Kohler STANCE 14760A-4ND User manual

All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. An in line water filter must be used with this product.
3. Inspect the supply pipes for damage. Replace as necessary.
4. Observe local plumbing codes.
5. If possible, install this basin set before installing the basin.
6. Recommended working pressure: 100KPa to 500KPa.
7. Maximum working pressure: 800KPa.
8. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
1134199-AN2-A 04/07/11
Basin Mixer: 14760A-4ND
Tall Basin Mixer: 14761A-4ND
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
ROUGH-IN DIMENSIONS
14760A-4ND 14761A-4ND
Hob Mount Single Lever Mixer
STANCE
BASIN TAPWARE
1
G1/2"
215
88
12
135.7
57max
479
342
203
365
163.5
57max
12
G1/2"
45
45
Hot Cold
Open
Close
35~ 42
35~ 42

1.) Screw the stud(1) into the thread hole on the bottom of the faucet
body(4).
2.) Put the washer(2) into the bottom of the body(4) by inserting over the
flexible hoses(3) and stud(1).
3.) Position the faucet into the pre-drilled hole in the deck. From the
underside of the basin, fit the bracket(5), washer(6) and nut(7) onto
the stud and loosely tighten.
4.) Position the faucet on the basin. Once aligned properly, tighten the
mount nut firmly using the wrench.
5.) Fasten the G 1/2 hose fittings to the water supplies. The hoses will
be identified with red and blue stickers. Refer to the rough-in for
proper hot and cold faucet operation.
Note: If servicing the valve, carefully pry the top ring off using a plasitic
or other non-scratching tool. The top ring is a press fit with an o-ring so
it can easily be removed when required.
INSTALLATION
CLEANING INSTRUCTIONS
1.) Ensure that all coupling nuts are fastened securely.
2.) Ensure the handle is in the off position.
3.) Open the drain and turn on the main water supply and check for
leaks. Repair as needed.
4.) Remove the aerator(8) using the key(9).
5.) Turn the tap on and flush hot and cold water through the spout
for about one minute to remove any debris. Re-check for leaks
at this time.
6.) Remove any debris from the aerator.
7.) Turn the tap off and reinstall the aerator.
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a
clean soft cloth. Many cleaners may contain such chemicals as ammonia, chlorine, toilet chemicals etc. which
could adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler fittings.
INSTALLATION CHECK
SPARE PARTS
**Color code must be specified when ordering
4
1
5
6
7
2
3
1134199-AN2-A 04/07/11
3
1134199-AN2-A 04/07/11
2
8
9
Hob Mount Single Lever Mixer
STANCE
BASIN TAPWARE
Basin Mixer: 14760A-4ND
Tall Basin Mixer: 14761A-4ND
1002856
Bracket
1138660
Washer
52202
Washer
1100598**
Handle
ONLY for 14760A-4ND
78150
Nut
48694
O-ring
1138291**
Top Ring
1054593
Hose
1000535
Attachment
Stud
1
018336*
*
Mounting Nut
Cartridge Seat Kit
1108428
Valve
77953
O-ring
1088909
Setscrew
1088909
1100594**
Handle
ONLY for 14761A-4ND
300
2
868
Washer
1167451
1
1421
0
2*
*
Aerator
Housing
1180531
Setscrew
Aerator
1142493
Aerator
Key
1179018
Mounting Hardware Kit
1179017**
Aerator
Kit
300
2
868
Washer
1167451
1
1421
0
2*
*
Aerator
Housing
Aerator
1142493
Aerator
Key
1179017**
Aerator
Kit