Konami Solar Assault User manual

46
Thank you for purchasing this Konami product. This manual explains how to operate your
game machine correctly and safely.
About this product

•Failure to operate the machine correctly could result in malfunction or
accidents, so please read this manual carefully before commencing
operation. Be sure to operate the machine as described in this manual.
•Keep this manual carefully so as to be ready for use when necessary.
•If the machine still fails to display or to get started, immediately turn OFF
the power switch and contact your nearest dealer.
This manual covers the following models:
•GN672-UC •GM672-UC
The specifications of GN672-UC may be somewhat different from GM672-UC. In such a
case, read the descriptions of the model which applies to the game machine you are
operating.
•The specifications of this product are subject to change without notice for
reasons such as improving the performance.
•The contents of this game, its main data and design are protected by copyright
law and industrial property law.
•Unauthorized reproduction of this document or any of its contents is strictly
forbidden.
© 1997 KONAMIALL RIGHTS RESERVED.

47
Contents
1
Precautions for use………………………………………………………… 2
1 Specifications ……………………………………………………………… 8
2 Names of parts and list of main parts…………………………………… 10
3 How to play ………………………………………………………………… 14
4 Opening and closing the doors
4-1 Opening and closing the maintenance door …………………………… 16
4-2 Opening and closing the coin door……………………………………… 17
5 PCB settings
5-1 PCB start-up check (self test)…………………………………………… 18
5-2 Adjusting the game environment (manual test) ……………………… 19
5-3 Mode descriptions ……………………………………………………… 20
6 Setting up the game machine
6-1 Connecting the unit (GN672-UC only) ………………………………… 24
6-2 Fastening the adjusters ………………………………………………… 25
6-3 AC bracket………………………………………………………………… 26
6-4 Service panel …………………………………………………………… 27
6-5 Separating and moving the units ……………………………………… 28
6-6 Moving the coin counter ………………………………………………… 30
7 Maintenance and annex
7-1 Replacing the coin selector …………………………………………… 33
7-2 Replacing the fuse ……………………………………………………… 33
7-3 Replacing the fluorescent light ………………………………………… 34
7-4 Replacing the control lever unit………………………………………… 36
7-5 Replacing the press-button …………………………………………… 38
7-6 Adjusting the projector and monitor …………………………………… 40

2
In this manual, the precautions to be followed without fail in order to prevent damage to
persons to install, use or maintain “SOLARASSAULTTM” or other persons or to properties are
shown as follows.
2
Precautions for use
Be sure to read the following
•The following suggestions show the degree of danger and damage caused when the
product is used improperly with the suggestions disregarded.
•The following graphic suggestions describe the types of precautions to be followed.
Indicates a matter of which care should be taken.
Indicates a matter which is forbidden.
Indicates a matter which should be performed
without fail.
2
CAUTION Indicates a situation where disregarding the suggestions could result in injury or product
damage.
WARNING Indicates a situation where disregarding the suggestions could result in death or serious
injury.

3
Setting Up
•Be sure to consult your nearest dealer when setting up, moving or transporting this product.
·This product should not be set up, moved or transported by anyone other than industry specialists.
Doing so could result in injury or product damage.
·When installing the machine, be sure to place 10 level adjusters (6 adjusters for GM672-UC) securely on
the floor and make sure that the machine is stable at a level. If the machine is unstable, it could result
in injury or accidents.
·When setting up this product, take care that no undue force is applied to the opening / closing sections
or moving sections of the game machine. Failure to do so could cause injury, accidents or product damage.
•This product is an indoor game machine. Never set up the game machine outside.
·Setting up this product outside could result in accidents or equipment failure.
•Do not set up the game machine near emergency exits.
·Doing so could block exits in time of emergency and could result in death or serious
injury.
•Do not set up the game machine.
·In a place exposed to rain or moisture.
·In a place exposed to direct sunlight.
·In a place exposed to direct heat from air-conditioning and heating equipment, etc..
·near hazardous flammable substance such as thinner and kerosene.
·on an inclined or uneven floor.
·near fire extinguishing equipment.
·in a place exposed to strong vibration.
·in a place exposed to excessive dust.
·near equipment generating strong magnetism or electric waves.
•Do not place containers holding chemicals or water on or near the game machine.
·Electrical shock or damage could be caused by water or foreign matter entering the
inside of the machine.
•Do not place objects near the ventilating holes.
·Doing so could cause the internal temperature to rise excessively, resulting in fire or
equipment failure.
•Do not bend the power cord by force or place heavy objects on it.
·Doing so could result in electric leakage or fire.
•Never plug or unplug the power cord with wet hands.
·Doing so could result in electrical shock.
•Never unplug by pulling the power cord.
·Doing so could damage the cord, resulting in electric leakage or fire.
禁止
禁止
Precautions for use
3
WARNING

