Konami Concerto crescent User manual

P/N 810352 Rev B

Date of Publication: 4-3-18

Konami Gaming, Inc.

585 Konami Circle

Las Vegas, NV 89119-3720

Phone: (866) KGI-SLOT

Fax: (702) 361-9020

Operators Manual

Concerto Crescent

(Model: KGP 3.5 PDM2)

1-1

HISTORY

CONCERTO CRESCENT

(Original Instructions)

DOCUMENT REVISION HISTORY

EC REVISION DESCRIPTION OF CHANGE DATE APPROVED

7204 A RELEASE FOR PRODUCTION 12-22-16 KG

7775 B UPDATED THE FOLLOWING PART NUMBERS:

• 630004 TO 630088

• 810327

• 331405

• 331278

• 310644

• 331270

• 310667 TO 310859

• 331424

• 310785 TO 310959

4-3-18 EM

SECTION 1

Introduction

CUSTOMER SUPPORT�� 1-1

SHIPPING CHARGES�� 1-1

Warranty and RMA Process �� 1-1

Warranty Policy �� 1-1

RMA Process �� 1-1

RMA Tag �� 1-1

Radio Interference�� 1-2

Features: �� 1-2

Hardware Features �� 1-2

Hardware Options �� 1-2

Overview�� 1-3

Section 1 - Introduction �� 1-3

Section 2 - Set Up�� 1-3

Section 3 - Parts, Assemblies, & Hardware �� 1-3

Section 4 - Troubleshooting �� 1-3

Section 5 - Preventive Maintenance �� 1-3

Section 6 - Wiring Diagrams �� 1-3

Section 7 - Glossary & Index �� 1-3

Section 8 - Appendix �� 1-3

Terminology �� 1-3

Notices�� 1-3

Serial Number�� 1-4

Serial Number Plate �� 1-4

Using the Serial Number Plate�� 1-4

SECTION 2

Set-Up

Overview�� 2-1

Physical Specications�� 2-1

Cabinet Specications �� 2-1

Environmental Specications �� 2-1

Unpack and Inspect�� 2-1

Installing the Candle�� 2-2

Candle Pin Assignment�� 2-2

Stand Drill Guide �� 2-2

Drop Box Switch�� 2-2

Check Drop Switch Operations�� 2-2

Slot Accounting System�� 2-2

Overview �� 2-2

Connections �� 2-2

Fiber Optic Interface�� 2-3

Player Tracking Bracket�� 2-3

Removal�� 2-3

Installation�� 2-3

Main Deck Door �� 2-3

Sub Door�� 2-3

Bill Validator Door�� 2-4

Logic Unit Door �� 2-4

Display Door �� 2-4

Changing Locks�� 2-5

Lock Dimensions�� 2-5

Lock Cams �� 2-5

General Lock Instructions��2-5

Main Deck Door Lock��2-5

Sub Door Lock �� 2-6

Bill Validator Door Lock��2-7

Bill Acceptor (Factory Preset) �� 2-7

Collecting Bills��2-7

Player/Operator Interface ��2-7

CHANGE Button ��2-8

CASHOUT Button �� 2-8

SELECT NUMBER OF LINES Buttons�� 2-8

SELECT BET PER LINE Buttons�� 2-8

BET MAX Button ��2-8

SPIN Button ��2-8

Bill/Ticket Entry �� 2-8

Ticket Chute �� 2-8

43" LCD w/Touchscreen�� 2-8

Inspect the cabinet��2-8

Inspect the use environment��2-8

Inspect after connecting the AC plug to the recep-

tacle ��2-8

Turning On the Power Switch��2-8

KP3�5 Setup ��2-8

SECTION 3

Parts, Assemblies & Hardware

Functional Overview ��3-1

Required Tools �� 3-2

Commonly-Used Hardware��3-2

Switch Wiring��3-3

Logic Unit Switch��3-3

Removal��3-3

Installation��3-3

Main Deck Door Switch �� 3-3

Removal��3-3

Installation��3-3

Key Switch��3-3

Removal��3-3

Installation��3-3

Display Door Switch �� 3-4

Removal��3-4

Installation��3-4

Sub Door Switch��3-4

Removal��3-4

Installation��3-4

Bill Validator Switch Assembly�� 3-4

Removal��3-4

Installation��3-4

Power Supply ��3-5

Removal��3-5

Installation��3-5

Logic Unit��3-5

Removal��3-5

Installation��3-5

Main Processing Unit��3-5

Removal��3-5

TABLE OF CONTENTS

CONCERTO CRESCENT

(Original Instructions)

