Kohler 72695T-B4 User manual

1301247-2A-B 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
3. The highest working pressure for handspray is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60°C. Please keep handspray, showerhead and the
shower arm away from heater, or it may become damaged and cause injury to the user.
4. These products contain natural jade material. Do not contact lipstick and other easy dyeing cosmetics.
OPERATION CONDITION
1301247-2A-B 4
INSTALLATION INSTRUCTIONS
72695T-B4 R8654T-B Wall-Mount Bath Shower Faucet
72697T-B4 Wall-Mount Shower Only Faucet
FAIRFAXFAIRFAX
ROUGH-IN DIMENSIONS
SERVICE PARTS
Lift the handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
72695T-B4 R8654T-B Wall-Mount Bath Shower Faucet
72697T-B4 Wall-Mount Shower Only Faucet
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
72695T-B4 R8654T-B 72697T-B4
162
11º
G1/2˝
52
G1/2˝
G1/2˝
Ø70
150±15
G1/2˝
G1/2˝
G1/2˝
G1/2˝
Ø70
Ø122
150±15
255
79
1500
Ø54
82.5
49
40º
27
60
58
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
72695T/R8654T:880078**
72697T:77955
72697T:1097338**
72695T/R8654T:870992
72695T/R8654T:1093365**
72695T/R8654T:835014**
72695T/R8654T:1043143**
CP:835701**
1189866**
1030624
AF/BN/BV/SN:1216770**
72695T/R8654T:834460
72697T:834793
1294251**
78148**
32725
834554
832940
836530
1093358**
834792
1218659
864675
871363
864104**
1170944**
1093359**
880010
831727**
836710**

1301247-2A-B 2 1301247-2A-B 3
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Faucet
To perform installation, installer must provide G1/2" female supply
fittings(1), spaced 150mm apart and level. The supply fittings should be
vertical and not beyond the finished wall. Hot supply pipe must be located
on the left.
Install the two offset connectors(2) into the hot and cold supply pipes.
Use appropriate thread sealants or thread tape on pipe threads.
Adjust the center-to-center distance between the connectors to 150mm
and level. They should extend 28 to 30mm beyond the finished wall.
Thread the escutcheons(3) onto the connectors until they are against the
finished wall.
Put the washers(5) into the nuts(4), thread the nuts to connectors.
When tighten the nuts, use strap wrench or soft cloth between product
and regular wrench to protect the finish.
Connect hose(8) to the faucet outlet(7), and to the handspray(9) with
washers(6).
INSTALLATION CHECKOUT
How to Install the Bracket
Determine a suitable location on the finished wall to install the bracket.
For the finish with CP: Take off the locking pin(11) from the bracket(10).
Take out the self-tapping screws(12) and anchors(14) from the inside of
the bracket by pulling out the plastic sleeve(13).
Mark bracket base mounting hole location on the wall. Drill two holes on
the finished wall as required. Press the anchors into the holes and screw
the self-tapping screws into the anchors though the sleeve. Tighten them
by screwdriver. Align the bulge of the bracket and the slot of the sleeve.
Slide the bracket onto the sleeve and insert the locking pin into the hole
of bracket and sleeve.
For the other finish: Mark bracket base mounting hole locations on the
wall according to the dimension. Drill two holes on the finished wall, the
holes should match the anchors(15). Install the anchors.
Tighten screws(16) to secure bracket base(17, flat side upward). Put the
bracket(18) onto the bracket base and lock by stopper.
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply, and check for leaks. Repair as needed.
Bath & Shower Faucet:
Remove the handspray(9) and the aerator(19). Run hot and cold water
through the faucet for about a minute to remove any debris. Check for
leaks. Remove any debris from the aerator assembly. Shut the faucet off,
and reinstall the aerator assembly and handspray.
Shower Faucet:
Remove the handspray(9). Run hot and cold water through the faucet for
about one minute to remove any debris. Check for leaks. Shut the faucet
off, and reinstall the handspray.
4
5
150mm
2
28~30
3
10
11
10
11
12
13
14
27mm
16
18
17
15
7
8
6
9
19
9
9
1
Hot
Cold
150mm