4
Setting Up
•Be sure to use indoor wiring for within the specified voltage range. For extension cord, use
indoor wiring of the specified rating or more.
·Failure to do so could result in fire or equipment failure.
•Never plug more than one cord at a time in the electrical receptacle.
·Doing so could result in fire or electrical shock.
•Do not lay the power cord where people walk through. You may tread on or stumble
over them.
·You may fall down and get injured or the cord may get damaged.
•Do not put anything heavy on the pipe connecting the projector unit and the cockpit
unit, nor pull the pipe forcibly. Never install the machine with the pipe being
disconnected and the bundled wires being exposed. (GN672-UC only)
·Doing so could redult in eguipment failure, electrical shock or fire.
•Be sure to connect the attached grounding wire. (See page 28.)
·Failure to do so may result in electric shock or trouble.
•Clearances of 100 mm (3.94in) or more should be created between the game
machine and walls.
プグ
CAUTION
Operation
4
WARNING
Precautions for use
•If there is any abnormality such as smoke, bad smell or abnormal noise being
emitted from the machine, immediately turn OFF the power switch and unplug the
power cord from the receptacle to stop operating it.
·Using the machine in abnormal conditions could result in fire or accidents.
In case of abnormality
1Turn OFF the power switch.
2Unplug the power cord from the receptacle.
3Contact your nearest dealer.
•Do not leave the power cord plugged improperly or covered with dust.
·Doing so could result in electrical shock or fire, so inspect the power cord periodically.
•Never disassemble, repair or modify any section other than those specified in this
manual.
·Doing so could result in fire, malfunction or equipment failure.
·Ask your nearest dealer to perform repairing, etc..
·We do not assume any responsibility for any damages that would be caused
by tampering with the machine.
禁止

5
Operation
•Do not use this product anywhere other than industrial areas.
·Using in a residential area or an area next to a residential area could affect signal
reception of radios, television sets, telephones, etc..
•The following users should not play the game.
·Doing so could cause accidents or illness.
·Those under the influence of alcohol. ·Those suffering from or being treated for arm or
wrist ailments.
•Do not plug or unplug the power cord with wet hands.
·Doing so could result in electrical shock.
•When handling the power cord, take care of the following:
·Improper handling could result in fire or electrical shock.
·Do not damage the power cord. ·Do not modify the power cord.
·Do not bend the power cord excessively. ·Do not twist the power cord.
·Do not heat the power cord. ·Do not pull the power cord.
·Do not bind the power cord. ·Do not tread on the power cord.
·Do not sandwich the power cord. ·Do not drive a nail into the power cord.
•If the power cord or power plug becomes damaged, stop using the machine
immediately and ask your nearest dealer to replace the parts.
·Using a damaged power cord or power plug could result in fire or electrical shock.
•Do not place anything on the machine. Do not give shock and impact to the
machine either.
·The thing may drop or the machine get damaged, which may get you injured.
CAUTION
•Be sure to turn OFF the power switch and unplug the power cord from the
receptacle before inspecting or cleaning the machine.
·Failure to do so could result in electrical shock.
•When replacing parts, be sure to use parts of the correct specifications. Never use
parts other than the specified ones.
·Using improper parts could result in fire or equipment failure.
•Do not allow other persons than qualified engineer to open the back door of the
projector unit and the front door of the cockpit unit. (GN672-UC)
·Otherwise, an accident or electric shock may result.
•Allow only a qualified engineer to open the back door. (GM672-UC)
·Otherwise, an accident or electric shock may result.
•Never disassemble, repair or modify any section other than those specified in this
manual.
·Doing so could result in fire, malfunction or equipment failure.
·Ask your nearest dealer to perform repairing, etc..
·We do not assume any responsibility for any damages that would be caused
by tampering with the machine.
•To clean the game machine, wipe it with a soft cloth dampened in a neutral detergent
and wrung out.
·Using organic solvents such as thinner may decompose the material.
·Electrical shock or equipment failure could be caused by water entering the inside
of the machine.
WARNING
禁止
禁止
Precautions for use
Inspection and cleaning
禁止
5