1-toc-i

Installation�� 3-5

Backplane Board �� 3-6

Removal�� 3-6

Installation�� 3-6

Speakers �� 3-6

Removal�� 3-6

Installation�� 3-6

Bill Validator�� 3-6

Removal�� 3-6

Installation�� 3-6

Belly Plex�� 3-7

Removal�� 3-7

Installation�� 3-7

Printer Assembly�� 3-7

Removal�� 3-7

Installation�� 3-7

Meter Assembly�� 3-7

Removal�� 3-7

Installation�� 3-7

Power Distribution Assembly�� 3-8

Removal�� 3-8

Installation�� 3-8

LCD Unit�� 3-8

Removal�� 3-8

Installation�� 3-8

P/N 810327 ASSY, MAIN MACHINE�� 3-9

P/N 310783 ASSY, DISPLAY DOOR �� 3-9

P/N 331405 ASSY, CAB, MAIN (Fig� 1 of 6) �� 3-10

P/N 331405 ASSY, CAB, MAIN (Fig� 2 of 6) ��3-11

P/N 331405 ASSY, CAB, MAIN (Fig� 3 of 6) �� 3-12

P/N 331405 ASSY, CAB, MAIN (Fig� 4 of 6) �� 3-13

P/N 331405 ASSY, CAB, MAIN (Fig� 5 of 6) �� 3-14

P/N 331405 ASSY, CAB, MAIN (Fig� 6 of 6) �� 3-15

P/N 331278 ASSY, DECK, MAIN �� 3-16

P/N 310644 ASSY, MAIN DECK AND FRAME �� 3-17

P/N 331276 ASSY, DR, SUB�� 3-17

P/N 310610 ASSY, PS �� 3-18

P/N 310612 ASSY, PNL, PWR CONT�� 3-19

P/N 310613 ASSY, PWR CONT PNL, INTL�� 3-20

P/N 331270 ASSY, HSG, CPU�� 3-21

P/N 310859 ASSY, KP 3�5 MAIN BOARD�� 3-21

P/N 331268 ASSY, ELP, RH ELBOW�� 3-22

P/N 331272 ASSY, SW, BV DR�� 3-22

P/N 331269 ASSY, ELP, LH ELBOW �� 3-22

P/N 331271 ASSY, HSG, BV�� 3-22

P/N 330920 ASSY, METER�� 3-23

P/N 331279 ASSY, BZL, BV/PTR�� 3-23

P/N 331328 ASSY, SW, JCM CASHBOX�� 3-24

P/N 310653 ASSY, LOGO, SUB DR �� 3-24

P/N 310959 ASSY, PNL, TOUCH DASH II �� 3-25

P/N 331310 ASSY, BTN PNL, 11 BTNS�� 3-25

P/N 331283 ASSY, BTN PNL, 16 BTNS �� 3-25

P/N 310642 ASSY, BTN PNL, 23”x1/3 LCD�� 3-25

P/N 310713 ASSY, TOPPER, TOVIS LCD�� 3-26

P/N 310645 ASSY, TOPPER, ELP�� 3-27

P/N 310375 ASSY, BV, JCM IVIZION, 1000 NOTE,

�� 3-28

72MM �� 3-28

P/N 310290 PRT, FUTURE LOGIC, GEN2, UNIVER-

SAL�� 3-28

GAME POWER CORD OPTIONS: �� 3-28

P/N 630007 ASSY, TOWER, TWO-TIER, CHROME

(Short) �� 3-28

P/N 630015 ASSY, TOWER, TWO-TIER, GOLD

(Tall) �� 3-28

P/N 630016 ASSY, TOWER, TWO-TIER, GOLD

(Short) �� 3-28

P/N 630025 ASSY, TOWER, THREE-TIER,

CHROME (Short) �� 3-28

P/N 630026 ASSY, TOWER, THREE-TIER, GOLD

(Short) �� 3-28

P/N 630088 ASSY, TOWER, TWO-TIER, CHROME

(Tall) �� 3-28

SECTION 4

Troubleshooting

Please refer to manual no� 810204 for Troubleshooting� 4-1

SECTION 5

Preventive Maintenance

Please refer to manual no� 810205 for Preventive Mainte-

nance�� 5-1

SECTION 6

Wiring Diagrams

Sheet 1 �� 6-2

Sheet 2 �� 6-3

Sheet 3a �� 6-4

Sheet 3b �� 6-5

Sheet 4 �� 6-6

SECTION 7

Glossary & Index

SECTION 8

Appendix

Overview�� 8-1

Electrical Components �� 8-1

Fuses �� 8-1

PCBs�� 8-1

Board Components �� 8-1

PCB, KP3�5, MPU�� 8-1

PCB, K3-IFB2, BACKPLANE�� 8-2

TABLE OF CONTENTS

CONCERTO CRESCENT

(Original Instructions)

1-toc-ii

SECTION 1 - INTRODUCTION

CONCERTO CRESCENT

(Original Instructions)

SECTION 1

Introduction

Document Part Number: 810352

Operators Manual

Concerto Crescent

(Model: KGP 3.5 PDM2)

This manual is subject to revision�

Konami Gaming, Inc. distributes all revisions�

Reproduction in whole or part of this manual by photographic,

electronic or any other form of recording is prohibited by law�

This manual may not be transmitted or copied for public or

private use without the express consent of Konami Gaming, Inc.

For permission write:

Konami Gaming, Inc.

585 Konami Circle,

Las Vegas, NV 89119-3270

Customer Service & RMA Information,

Installation & Field Service, call:

Phone: 866�KGI�SLOT

Fax: 702�361�9020

Domestic Sales, call:

Phone: 866�KGI�INFO

Fax: 702�952�1596

CUSTOMER SUPPORT

Konami Gaming, Inc is committed to offering the highest

quality 24 hour, seven (7) day a week, technical support� For

Service calls:

Phone: 1�866�KGI�SLOT

E-Mail: customerservice@konamigaming�com

All calls are logged into a database to track response times,

the nature of the calls, and developing trends�

SHIPPING CHARGES

• Konami Gaming, Inc� pays for standard ground shipping

on warranty items only�

• The Operator is responsible for shipping charges on

expedited delivery or non-warranty items�

WARRANTY AND RMA PROCESS

Warranty Policy

Warranty: 90 days parts and labor from date of sale�

rMa Process

• RMA tags are included in the spare parts kit.

