Kolcraft Jeep S45J-A-R3 User manual

1S45J-A-R3 2/03
WARNING: AVOID SERIOUS INJURY FROM FALLING OR SLIDING
OUT.ALWAYS USE RESTRAINT SYSTEM.
URBAN-TERRAIN 3WHEEL STROLLER INSTRUCTION SHEET
IMPORTANT SAFETY INFORMATION:
•NEVER LEAVEYOUR CHILD UNATTENDEDWHILE IN STROLLER.
Accidents can happen quickly while your back is turned.You must always keep your child in view while your
child is in the stroller,even when sleeping. Your child may become tangled in straps or pads and suffocate.
•Always use restraint system to keep child from standing up or falling out of the stroller. Use this
harness at all times.
•Do not use any infant car seat with this stroller.Serious injury may occur.
•THIS IS NOT AN EXERCISE STROLLER! Do not use this product while running,jogging, in-line skating
or participating in other athletic activities.
• Always balance the weight of the stroller evenly. To prevent the stroller from becoming unstable or tipping:
• Do not place parcels or accessory items on the stroller canopy, seat,or over the handle.
• Do not put more than 10 lbs (4.54 kg) in the basket.
• Do not put more than 3 lbs (1.362 kg) in each Saddle Bag.
• Do not allow children to play with or hang onto the stroller.
•Always lock the stroller open before allowing your child in or near the stroller.This prevents injuries
caused by stroller collapsing.
•Only use this stroller with children who weigh less than 45 lbs (20.43 kg) & who’s head rests
below the top of the seat back. Use by larger children may damage the stroller,or cause a hazardous
unstable condition to exist.
•Only use this stroller in recline position until child can sit up unassisted.
•Put on all brakes whenever you park the stroller,especially on an incline. This prevents the stroller
from rolling away.
•Never use this stroller on stairways or escalators.
•Do not allow child to stand on seat or sit on footrest.
•Always fasten the hood onto the seat back when using the stroller in the reclined position.
•Do not lift by tray or toys.
•Do not allow children to climb into stroller unassisted. Stroller may tip over and injure child.
•Keep wheels at a recommended tire pressure of 35 p.s.i. (241 kPa).
•Only use replacement parts supplied by the manufacturer.
•Do not carry extra children or use accessories other than those approved by the vehicle
manufacturer.
•The stroller should not be used near an open fire or exposed flame.
•Make sure children are clear of any moving parts if you adjust the stroller,otherwise they may be
injured.
Your child's safety depends on you. Proper stroller usage cannot be assured unless you follow these instructions.
DO NOT USE STROLLER UNTILYOU READAND FOLLOWTHE MANUFACTURER’S INSTRUCTIONS.
!
S45J-A-R3
© 2003 Kolcraft®Enterprises, Inc. All rights reserved.
by

2S45J-A-R3 2/03
Step 1. Release locking latch.
(FigureA).
Step 2. Unfold as shown. Make
sure both locks snap into place.
(Figure B).
How to AssembleYour Stroller
Step 1. Remove and discard
protective plastic sleeve from ends of
rear axle assembly.
Step 2. Position rear axle
assembly as shown (Figure A), with
brake levers pointing towards stroller
handle.
Step 3. Push both brake assem-
blies onto rear leg tubes at the same
time until spring loaded buttons click
into place (Figure B).
Step 4. Lay stroller on its side.
Slide wheel onto axle. (Figure C).
Step 5. Push down on wheel until
you hear a click. Pull up on wheel
to make sure it is properly
secured. If wheel pulls off,push
wheel onto axle again but push metal
clip in at the same time. Make sure
wheel is secure (Figure D).
Step 6. Repeat for second side.
To RemoveWheel. Press
metal clip in and pull wheel off.
NOTE:Keep wheels at a recommended
tire pressure of 35 p.s.i. (241 kPa).
B
A
C
1TO OPEN STROLLER:
2TO ASSEMBLE REARTIRES:
D
A
B

Step 1. Align and place footrest
against stroller frame as shown mak-
ing sure notch in footrest fits over
metal rod that supports seat
(FigureA).
Step 2. Place stroller back on
handle bar (Figure B).
Step 3. Align bosses on footrest
to the two holes on the metal frame
over front wheel (Figure C). Feed
bosses through holes.
Step 4. Secure footrest to frame
with screws using a Phillips screw-
driver (Figure D). Repeat for second
side.
Step 5. Loop straps of basket
through slots in footrest as shown to
secure (Figure E).
Bosses
Hole
B
A
C
D
E
3S45J-A-R3 2/03
3TO ATTACH FOOTREST:

4S45J-A-R3 2/03
Step 1. Place tray onto metal
tubing between footrest and side
housing.
Step 2. Snap tab in place.
Step 3. Repeat for second side.
Step 1. To insert batteries, use a
phillips head screwdriver to unfasten
battery cover. Insert batteries as
shown. Requires 2“AA” batteries
(Not Included). Secure battery cover.
Step 2. Turn switch on“1” to
play sounds. To turn off,move switch
to“O”.
Old and new batteries should not
be mixed. Different type batteries
should not be mixed. Remove
batteries before storing the toys.
CAUTION
! !
1O
Step 1. Attach mirror to toys as
shown.
Caution: For your childs safety,
remove the following labels if found
on this toy before use:
-“Try Me” on front of unit.
- Protective film on mirror.
5TO ATTACH FRONTTRAY:
6
TO ASSEMBLE ELECTRONICTOYS
(SELECT MODELS):
7
TO INSTALL BATTERIES IN
ELECTRONICTOYS
(SELECT MODELS):
Step 1. To attach saddle bags,
feed & secure one end ofVelcro strap
through footrest. (FigureA).
Step 2. Feed and secure other
end of velcro strap through metal clip
on oval tubing.(Figure B).
!WARNING! !
DO NOT PUT MORE THAN 3 LBS
(1.362 KG) IN EACH SADDLE BAG.
4TO ATTACH SADDLE BAGS:
A
B

5S45J-A-R3 2/03
Step 1. Position toy steering
wheel on snack tray as shown.
(FigureA).
Step 2. Align rear toy tabs with
rear tray slots. Hook into place.
Step 3. Place your thumbs under-
neath tray and with fingers, snap front
portion of toy steering wheel into
front tray slots. (Figure B).
Step 4. To remove toys,press
plastic tabs on front of toy steering
wheel and pull up.(Figure C).
Rear toy tabs
Rear tray slots
Plastic tab
DO NOT PLACE MORE THAN 3 LBS. (1.362 KG)
IN THIS TRAY TO AVOID TIPPING!
DO NOT PLACE HOT LIQUIDS IN THIS TRAY.HOT
LIQUIDS CAN BURN YOUR CHILD.
!WARNING!
Step 1. Align tray holes with
posts near handle and snap on.
Step 2. To remove, pull each side
up and out. For cleaning,parent tray
is top rack dishwasher safe.
!
10
TO ATTACH PARENT TRAY
(SELECT MODELS):
9TO ATTACH NON ELECTRONICTOYS
(SELECT MODELS):
8
TO ATTACH ELECTRONIC TOYS
(SELECT MODELS):
Step 1. Place electronic toys so
that they face the child in the stroller.
Step 2. Tilt toys toward stroller
and align tabs with rear tray slots.
Lock tabs into slots (FigureA).
Step 3. Press down firmly on front
of toys until front tabs lock toys
securely in place (Figure B).
Step 4. To remove toys from tray,
press down on front tabs to release
front tabs and pull up on toys.
A
B
A
B
C

UNLOCK
LOCK
Lock Brake. Push 1-Touch
braking bar down at any location to
lock wheels.
Unlock Brake. Lift up on
braking bar to release.
3TO OPERATE BRAKES:
6S45J-A-R3 2/03
How to Properly UseYour New Stroller
AVOID SERIOUS INJURY FROM FALLING OR SLIDING OUT.
USE THIS HARNESS AT ALL TIMES.
!WARNING!
Lock all foot brakes to keep stroller
from rolling.
Step 1. Place child in stroller.
Step 2. Hook shoulder straps to
waist belt.
Step 3. To secure,snap each side
of waist belt into buckle. (FigureA).
To release,press tabs and pull apart.
Step 4. For proper fit, adjust
shoulder straps and waist band as
shown.(Figure B). Adjust restraint system harness
1TO SECURE CHILD IN STROLLER:
2TO RECLINE SEAT (YOUR STROLLERWILL RECLINE IN 1 OF 2WAYS):
Step 1. To recline seat,loosen belt.
Step 2. To raise seat back,tighten belt.
Tighten
•TO AVOID FINGER ENTRAPMENT OR PINCHING,DO NOT ADJUST THE SEAT BACK WHILE CHILD IS IN THE STROLLER.
•TO AVOID HEAD ENTRAPMENT,ALWAYS FASTEN CANOPY TO SEAT BACK WHEN USING REAR SEAT IN RECLINED POSITION.
WARNING:
!
A
B
Step 1. Pull adjustment ring
down to recline seat back.
Step 2. Hold drawstrings down &
push adjustment ring up.
OR