6
Moving and transportation
6
Precautions for use
CAUTION
禁止
•The game machine contains parts such as the projector (GN672-UC), monitor (GM672-
UC), electronic components and precision components which are sensitive to
vibrations and impacts. Great care therefore should be taken when moving and
transporting the game machine. Be sure not to let the machine tip over.
•Before moving the GN672-UC machine, be sure to separate the cockpit unit and the
projector unit and fully raise the 10 level adjusters. Move the units on the casters.
In the case of GM672-UZ machine, fully raise the 6 level adjusters and move the unit
on the casters. Be sure to turn OFF the power switch and unplug the power cord.
·Otherwise accidents, machine damage or trouble may result.
•When moving the units, use care not to apply undue force to them. (GN672-UC)
·Particularly in the case of the projector unit, application of undue force may bring down
the unit, resulting in an accident or damage.
•When moving the units, use care not to apply undue force to the connections of the
cockpit. (GN672-UC)
·Application of undue force may cause injury, accident or damage of the machine.
•When moving the machine, use care not to apply undue force to the connections of
the machine. (GM672-UC)
·Application of undue force may cause injury, accident or damage of the machine.
Disposal (GN672-UZ only)
WARNING
PRECAUTION
IN HANDLING
•When setting up, inspecting, maintaining, moving or transporting this product, follow the
procedures and instructions set forth in this manual and perform such work safely.
•Do not remove labels of “WARNING”, “CAUTION”, etc. attached to the product.
•Do not set up, handle, inspect, maintain, move or transport this product under conditions equivalent
to the condition of “WARNING” or “CAUTION” specified in this manual.
•If a new owner is to have this product as a result of transfer, etc., be sure to give this manual to the new owner.
•When disposing of the projector of this product, do not leave it with the screen
exposed.
·Doing so could result in fire due to direct sunlight, etc..
•When disposing of the projector with the screen section removed, do not hold the
screen section to direct sunlight, etc..
·Doing so could cause burns or fire.
禁止

7
MEMO

8
Specifications
Dimensions
Weight
Rated power consumption
Monitor
Service condition
Attachments
Refer to the figure above: mm(in.)
Total weight: Approx. 276 kg(609lb)
Cock pit unit:Approx. 135 kg (298lb), Projector unit:Approx. 141 kg (311lb)
250W
50-inch color projector
Temperature 10 to 35˚C (50 to 95˚F), Humidity 20 to 80%(No dewing is allowed.)
· Instruction manual ...........................................................This manual
· Keys for coin door.............................................................................2
· Keys for maintenance...................................................................... 2
· Spare fuse (10A) .............................................................................. 1
· Unit connecting pipe ......................................................................... 1
· Unit connecting pipe fixing screw (M4 x 10L) ................................... 4
(M4 x 20L) ................................... 4
· Grounding wire ................................................................................. 1
· Projector adjusting remote controller................................................ 1
· UM-4 (AAA batteries)........................................................................ 2
· Label for remote control for adjusting projector ................................ 1
1 Specifications
•If any part is defective or not found, contact your nearest dealer.
•The specifications of this product are subject to change without notice for reasons such as improving the
performance.
•GN672-UC
2200 to 2600 (86.7 to 102.4)1146 (45.1)
1190 (46.9) 747 (29.4)
601 (23.7)
1929 (75.9)

9
Specifications
Dimensions
Weight
Rated power consumption
Monitor
Service condition
Attachments
Refer to the figure above: mm(in)
Total weight:Approx. 203 kg(448 lb)
Main unit:Approx. 159 kg (351lb), Seat unit: Approx. 44 kg (97 lb)
160W
29-inch color monitor
Temperature 10 to 35˚C (50 to 95˚F), Humidity 20 to 80%(No dewing is allowed.)
· Instruction manual ...........................................................This manual
· Keys for coin door............................................................................. 2
· Keys for maintenance...................................................................... 2
· Spare fuse (10A) .............................................................................. 1
· Grounding wire ................................................................................. 1
•If any part is defective or not found, contact your nearest dealer.
•The specifications of this product are subject to change without notice for reasons such as improving the
performance.
1 Specifications
•GM672-UC
1535 (60.4)
858 (33.8)
806 (31.7)
1822 (71.7)

10
2 Names of parts and list of main parts
•GN672-UC
16
1
2
3
4
5
6
78
9
1011
12
13
14 15
17
18
19 20
21
22
23
24
25
26
27
28 29
30
31
32
33
34
3536
37
38
2829