• RMA numbers are issued by calling the Customer Support Hotline

at 1.866.KGI.SLOT.

• Parts returned to Konami Gaming, Inc. will only be accepted with

an RMA number. Please do NOT send any parts back without an

RMA number.

• Once a replacement part is issued, the Operator has 30 days to return

the old part without being charged. If the old part is not returned within

30 days, the Operator will be charged the full retail price for the item.

RMA TAg

NOTE:RMAtags are used to repair damaged equipment to

its original state of operation. Completely filling out the RMA

is required.

(RMA) CASE #

MACHINE SERIAL #

CASINO

PART #

PART SERIAL #

PART DESCRIPTION

PROBLEM

JURISDICTION

WHITE - FIELD ENG. YELLOW - SHIPPING MANILA - PART

TECHNICIAN NAME

SERVICE

PARTICIPATION WARRANTY CUSTOMER CAUSED

TRIAL CONTRACT MAINTENANCE

SECTION 1 - INTRODUCTION

CONCERTO CRESCENT

(Original Instructions)

FEATURES:

HardWare Features

• 43” UHD Graphics

• Crisper graphics, high resolution

• Hardware included provides touch screen functionality

• Ergonomically designed Button Panel

• Logical button layout

HardWare oPtions

Bill Acceptors

• Cash Code

• IVizion

• JCM UBA 10 Standard

• JCM UBA 10 ICB

• JCM UBA 11 Standard

• JCM UBA 11 ICB

• Mars SC6607

• Mars Cashow w/EZ Trax

• Mars SC8307

• Mars SCM6607YE, 1000 Note

Printers

• Future Logic Gen 2

• Ithaca 950

• Paycheck 3

RADIO INTERFERENCE

This device complies with part 15 of the FCC Rules� Operation

is subject to the following two conditions: This device may NOT

cause harmful interference and this device must accept any

interference received including interference that may cause

undesired operation� Improper installation or maintenance

may result in radio interference�

SECTION 1 - INTRODUCTION

CONCERTO CRESCENT

(Original Instructions)

OVERVIEW

This manual is for operators, technicians and Konami Gaming

service personnel� It provides useful information to aid in the

set up, operation and maintenance of the Konami Gaming,

Inc� Concerto machine� It provides required information such

as an introduction to the equipment, operation, handling

errors, troubleshooting tables and maintenance� This manual

describes the following items:

section 1 - introduction

Section 1 contains general machine information, contact

information, a description of manual content, and a general

list of features�

section 2 - set uP

Section 2 contains installation and set up information for use

in installing and conguring a machine in the eld.

section 3 - Parts, asseMblies, & HardWare

Section 3 describes machine components, the removal and

installation of these components, and an illustrated parts

manual�

section 4 - troublesHooting

Section 4 identies the troubleshooting manual necessary to

diagnose and repair errors or malfunctions�

section 5 - Preventive Maintenance

Section 5 identies the maintenance manual required to keep

the machine error free and performing as designed�

section 6 - Wiring diagraMs

Section 6 contains the overall system wiring diagram for the

components in the machine�

section 7 - glossary & index

Section 7 contains reference to technical terminology used

in this document�

section 8 - aPPendix

Section 8 contains consumable parts lists�

TERMINOLOGY

The term “Machine” is used throughout this manual and is

dened as a physical piece of electromechanical equipment

designed and manufactured by Konami Gaming, Inc� This

equipment is only for sale and use as an amusement

apparatus in jurisdictions permitting such devices�

The term “Game” is used throughout this manual and is dened

as the programmed operation of the machine after money,

tokens, coupons, or equivalent are accepted� Typical game

characteristics include player interaction with the machine

through the use of buttons, and payout of coins, tokens,

coupons, or equivalent when reel symbol combinations appear

on the payline and match the game’s paytable�

The term “Operator” is used throughout this manual and is

dened as any person, partnership, company, or corporation,

and/or their legal representatives, who own, operate, service,

maintain, and/or derive prot from their association with this

machine�

The term “Player” is used throughout this manual and is

dened as any person who deposits money, tokens, coupons,

or equivalent into the machine for the purpose of playing the

games offered by the machine as dened by the rules and

odds set by the machine’s operator�

NOTICES

This document contains the following important notes:

This symbol indicates a CAUTION or WARNING. These

indicate actions or situations that can be damaging or

dangerous to you or your equipment. Read and observe

all cautions and warnings.

This symbol indicates a NOTEor TIP. Notes and tips

are items of special interest pertaining to the section or

procedure you are reading about. They typically augment

or clarify the material.

SECTION 1 - INTRODUCTION

CONCERTO CRESCENT

(Original Instructions)

SERIAL NUMBER

All requests for service or RMA replacement require the

machine serial number, located on the lower front right side

of the cabinet� See the illustration below for location of the

Serial Number Plate�

Check the serial number using the Serial Number Plate or

the stamped or engraved serial number�

serial nuMber Plate

The information displayed on the Serial Number Plate

includes:

• MODEL NO�: Model number designation�

• MANUFACTURE DATE: Date of manufacture�

• SERIAL NUMBER: Cabinet-specic number.

• VAC, HZ, A: Usage environment for the cabinet�

585 Konami Circle, Las Vegas, NV, USA 89119

120 V~ 5A 50/60Hz

KGP 3.5 PDM2

MODEL NO.

SERIAL NO.

