Kohler Memoirs 485T User manual

BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTE:
These products should be located and mounted toawall. While it is possible to mount them to any surface, a stud
or concrete mounted product will yield the best results.
DANGER: (Risk of personal injury )
These products are not designed or intended for use asagrab bar or support bar. Do not install where the product
might be used as a grab or support bar.
1243009-2A-A 1
ROUGH-IN DIMENSIONS
ACCESSORY INSTALLATION INSTRUCTIONS
**Color code must be specified when ordering
ACCESSORY SERVICE PARTS
485T 18″ Towel Bar
486T 24″ Towel Bar
487T Towel Ring
488T Glass Shelf
490T TP Holder
492T Robe Hook
10454T Dual TP Holder
10456T Soap Dish
37352T Covered TP Holder
37353T 24″ Double Towel Shelf
37354T Toilet Brush Holder
37355T 24″ Double Towel Bar
1104400**
1104400**
57597
1002853**
1093960**
1104399**
1046290
59608
1061576
1041023
1001912
1243009-2A-A 8
10454T Dual TP Holder
485T
504
457
25
47
72
84
7
486T
72
84 25
47
609
656
25
47
629
676
132
488T
7
7
33
33
33

1243009-2A-A 2
487T 490T 492T
47
181
25
84
72
162
155
47 84
81
84
47
47
25
54
47
25
124
90
7
7
7
96
119~144
84
33 33
33
119~144
170~195 170~195
387~437
Ø39
103.5
25
47
10454T
78
Ø120
54
25
47
142
82
33
10456T
7
73
128
33
25
157
127
37352T
7
37354T
25
72
130
346
47
47
86
156
75
47
47
1061576
1001912 57597
1002853**
1041023
1046290
59608
1041023
52092
1057882** (457 mm)
(610 mm)
1057883**
52307
1001886**
1003079**
1001885**
1041023
52307
1003079**
870973
1157348**
1157348**
870973
1157348**
870973
77434
ACCESSORY SERVICE PARTS
1243009-2A-A 7
**Color code must be specified when ordering
485T 18″ Towel Bar
486T 24″ Towel Bar
488T Glass Shelf
37353T 24″ Double Towel Shelf
37355T 24″ Double Towel Bar
Only for 488T
33
33
33
33
65
7
7

1243009-2A-A 3
7
7
25.4
25.4
33
37355T
37353T
600
146
647
47
47
79
33
72
216
610
47
662
120
47
38
104.5
How To Install The Bracket
Only For 485T/486T/488T/37353T/37355T
As Fig 1 shown, select a proper position on the wall to stick the templet, ensure
the templet is horizontal and keep the smaller hole downward as shown. Drill
hole in the finished wall as required.
Only For 10454T
Select a location to install tissue holder. As Fig.2 shown, mark the center point
on the finished wall, and keep the center-to-center distance at 170~195mm.
Use a level to ensure that all center points are horizontal and equidistance.
Mark anchor(1) hole location vertically 12.7mm above and below the center
point as Fig.3 shown. Drill hole in the finished wall as required.
Note: Ensure that all center points are horizontal, otherwise may result in slant
of tissue holder.
Only For 487T/490T/492T/10456T/37352T/37354T
Select a location on the vertical wall to install the bracket. As Fig 4 shown, mark
anchor mounting hole location on wall as shown, ensure the large slotted
mounting hole of the plate upward, the smaller hole of the plate downward and
two screw holes are vertical. Drill hole in the finished wall as required.
For All Products
As Fig 5 shown, press the anchor(1) into the hole. Orienting the large slotted
mounting hole of the plate upward, the smaller hole of the plate downward and
two screw holes are vertical, secure the plate(2) with the self-tapping screw(3).
P N: XXXXXXX
3
2
1
Fig.1
170~195mm
12.7mm
12.7mm
170~195mm
Fig.2
Fig.3
Fig.4
Fig.5
INSTALLATION
Center point
Mounting hole
Level
Center point
ACCESSORY SERVICE PARTS
1046290
1061576
57597
1002853**
1001912
59608
1041023
1169924
1119664
1119648**
1093960**
79138
79138
1001740**
36715**
487T Towel Ring
490T TP Holder
492T Robe Hook
10456T Soap Dish
37352T Covered TP Holder
37354T Toilet Brush Holder
1014802
1243009-2A-A 6
**Color code must be specified when ordering