11
2 Names of parts and list of main parts
Projector unit
Projector
Projector maintenance door
Projector adjustment PCB
Projector input panel
Fluorescent light unit
Cock pit unit
Control lever
Joint fitting A
Joint fitting B
Joint fitting C
Seat
Coin door unit
Coin input port
Coin return lever
Coin return port
Maintenance door
Coin selector
Coin door
Coin box
Coin counter
Service panel switch
AC bracket
AC power cord
Power switch
Fuse holder
Ground terminal
Caster
Adjuster
Switching power
Switching power
Game PC board
Speaker
Super woofer
POWER UP button
VIEW SHIFT button
Unit connecting pipe
Transformer
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
12
10
1
1
1
2
1
1
1
1
1
Part # Quantity RemarksNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Part name
0000030701
0000002526
0000008689
-
-
0000002522
0000030697
0000030691
0000030508
0000030509
0000030510
0000030546
0000003820
-
-
-
-
-
-
0000006850
0000030431
0000005098
0000030489
-
0000003197
0000005985
0000005622
0000002051
0000002405
0000030690
0000030688
-
0000002616
0000003182
0000030686
0000030685
0000030698
0000002728
Include 14 to 19
Main PCB (5V)
Main PCB (12V)
1set
Fuse (10A)
•GN672-UC

12
•GM672-UC
1
2
4
5
6
78
9
10 11
12
13
14
15
17 18
19
20
21
22
23
24
25
26
27
28
30
32
33
34
16
3
31 29
2 Names of parts and list of main parts

13
2 Names of parts and list of main parts
Main unit
Seat unit
Fluorescent light unit
29-inch color monitor
Seat
Joint fitting A
Joint fitting B
Joint fitting C
Control lever
Speaker
Coin door unit
Coin input port
Coin return lever
Coin return port
Maintenance door
Coin selector
Coin door
Coin box
Coin counter
Service panel switch
Monitor adjustment PCB
AC bracket
AC power cord
Power switch
Fuse holder
Ground terminal
Caster
Adjuster
Switching power
Switching power
Game PC board
POWER UP button
VIEW SHIFT button
Transformer
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
8
6
1
1
1
1
1
1
Part # Quantity RemarksNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Part name
-
-
0000003575
0000036033
0000030546
0000031242
0000030509
0000030510
0000030691
0000002616
0000003820
-
-
-
-
-
-
0000006850
0000030431
0000005098
-
0000030489
-
0000003197
0000005985
0000005622
0000002051
0000002405
0000030690
0000003800
-
0000030686
0000030685
0000002728
1set
Include 12 to 17
Main PCB (5V)
Main PCB (12V)
Fuse (10A)
•GM672-UC

14
3 How to play
“SOLAR ASSAULTTM” is a machine to play 3D polygon shooting game, the latest version of
the “GRADIUS” Series. Enjoy shooting enemies by commanding the power-up weapons,
aiming at higher score.
How to play
•Shoot enemies appearing one after another and get higher score.
•How to attack enemies
Use each of the missile, shotgun, laser gun and
sharpshooting laser gun properly for shooting down
enemies.
Missile button
·Number of missiles is infinite.
·In the power-up mode, you can fire the missile.
(It is not possible to fire at the initial stage.)
Trigger button
·Number of shots (ordinary bullets) is infinite.
·In the power-up mode, you can fire the laser gun.
·When the auto power-up mode has been selected,
this button is effective commonly for operating the
trigger and firing the missiles.
1Put a coin into the slot and press the VIEW SHIFT button to start the game.
(It is possible to start the game also by pulling the trigger.)
2You can choose your favorite main fighter among the following three models.
VIC VIPER LORD BRITISH
ALPINIA
Missile button
Press this butting when
firing the missiles.
Trigger button
Press this button when
firing the shotgun. This
button can also be used
simultaneously with the
missile button. If both
the buttons are pressed
at once, you can fire the
sharpshooting laser gun.
•Fighter for advanced-level players
Missile : Fired in front downward direction from the mainfighter.
Double: Bullets are fired in front and front upward
directions.
Laser : Laser beam, which has penetrating destructive
power, can destroy or give damage to plural
enemies in a row. In the sharpshooting mode,
enemy attacking range enlarges.
Option : Sub-fighter having the same equipment as that
of the main fighter. It traces the movement of
the main fighter.
Shield : Protects shooting attack from enemy.
•Fighter moving at high speed
Missile : Fired in front right and left directions from the main fighter.
Double: Bullets are fired in front direction. They are also
fired in the direction inputted by the lever.
Laser : Circular laser beam covering a large enemy
attacking range. In the sharpshooting mode, the
circle of laser beam expanding in a wide range
captures enemies and attacks them.
Option : Same as that of VIC VIPER.
Shield : Same as that of VIC VIPER.
•Fighter for beginners
Missile : Guided missile is launched.
Double: Bullets are fired in three directions: front, upward
and downward, and right and left.
Laser : Short laser beams are emitted simultaneously in
parallel. In the sharpshooting mode, the fighter
searches and attacks enemies.
Option : Same as that of VIC VIPER.
Shield : Same as that of VIC VIPER.