P/N 192919A

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

using tHe serial nuMber Plate

The Serial Number Plate is installed on the outside of the

Main Cabinet, on the right side�

reFerring totHe engraved serial nuMber

The serial number is stamped or engraved on the front

inside of the cabinet� This serial number is identical with the

serial number found on the Serial Number Plate. If you nd

a different serial number, contact your KGI representative

immediately�

Serial

Plate

Stamped

Serial Plate

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

SECTION 2

Set-Up

OVERVIEW

Section 2, Set-Up, describes the installation and set-up of the

machine� This section covers the following topics:

• Physical Specications

• Environmental Specications

• Unpacking and Inspecting

• Candle (Signal Tower) Installation

• Drop Box Door Switch

• Slot Accounting System

• Opening and Closing Doors

• Lock Installation

• Bill Validator Options

• Startup

Width

Height

(Cabinet)

Depth

(at Door)

Depth

PHYSICAL SPECIFICATIONS

cabinet sPeciFications

• Height (±0�15") 67�35" 171�0cm

• Depth (at Door) (±0�15") 25�85" 65�7cm

• Depth (Cabinet) (±0�15") 15�60" 39�6cm

• Width (Cabinet) (±0�15") 27�00" 68�6cm

• Weight (±5 lb) 284�0 lbs 128�8kg

ENVIRONMENTAL SPECIFICATIONS

Line Voltage Input: 100–240 VAC, 50 or 60 Hz�

The following calculations are based on an input voltage of

120 VAC:

• Power supply input voltage 110 VAC: 108–120 VAC

(nominal 120 VAC) at 50/60 Hz�

• Power supply output voltage: +12 VDC, +24 VDC�

• Current draw at rest: 1�83 A (220 W)�

• Current draw during game play: 1�9 A (228 W)�

• Maximum operating ambient temperature: 104°F (40°C)�

• Minimum operating ambient temperature: 32°F (0°C)�

• Maximum surface ambient temperature: 105°F (41�5°C)�

• Minimum surface ambient temperature: 32°F (0°C)�

• Maximum relative humidity: 95% (non-condensing)�

UNPACK AND INSPECT

Unpack and inspect the machine before power is turned on�

If the machine has been damaged during shipping, contact

your Konami Distributor, or Konami Customer Service

Representative, depending on warranty and sales contract

terms�

For Return Merchandise Authorization (RMA) information,

see Section 1 of this manual�

Carefully unpack and remove all loose parts and shipping

materials� Inspect components for damage� Verify the power

cord is properly routed out of the cabinet� Verify all wire

connectors are rmly seated. Check all display areas for signs

of broken glass or bulbs�

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

INSTALLING THE CANDLE

1� Open the Main Deck Door and remove Display Door�

2� Pass Candle Connector through the hole in the top of

the machine�

3� Mount the Candle with two UNC 8-32 nuts�

4� If equipped, secure frame ground (FG) wire of Candle

with one of the 8-32 nuts�

5� Install and lock Display Door, and close and lock Main

Deck Door�

6� Turn power on and verify that Candle illuminates�

candle Pin assignMent

CANDLE PIN ASSIGNMENT

PIN NUMBER WIRE COLOR SIGNAL

ASSIGNED LIGHT LOCATION

1 BROWN TL0 BOTTOM

2 BLUE TL1 TOP

3 VIOLET TL2

4 GREY TL3 RESERVED

5 N� C� N� C�

6 YELLOW +24 V

STAND DRILL GUIDE

15.949 2X 18.728

2X 8.8282X 1.806 2.50

1.648

7.334

1.580

2.160

3X

4.074

15.60

3X

8.500 4X R.12

15.494 23.88 6X .375

DROP BOX SWITCH

1� Open the Main Deck Door�

2� Locate the connector labeled DROP (on the main cabinet

harness)�

3� Connect the optional Drop Switch Harness (P/N 110324)�

4� Connect the three spade connectors to the Drop Switch�

NOTE: To ensure proper spacing between machines, the

minimum allowable width of the stand a Konami machine

can be mounted on is 28”.

NOTE: The Drop Box Switch wiring is typically used

ONLY when the machine is not connected to a slot

accounting system.

cHeck droP sWitcH oPerations

If any of the following problems arise after turning the power

on, check that the Drop Box Switch is installed properly�

• The 031 DROP DOOR ACCESSED error message is not

displayed even after the power is turned on again with

the drop-door closed�

• The 041 DROP DOOR PORT error message is displayed�

• No error messages appear when the Sub-Door is opened

and closed�

A Drop Door open accessed error can be detected even with

the power turned off� Reset the error and turn the power on

to check that the switch is installed correctly�

DROP BOX SWITCH PIN ASSIGNMENT

PIN # PIN ASSIGNMENT DESCRIPTION

1 GND GND (COM)

2 SW_DROP SECURITY

(SW DROP BOX DOOR (N�O�))

3 BSW_DROP SECURITY

(SW DROP BOX DOOR (N�C�))

4 N� C� -

SLOT ACCOUNTING SYSTEM

overvieW

The Slot Accounting System (SAS) communication with the

video gaming machine takes place via interface connectors

located on the Backplane board in the Logic Unit box and

settings in the Konami Maintenance System (KMS)�

connections

Under typical conditions, CNB35/Port 1 on the backplane, is for

interconnection to the SAS Unit, used for ber optic interface.

CNB36 and CNB37 are used for serial communications with

conventional wiring�

CNB35

(COM1)

CNB36

(COM2)

CNB37

(COM3)

The Concerto Crescent is a well-balanced machine,

however, make sure to use four screws when mounting

the machine onto a Stand.

