warranty. Kohler Co. and/or seller disclaims
any liability for
special, incidental or consequential damages.
Some states/provinces do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of special, incidental or consequential damages so these limitations
and exclusions
may not apply to you. This warranty gives you specific legal rights.You may also have other
rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.

2
Fig. 4B & 4C
4B
4C
INSTALLER’S NOTE:
Installing the cabinet on a wall without the door attached can make
installing easier for one person. Do not mount the doors until the box is
in or on the wall.
Wall anchor
(if required)
Top mount clip
#8 x 2" Hex head screw
(Use 1/4" driver)
2. SURFACE MOUNTING THE
CABINET ON A WALL.
A. Install Mounting Bar.
1. Drill two 3/16 holes in bottom mounting bar at indent location.
Use the supplied anchors or locate studs if possible.
2. Drill 3/16” hole in wall for mounting bar anchors at locations
shown in Fig. 3. (If you do not use the anchor, drill a 3/32”pilot
hole.) After the holes are drilled, t the mountingbar onto the
wall, refer to Fig. 3 for measurements, and Fig. 5 or information
on anchor cinching.
B. Install Top Clips
(Left and right top clips come connected, hold both clips and snap
them apart).
1. Fit cabinet into position on mounting bar as shown in Fig. 4A.
2. Place clip in position as shown in Fig. 4B and mark with a
pencil. Remove clip and cabinet and drill the pilot or anchor
holes where marked.
3. Fix both the clips into position with a screw, and slide the clip
into the up position. Sit the cabinet on the mounting bar, then
lower and tighten the screws into place, as shown in Fig 4C.
4. See Fig. 5 for proper turns required for anchor cinching.
5. See page 3 for Side Kit Mirror application.
Cabinet bottom sits
in lip on bottom
mounting bar
#8 x 2" Hex
head screw &
Wall anchor
(use 1/4" driver)
11" bottom mounting bar for CLC15/20
Fig. 4A
Fig. 3
3/4"
4 1/2" from edge
Bottom of Cabinet
2" from edge
CLW20
CLW15
Side of Cabinet
Fig. 5
Once Screw is bottomed out on
mount clip, turn screw an additional
5 to 7 turns to fully expand the anchor.
Side view at top of cabinet
1070225-2-A

3
3. ATTACHING SIDE KITS TO A SURFACE
MOUNTED CABINET
1. Apply foam tape to Side kit bracket
A. Peel tape from sheet, leave liner on.
B. Apply as shown to side kit brackets, be sure they are
clean and dry.
C. DO NOT PEEL RELEASE LINER UNTIL YOU
HAVE TEST FIT THE MIRRORS ON THE
CABINET!
2. Attach the side kit brackets to the cabinet as shown
in Fig. 6
3. Test t the side kits, then clean the back of the side kits
with rubbing alcohol.
4. Peel the release tape from the brackets and apply the
side kits, push rmly to set.
5. Cover the screw heads with the screw caps.
Align top of side kit with top of flange
Side kit bracket
(Fits tight under the
flange of cabinet)
#8 x 3/8" screws
self thread into
Side Kit brackets
Side Kit brackets
2 pieces
26" high
Fig. 6
4. DOOR ADJUSTMENTS
8-32 x 1/2"
6-32 x 3/8"
A
B
B
A. This screw releases the door from the cabinet and
allows up and down adjustment. Fig.7
B. These screws allow you to plumb
the door as shown in Fig. 8.
C. The screws you use for attaching the hinges.
(Supplied with hinges)
Fig. 7
Fig. 8
1070225-2-A

4
6. INSTALLING THE SHELVES – see Fig. 10
1. Push/twist the pins
into place
A. Push one side of
the shelf into the
left or right clips
B. Snap the shelf
down into the
opposite side. If
the shelf is too
tight, repeat the
process from the
other side.
2. Fill the remaining
holes with the plugs.
Fig. 10
Door
Bumper
5. INSTALLING THE TOOTHBRUSH COVERS & DOOR BUMPERS – see Fig. 9
1.
Install the clear door bumpers in the round indent
area at the top and bottom of the door.
Fig. 9
A
B
2
Parts supplied with your cabinet. (For cabinet body and door replacement, call customer service with model
number.) Be sure to check the cardoard supports in the carton, glass parts are packed in them.
4 Side Kits brackets Part List - BAGCLCS (silver) BAGCLCW (white)
2 Glass Shelves
1 BC-BAGCLCHGE
Hinge Kit
Snap-in Pins
Side
Mirrors
11” Mounting Bar Door Bumpers #8 X 1/2” Phillips
Head Screws
Screw Caps
Silver or
White
Top Clips
Wall Anchors
#8 X 2” Hex Head Slotted
Screws
Hole plugs
White or
Silver
4 Side Kits Bracket
Foam tape
Checklist • Care & Maintenance
1. Cleaning
A. The cabinet door and interior are constructed of mirror and
aluminum. Use only a damp cloth to clean. Spray the cloth,
not the mirror when cleaning. Mirrors are damaged by the use
of ammonia or vinegar based cleaners. Rubbing alcohol can
be used for stubborn stains.
B. Use no abrasive cleansers on any part of the cabinet.
C. The white frame should be cleaned with a damp cloth only.
#8” X 3/8” Screws
1070225-2-A
CB-BAGCLCS(Sliver) or
CB-BAGCLCW(White)
(CB-SHLFCLC15 &
CB-SHLFCLC20)
(CB-RO331100M)