1243009-2A-A 4
How To Install The Bonnet
Position the escutcheon(4), if included, onto the bonnet(6).
Slide the bonnet onto the bracket(2). Orient the setscrew hole of the bonnet
downward. Make sure the bonnet pin(5) engage the indexing hole in the back
of the escutcheon, if applicable. Insert a screw(7) into the bonnet and tighten.
NOTE: Make sure the bonnet pin engage into the escutcheon hole.
5
2
4
6
7
1243009-2A-A 5
9
6
6
8
8
36
35
9
8
38
40
37
6
39
9
6
6
8
8
41
42
43
How To Install The Toilet Brush Holder
Slide the shaft of the cylinder head(39) of the toilet brush holder kit(38) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the toilet brush holder
kit.
Slide the glass holder(40) into the toilet brush holder, then slide the brush (37)
into the glass holder. If necessary, disassemble brush from the toilet brush
holder, then reinstall the brush to the brush holder.
How To Install The Double Towel Shelf
Slide the shaft of the cylinder head(35) of the double towel shelf kit(36) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the double towel shelf
kit.
How To Install The Double Towel Bar
Slide the shaft of the cylinder head(42)(43) of the double towel bar kit(41) into
the bonnet(6), orient the cylinder head with the detent facing downward. Tighten
the screw(8) into the bonnet with the hex wrench(9) to secure the double towel
bar kit.
Ensure that all connections are tightened.
Ensure all setscrews face straight down.
INSTALLATION CHECKOUT
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. Which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
10
12
6
811
8
6
13
9
14
9
6
16
15
8
8
21
17
18
18
19
920
23
6
8
24
9
22
9
6
8
25
23
23
6
28
29 27
8
9
88
9
6
8
30
31
26
32
How To Install The Covered Toilet Paper Holder
Slide the shaft of the cylinder head(33) of the toilet paper holder kit(34) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the toilet paper holder
kit.
6
34
9
33
8
How To Install The Towel Bar
Slide the shaft of the cylinder head(11)(12) of the towel bar kit(10) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the towel bar kit.
How To Install The Towel Ring
Slide the shaft of the cylinder head(14) of the towel ring kit(13) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the towel ring kit.
How To Install The Glass Shelf
Slide the shaft of the cylinder head(16)(17) of the shelf kit(15)(21) into the
bonnet(6), ensure the brackets are horizontal and two cylinder heads with the
detent facing downward. Tighten the screw(8) into the bonnet with the hex
wrench(9) to secure the shelf kit.
Slide the shelf(19) through the slot on the bracket. Ensure the shelf is in the
center of the slot on the bracket and horizontal. Tighten the setscrew(18) with
the hex wrench(9).
How To Install The TP Holder
Slide the shaft of the cylinder head(22) of the tissue holder kit(24) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the tissue holder kit.
Disassemble the tissue spindle(23) from the tissue holder kit(24) as required,
insert roll paper and assemble it back to the tissue holder kit.
How To Install The Robe Hook
Slide the shaft of the cylinder head(26) of the robe hook kit(25) into the bonnet(6),
orient the cylinder head with the detent facing downward. Tighten the screw(8)
into the bonnet with the hex wrench(9) to secure the robe hook kit.
How To Install The Dual TP Holder
Slide the shaft of the cylinder head of the tissue holder kit(27)(28)(29) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the dual tissue holder
kit. Disassemble the tissue spindle(23) from the tissue holder kit as required,
insert roll paper and assemble it back to the dual tissue holder kit.
How To Install The Soap Dish
Slide the shaft of the cylinder head(32) of the soap dish kit(30) into the
bonnet(6), orient the cylinder head with the detent facing downward. Tighten the
screw(8) into the bonnet with the hex wrench(9) to secure the soap dish kit.
Insert the dish(31).