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

FIBER OPTIC INTERFACE

When ber optic communication lines are used, they are rst

routed to the SAS Unit mounted in the machine� The SAS

Unit is equipped with two input and two output ber optic

receptacles� The SAS unit is also equipped with a serial input/

output connector and attached wiring, the output of which is

connected to the CNB35 port on the Backplane board�

SERIAL

I/O

AC115V IN

Green : Communication

Blink Lit Off

Normal

Error Idling

Normal

Error Idling

Normal

Error Idling

Red : Opto IN2 Monitor

Yellow : Terminal Serial Data

SERIAL

I/O

OUT1 OUT2 IN1 IN2

SERIAL I/O

FIBER OPTIC OUT 1

FIBER OPTIC OUT 2

FIBER OPTIC IN 2

FIBER OPTIC IN 1

AC 115V IN

PLAYER TRACKING BRACKET

The SAS components are mounted on a removable bracket

installed on top of the box�

reMoval

1� Open the Main Door and turn power off�

2� Open main deck door�

3� Remove four 8-32 X 1/4 screws holding player tracking

panel�

4� Remove player tracking panel from main deck door�

installation

1� Install player tracking panel onto main deck door�

2� Secure with four screws�

Player Tracking

Panel

OPENING AND CLOSING THE DOORS

Main deck door

1� To open main deck door, insert main deck door key into

key cylinder underneath main deck�

2� Turn key 90° clockwise�

3� Pull latch button with key turned�

4� Open main deck door�

Lock

Latch

5� Close main deck door with the key turned clockwise�

6� Turn key 90° counter-clockwise and remove key from

cylinder�

sub door

1� To open the sub door, insert key into cylinder on the right

side of cabinet�

2� Turn key 90° clockwise, and press sub door lever�

3� Pull door open�

4� Push main door closed and turn key 90° counter-

clockwise� Remove key from cylinder�

Sub Door

Lever

Key Cylinder

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

bill validator door

1� To open the Bill Validator Door, insert the key into the

cylinder on the Bill Stacker Door�

2� Turn the key 90° counter-clockwise�

3� Open the Bill Stacker Door�

4� To close the Bill Validator Door, close the Bill Stacker Door�

5� Turn the key 90° clockwise�

6� Remove the Bill Stacker Door key from the cylinder�

logic unit door

The following describes how to open and close the Logic Unit

Door with the Main Door open�

1� To open the Logic Unit Door, insert the Logic Unit door

key into the cylinder on the front of the Logic Unit�

2� Turn the key 90° counter-clockwise�

3� Open the Logic Unit door by pulling the logic door toward

you and up to clear the mounting tabs�

4� To close the Logic Unit Door, insert the Logic Unit door

tabs into the slots and pivot into the locking position�

5� Turn the logic door key 90° clockwise�

6� Remove the Logic Unit Door key from the cylinder�

disPlay door

WARNING:When servicing or replacing the Crescent LCD unit,

two people are required to lift the unit to prevent injury

or damage.

1� To remove display door, open main deck door (see above)

and press display door latch to unlatch�

2� Close main deck door and remove display door�

3� Install display door on frame�

4� Open main deck door and secure latch�

5� Close and lock main deck door�

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

CHANGING LOCKS

lock diMensions

The following shows the standard lock dimensions�

.87

.68 .39

.73

.62

1.28

.58

(ALL DIMENSIONS ARE IN INCHES)

lock HardWare

The following shows the standard lock hardware�

lock caMs

The following shows the standard lock cams required for this

machine�

CAM, LOCK,

LOGIC UNIT

DOOR

CAM, DOOR,

BV

CAM, LOCK,

MAIN DECK

190020

192688

192744

LOCKING CAMS

PART # DESCRIPTION

190048 CAM, DOOR,

BV (CASHBOX)

NOTE: Locks are supplied for shipping purposes only.

It is recommended that all locks be replaced with owner/

operator approved and secured locks.

GENERAL LOCK INSTRUCTIONS

1� Remove 9/32-28 UNF Nut and Cam from Shaft�

2� Remove 3/4-28 UNF Nut from Lock�

3� Remove Key Cylinder�

4� Install new Key Cylinder�

5� Secure with 3/4-28 UNF Nut�

6� Install Cam and 9/32-28 UNF Nut on Shaft�

Main deck door lock

1� Open Main Deck Door�

2� Replace Lock�

3� Turn key 90° clockwise to open Main Deck Door�

4� Return Door to the original position�

5� Make sure that the Lock is installed properly by locking

and unlocking the Door�

If any of the following problems arise before turning on the

power, check that the above procedure was performed

properly�

• The door will not open and close easily�

• The door release does not engage easily�

• The key cannot be removed or turned�

If the MAIN DOOR OPEN message appears after turning the

power on, check that the above procedure was performed

properly� The probable causes of the error are:

• The lock is not installed properly�

• The sub door switch is not depressed completely�

If the MAIN DOOR ACCESSED message appears after

turning the power on, turn the Reset key switch�

Go to DIAGNOSTIC DOOR in the KMS Diagnostics to check

Main Door switch�

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

logic unit door lock

1� Open Main Deck Door�

2� Open Logic Unit Door�

3� Replace Lock�

4� Turn the key 90° counter-clockwise to open the Logic Unit

Door, then return it to the original position�

5� Make sure that the Lock is installed properly by locking

and unlocking the Door�

If any of the following problems exist before turning on the

power, check that the key works properly for the installed lock�

• The door will not open and close easily�

• The key cannot be removed or turned�

If the 012 LOGIC DOOR OPEN message appears after turning

on the power, check that the above procedure was performed

properly� The probable causes of the error are:

• The lock is not installed properly�

• The logic door switch is not depressed completely�

If the 032 LOGIC DOOR ACCESSED message appears after

turning on the power, turn the reset key switch�

Go to DIAGNOSTIC DOOR in the KMS Diagnostics to check

the logic door switch�

sub door lock

1� Open Sub Door�

2� Replace Lock�

3� Turn key 90° to open Main Door then return it to the

original position�

4� Make sure that the Lock is installed properly by locking

and unlocking the Door�

If any of the following problems exist before turning the power

on, check that the key works properly for the installed lock�

• The Door will not open or close easily�

• The Latch does not engage easily�

• The key cannot be removed or turned�

If the SUB DOOR OPEN message appears after turning the

power on, make sure that the above procedure was performed

properly� The probable causes of the error are:

• The lock is not installed properly�

• The Main Door Switch is not depressed completely�

If the SUB DOOR ACCESSED message appears after turning

the power on, turn the reset key switch�

Go to DIAGNOSTIC DOOR in the KMS Diagnostics to check

sub door switch and sensor�

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

bill validator door lock

1� Open Main Door�

2� Open Bill Validator Door�

3� Replace Lock�

4� Turn key 90° counter-clockwise to open the Bill Validator

Door, then return it to the original position�

5� Make sure that the Lock is installed properly by locking

and unlocking the Door�

If any of the following problems arise before turning the power

on, check that the above procedure was performed properly�

• The Door will not open and close easily�

• The key cannot be removed or turned�

If the 014 BILL DOOR OPEN message appears after turning

on the power, check that the above procedure was performed

properly� The probable causes of the error are:

• The Lock is not installed properly�

• The Bill Validator Door Switch is not depressed completely�

If the 034 BILL DOOR ACCESSED message appears after

turning the power on, turn the Reset key switch�

Go to DIAGNOSTIC DOOR in the KMS Diagnostics to check

the bill box door switch�

BILL ACCEPTOR (FACTORY PRESET)

The bill acceptor validates, either accepting or rejecting bills

inserted into the bill validator module (bill head)�

Accepted bills are transported to the cash cassette, and an

appropriate number of credits register on the credit meter� For

example, an accepted U�S� $1�00 bill shows as four credits

on a 25¢ machine� Rejected bills are returned to the player�

• Remove the bill validator module (refer to the Section

3 - Assemblies, Parts & Hardware)�

NOTE: Remove the spacer for a short lock. Retain the

spacer and other small parts for future use if not required

for this application.

collecting bills

When the Bill Stacker is full, the BILL STACKER FULL

message appears� This suspends the game until the bills

are collected� Please note that Bills should be collected

periodically before the Bill Stacker becomes full�

1� Open the Sub Door�

2� Open the Bill Stacker Door�

3� Pull out the Bill Stacker�

4� Unlock the locks (two (2) places) on the back of the Bill

Stacker at the same time and remove the bills�

5� Install the Bill Stacker in the Bill Validator unit�

6� Close the Bill Stacker Door and Sub Door�

7� Turn the Reset key-switch to recover from the error�

PLAYER/OPERATOR INTERFACE

The following illustration identifies the Player/Operator

interface items used to play the game�

Bill Entry

Ticket

Chute

Speaker

LCD Player

Tracking

Panel

Select Number of Lines

Buttons (Top Row)

Spin

Button

Select Bet Per Line

Buttons (Bottom Row)

Speaker

Flat Panel

Button Panel

SECTION 2 - SET-UP

CONCERTO CRESCENT

(Original Instructions)

cHange button

The CHANGE button is used to illuminate the upper Signal

Tower light with a steady ash, indicating to the Operator that

change is required at the Machine�

casHout button

The CASHOUT button is used by the Player to retrieve unused

credits from the Machine� When pressed, the Hopper activates

dropping coins into the coin bowl, triggering an attendant pay,

printing a ticket or a combination of events�

select nuMber oF lines buttons

The SELECT LINE(s) button allows the player to choose the

number of lines played�

select bet Per line buttons

The BET X PER LINE buttons allow the player to select the

number of credits played for each of the selected lines�

bet Max button

The BET MAX button wagers the maximum number of

credits for each time it is pressed� A credit equals the

current denomination X 1 (if the machine is optioned with a

denomination of 50¢, and the maximum number of coins is

45, the bet max value would be $22�50)� When the BET MAX

button is pressed, the reels spin automatically�

SPIN button

The SPIN button can act as a REPEAT BET button� After

the number of lines are selected, the credits wagered per

line activates the game� The SPIN button then activates the

next game�

bill/ticket entry

Accepts paper currency and converts it into credits according

to the denomination of the machine� If a $20�00 bill is inserted,

and the denomination of the machine is 5¢, 400 credits will

be added to the credit meter�

ticket cHute

The ticket printer is used to dispense tickets that reect the

amount of credits remaining on the machine that can be

cashed for their monetary value, or in some cases, can be

inserted into another machine to add credits and enable play�

43" lcd W/toucHscreen

The LCD screen is used to display animations, bonus games

and bonus pays to the player� It is also used to access the

KMS to display game information, audit information, log les,

game recall les, event info les and system info les. It is also

used to display diagnostic screens and game test screens�

STARTUP

Check the following items before connecting the AC plug of

the machine to a receptacle�

insPect tHe cabinet

• Check that all the units are plugged in rmly.