7S45J-A-R3 2/03
Lock Front Swivel. Adjust front wheel so that wheel is straight
and lock is forward. Push lock to right.
Unlock Front Swivel. Push lock to left.
NOTE: On rough surfaces,lock the wheel to keep straight.On smooth
surfaces,unlock to allow the wheel to swivel.
4SWIVELWHEEL LOCK
(SELECT MODELS):
5AIR PUMP USE & STORAGE
To use the air pump
Step 1. Remove air pump from storage pocket on back stroller leg.
Step 2. Remove air tube from pump. (FigureA).
Step 3. Screw air tube to opposite end of pump. (Figure B).
Step 4.Attach air pump to fill-tube on tire.
Step 5. Pump air pump until tires are filled to 35 PSI (241 kPa).
Step 6. Disassemble pump and store in pocket when not in use.
AIRTUBE AIR PUMP
AIRTUBE
ATTACH
!CAUTION !
KEEP WHEELS AT A RECOMMENDED
TIRE PRESSURE OF 35 P.S.I. (241 KPA).
A
B
C
Step 1. Lock brakes.
Step 2. Recline seat.
Step 3. Close canopy.
Step 4. 4a Push red button to left with thumb to
unlock position 4b then squeeze large red lever on
handle to fold stroller.
NOTE: If 1-hand fold feature does not operate
properly,pull up latches on frame to fold.(Figure C).
Step 5. Push stroller down to fold stroller.
Step 6. Engage locking latch.(Figure D).
1-Hand Fold
4a
4b
6TO FOLD STROLLER:
D

8S45J-A-R3 2/03
• Always store your Jeep®baby product in a clean dry place. If exposed to damp conditions,leave fully opened and in a warm
environment. Dry off with a soft cloth. Storing a damp stroller will encourage mildew to form.
• Do not leave in the boot of a car.
• Avoid exposure to salt water/seat water,as this may encourage the formation of rust. If stroller is used in this environment,
completely clean your stroller afterwards to remove sand and salt from mechanisms and wheel assemblies.
•
Should parts of your stroller become stiff,squeak or difficult to operate ensure dirt is not the cause. To keep your stroller running
smoothly and avoid squeaking wheels use a silicone, graphite based lubricant or 3-in-1 oil (like motor oil). It is important to get the
lubricant into the axle and the wheel assembly. DO NOT over lubricate or useWD-40, as this will encourage the accumulation of dirt.
• Clean metal parts with a damp cloth and wipe dry.
• Clean woven fabric or vinyl parts with mild soap and water solution.
• Dry wet stroller with a soft cloth to prevent rusting.
• When storing stroller, never stack other items on top of it;this may damage the stroller.
• Periodically check for worn parts, loose screws,torn materials or stitching.
• Replace any damaged parts immediately.
CARE / MAINTENANCE
Jeep®is a registered trademark of DaimlerChrysler Corporation,and is used under license by Kolcraft®. © DaimlerChrysler Corporation 2003
KOLCRAFT
®
warrants this product to be free of defects in materials and workmanship, as follows: For a period of ONEYEAR from the date of purchase,
KOLCRAFT will repair or replace, at its option, the defective product.
REPAIR OR REPLACEMENTAS PROVIDED UNDERTHISWARRANTY ISTHE EXCLUSIVE REMEDY OFTHE CONSUMER. KOLCRAFT SHALL NOT BE LIABLE
FORANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OFANY EXPRESS OR IMPLIEDWARRANTY ONTHIS PRODUCT,EXCEPTTO
THE EXTENT REQUIRED BYAPPLICABLE LAW. ANY IMPLIEDWARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE ONTHIS
PRODUCT IS LIMITEDTOTHE DURATION OFTHISWARRANTY.
Some regions do not allow the exclusion or limitation of warranties set forth above, so the above exclusions may not apply to you. This warranty gives
you specific legal rights,and you may have other rights. We sincerely thank you for your purchase of this KOLCRAFT product.
For further information visit www.kolcraft.com
LIMITEDWARRANTY
To contact the manufacturer directly:
Kolcraft
®
Enterprises,Inc.Consumer Service Department
10832 NC Highway 211East
Aberdeen,NC 28315
1-800-453-7673 in U.S.& Canada, 1-910-944-9345 outside U.S.& Canada
Eastern StandardTime, 8 am-5 pm
MODEL NUMBER:
DATE OF MANUFACTURE:
DATE OF PURCHASE:
Once in a while, we are less than perfect and one of our products
reaches a customer with a problem. In most cases, we can solve your
problem with replacement parts. Please contact us before you return
one of our products to the store.Once a product is returned, it
cannot be resold. The materials and the energy used to make it are
wasted.
Please fill in the information in the space provided and attach a copy
of your purchase receipt.You will need this information to obtain
warranty service.
You can find the Model Number and Date of Manufacture on a
sticker located on the rear stroller leg.
PERSONAL RECORD CARD
SERVICE HOTLINE
Attention to manufacturing detail and strict quality control
ensures that this product meets the highest standards set by
Kolcraft Enterprises,Inc. If you encounter any problems or
need assistance please call our Customer Service /Warranty
Department.
Please direct any comments or questions to:
Born with Style
PO Box 789
Gladesville NSW 1675
Australia
Phone:[phone] or 02 9816 3837
Email:[e-mail]
Replacement parts provided by local distributor due to
accidental damage or misuse to product will be charged
accordingly.