• Check that all the connectors are connected�

• Check that the AC cord is not damaged�

• Check that the Power Switch is to the OFF position�

• Check that fuses are not opened�

insPect tHe use environMent

• Check that the power supply meets the specication for

the cabinet�

• Check that the AC cord is not strained (do not bend the AC

cord at a sharp angle, coil it or put a heavy weight on it)�

• Check that there is nothing containing water near the

power supply�

insPect aFter connecting tHe ac Plug to tHe

recePtacle

• Check that the smell of smoke is not present�

• Check that no sparks, smoke or ame are produced.

• Check that the AC cord does not get too hot�

TURNING ON THE POWER SWITCH

The rst time the game is started a RAM CLEAR procedure

is required� Refer to 810239 - KP3�5 Setup Manual

KP3.5 SETUP

Refer to 810239 - KP3�5 Setup Manual - to properly set up

game�

SECTION 3 - PARTS, ASSEMBLIES & HARDWARE

CONCERTO CRESCENT

(Original Instructions)

SECTION 3

Parts, Assemblies & Hardware

LCD

LED Light

Panel

Subwoofer

(located

behind LCD)

Speakers

(located on

deck door)

Player Tracking

Panel (located

on main deck

door)

Bill Validator

Access Door

Power Supply

Main Power

Switch (located

on power supply)

Logic Unit

Housing

Printer

CAUTION: PCB’s may contain a lithium battery.

Danger of explosion if the battery is incorrectly

replaced. Replace only w ith the same, o r

equivalent type recommended by the manufacturer.

WARNING:Power to the machine must be turned off prior

to cleaning the inside of the machine or removing any

mechanical or electrical assembly. Unplug the machine.

WARNING: Hazardous high voltage exists within the

cabinet even with machine power off and the power

cord unplugged! Use extreme caution when removing

electrical assemblies to avoid injury. Discharge body

static BEFORE touching PCBs to avoid damaging

electrostatic sensitive components. Only qualified

personnel should attempt servicing this machine.

CAUTION: Distributors, Operators, and Users are

not to modify the equipment for any other use. Konami

Gaming, Inc. cannot be held liable for damages or injuries

resulting from use or modiﬁcation of this equipment.

Konami Gaming, Inc. cannot be held liable for damages or

injuries arising from improper or unsupervised installation,

modiﬁcation, or use of equipment not manufactured or

approved by Konami Gaming, Inc. This equipment is

designed as a gaming device for amusement only, for sale

and use in jurisdictions permitting such devices.

FUNCTIONAL OVERVIEW

This chapter describes names and functions of the main parts� The following illustrations below to identify the major

components�

Tower Light

Hard Meters

LCD Edge

Light Panels

Bill Entry

Ticket Chute

Sub/Belly Door Logo

Button Panel

Sub Door Lock

Serial Plate

Main Door Lock

Elbow Light

Speakers

SECTION 3 - PARTS, ASSEMBLIES & HARDWARE

CONCERTO CRESCENT

(Original Instructions)

MAINTENANCE OVERVIEW

Section 3, Parts, Assemblies & Hardware, describes part

removal and installation and includes a parts manual� This

manual is intended for experienced maintenance personnel

working on gaming machines�

• Removal: Describes how to remove components from the

cabinet� Note that you may need special tools depending

on the type of component removed�

• Disassembly: Describes how to disassemble the

components removed from the cabinet into parts on which

maintenance can be performed�

• Assembly: Describes how to assemble the parts� Use

caution when reconnecting harnesses to ensure proper

operation� Incorrect assembly may cause malfunctions

or failures�

• Installation: Describes how to install the components

in the cabinet�

required tools

• Phillips Screwdriver (No� 1 and No� 2)

• Small Phillips Screwdrivers (No� 0 and No� 1)

• 4 to 13 mm Nut Driver or Ratchet Wrench

• 4 to 13 mm Wrench Set

• 22 to 24 mm Double-end Wrench

• Hand Riveter

• Needle Nose Pliers

• Pliers

• Voltage and Amperage Tester

• Crimping Tool for Connectors

• Plastic Ties

• Wire Stripper

• Pin Extractor

• IC Extractor

• Wire Cutters

coMMonly-used HardWare

The following table shows the hardware that this machine

uses� Using incorrect hardware may damage the equipment�

PART

NO. DESCRIPTION

450013 NUT, HEX KEP #10-32

450014 NUT, HEX KEP #4-40

450015 NUT, HEX KEP #6-32

450016 NUT, HEX, KEP #8-32

450018 NUT, HEX, KEP M4

450107 SCREW, SEMS, PAN HEAD PHILLIPS, #4-40 X 1/4

450108 SCREW, SEMS, PAN HEAD PHILLIPS, #4-40 X 3/8

450109 SCREW, SEMS, PAN HEAD PHILLIPS, #6-32 X 1/2

450110 SCREW, SEMS, PAN HEAD PHILLIPS, #6-32 X 1/4

450114 NUT, HEX, KEP #4-40

450115 SCREW, SEMS, PAN HEAD PHILLIPS, #8-32 X 1/4

450122 SCREW, SEMS, PAN HEAD PHILLIPS, M3 X 6

450123 SCREW, SEMS, PAN HEAD PHILLIPS, M3 X 8

450127 SCREW, SEMS, PAN HEAD PHILLIPS, M46

450144 NUT, NYLOK, #2-56

450146 GUIDE, PCB, 6”

450160 SPRING, EXTENSION, �25 DIA X 1 LONG

450161 SCREW, CONNECTOR MOUNTING

450163 RIVET, POP, 1/8 DIA X 3/8 LONG

450167 SCREW, PAN HEAD PHILLIPS, M3 X 12

450176 WASHER, #8 FLAT

450185 STAY, DOOR, 10�5”

450282 NUT, HEX, NYLOCK, #8-32

450285 WASHER, FENDER, #10, OD 1 X 7/32, ID 3/64

450366 NUT, HEX, #2-56

450410 CABLE TIE, 4”

450420 SCREW, TPG, HEX WSHR HD, #4-40 X �250

450428 SCREW, TPG, HEX WSHR HD, #8-32 X �250

450430 SCREW, TPG, HEX WSHR HD, #8-32 X �375

450513 SPCR, NYLON, �38 OD X �17 ID X �25L

450546 BUMPER, THRU-HOLE, W/WASHER

450573 GAS SPRING

450575 WASHER, �75 OD X �32 ID X �07 THK

450576 SPRING

450577 STANDOFF, HEX, F-F, 8-32 X 7/8” LG

450581 LATCH, DRAW, SPRING TENSION

450587 RING, RTNG, EXT, E-STYLE, 1/2 SHAFT

450588 HINGE, CONCEALED, 90DEG� OPENING

450589 SCREW, TPG, HEX WSHR HD, #10-32 X �375

450590 SCREW, TRUSS, HD, PHIL, #8-32 X �375, BLACK OXIDE

450596 SPACER, #8, �375 OD X �281 LG, NYLON, OFF-WHITE

450597 PLUG, HOLE, �625 DIA X �016-�125 PNL THKNS, BLK

450598 STUD, 8-32 X 1�25 w/ SLOT

450601 DAMPER, �235 LG X 76 STROKE, W/END FTG

450603 SCREW, TPG, PH PHIL, #8-32 X 1/4

450604 MAGNET, ADHESIVE BACKED, �25DIA X �10 THK

SECTION 3 - PARTS, ASSEMBLIES & HARDWARE

CONCERTO CRESCENT

(Original Instructions)

SWITCH WIRING

Each wire of the switch harnesses is marked to indicate

terminal position� Use the following illustration to ensure the

switch is connected correctly�

DOOR SWITCH WIRE LOCATIONS

LOCATION MARK

Terminal 2 COM

Terminal 4 N�C�

Terminal 6 N�O�

LOGIC UNIT SWITCH

reMoval

1� Disconnect harness from Switch�

2� Remove two #2-56 nuts from Switch Assembly�

3� Remove Switch�

installation

1� Install Switch on mounting studs and secure with two

#2-56 nuts�

2� Connect harness�

MAIN DECK DOOR SWITCH

reMoval

1� Unlock and open Main Deck Door�

2� Remove any components necessary to allow access to

Switch�

3� Note wire locations for installation and remove all wires

from Switch�

4� Grasp the two tabs on the Switch and push upward to

remove bracket�

installation

1� Push new Switch into mounting bracket until two tabs on

the Switch seat in place�

2� Connect wires to terminals�

3� Re-install removed components�

4� Close and lock Main Deck Door�

KEY SWITCH

reMoval

1� Turn off machine power�

2� Unlock and open Main Deck Door�

3� Disconnect wires from Switches�

4� Remove 3/4” nut and remove Switch from machine�

installation

1� Insert Switch into machine and install 3/4” nut�

2� Connect wires to terminals�

3� Turn on main power�

4� Close and lock Main Deck Door�

SECTION 3 - PARTS, ASSEMBLIES & HARDWARE

CONCERTO CRESCENT

(Original Instructions)

DISPLAY DOOR SWITCH

reMoval

1� Unlock and open Deck Door�

2� Unlatch Display Door and remove door to access Switch�

3� Note wire locations for installation and remove wires

from back of Switch�

4� Grasp the Display Door Switch from the top and bottom

behind the mounting bracket and push Switch forward�

installation

1� Insert switch from the front of machine�

2� Gently push switch into the bracket until it seats�

3� Connect wires to terminals�

4� Install and latch display door�

5� Turn on machine power�

6� Close and lock deck door�

SUB DOOR SWITCH

reMoval

1� Unlock and open Sub Door�

2� Note wire locations for installation and remove all wires

from Switch�

3� Gently grasp Sub Door Switch from the top and bottom

behind the mounting bracket and push the Switch forward�

installation

1� Insert Switch from the front of the machine�

2� Gently push Switch into the bracket until it seats�

3� Connect wires to the terminals�

4� Turn on machine power�

5� Close and lock Sub Door�

BILL VALIDATOR SWITCH ASSEMBLY

reMoval

1� Unlock and open Sub Door and Main Deck Door�

2� Turn off machine power�

3� Open Bill Validator Door and remove Stacker�

4� Remove Bill Validator�

5� Disconnect harnesses from Bill Validator Door Switch

Assembly�

6� Remove two #8-32 nuts and Bill Validator Door Switch

Assembly�

installation

1� Install Bill Validator Door Switch Assembly and secure

with two #8-32 nuts�

2� Connect harnesses to Bill Validator Door Switch Assembly�

3� Install Bill Validator�

4� Turn on machine power�

5� Close and lock Main Deck Door and Sub Door�

Konami Concerto Crescent User manual

Popular Arcade Game Machine manuals by other brands