15
3 How to play
3The power-up operation is selectable from the following two modes:
·Manual power-up .............. After acquisition of power-up items, the player can
decide the power-up equipment by himself.
·Auto power-up................... After acquisition of power-up items, the power-up
equipment is decided automatically.
4Then, get the game started. Attack enemies appearing one after another, aiming at
getting high score.
5When the fighters are attacked by enemy, they are destroyed by explosion. If there
survives any fighter at that time, reserved fighter appears. When all the fighters are
destroyed, the game is over.
The number of surviving fighters increases according to the score.
(Set the number of fighters kept in reserve at the start of game, according to “GAME
OPTIONS” on page 23.)
Shifting of view point
The view point of the player can be changed any time during play by pressing the VIEW
SHIFT button.
Continuing the game
The continuation of game is accepted for about 20 seconds before the game is over.
When the game is continued in the “Continue” mode, the power of equipment is dropped
about a half. (When selecting the “Continue” mode, set the position for resuming the game
according to “GAME OPTIONS” on page 23.)
Types of power-up
The types of basic power-up are as shown below. They vary depending on the type of
fighter. (See page 14.)
·Missile …… Enables you to use a missile which can be reinforced in two stages for
each fighter.
·Double …… Enables you to shoot bullets to other directions than the front.
·Laser……… Enables you to emit laser beam of high attacking power.
·Option …… Sub-fighter having the same equipment as that of the main fighter.
·Shield …… Barrier to protect the fighters from attack of enemy.
How to power up
When enemies in formation, a red-marked enemy or specific enemy is destroyed, the
enemy emits a power-up capsule when destroyed. The number of capsules currently
acquired is displayed on the power-up gauge. When the gauge reaches the level enough
for power-up, you can use weapons you want.
·In the manual power-up mode, press the power-up button while the gauge of desired
item is lit.
·In the auto power-up mode, power-up becomes effective automatically when you
acquire a capsule.
How to use the sharpshooting laser gun
When the fighter is equipped with the laser gun, it is possible to emit sharpshooting laser
beam. To emit sharpshooting laser beam, press both the trigger button and the missile
button at the same time and release them after the elapse of certain time. The attacking
power is increased by prolonging the button hold-down time.

16
4 Opening and closing the doors
4-1 Opening and closing the maintenance door
How to open the maintenance door
1Insert the attached maintenance
key into the keyhole of the door in
the upper portion of the coin door
unit, and turn it clockwise.
How to close the maintenance door
•Take care not to apply any load or impact to the maintenance door when
it is open.
2Open the maintenance door.
1Close the maintenance door.
2Turn the maintenance key counterclockwise.
Maintenance door
GN672-UC
GM672-UC

17
4 Opening and closing the doors
4-2 Opening and closing the coin door
How to take out the coin box
1Insert the attached coin box key
in the coin box door and turn it
clockwise.
2Open the coin door and take out
the coin box.
Coin counter
You will find the coin box when
the coin door is opened. The coin
counter is located under the coin
box.
•Securely lock the door for protection against burglaries.
•Note that the coin box is considerably heavy to take out if it is full of coins.
Coin door
Coin box
Coin counter

18
5 PCB settings
5-1 PCB start-up check (self test)
When the power switch is turned ON after installation of machine, the performance
of game Printed Circuit Boards (PCB) is checked automatically and the result is
displayed on the screen.
•Be sure to perform the self test before using the machine.
•If an abnormality persists or the machine does not operate properly,
immediately turn OFF the power switch, unplug the power cord from the
receptacle and contact your nearest dealer.
Result of test
·The machine goes to the game mode and the demonstration game gets started.
If test is OK
· “ BAD ” appears on the screen, and the checking is repeated.
If “24G BAD” is displayed, once turn OFF the power switch and then turn it ON
again while depressing the test switch button on the service panel. (The content
of setting in manual test return to those having been set at the time of shipment.)
After the installation of the machine, or after the repair or replacement of PCB,
turn ON the power switch while pressing the test switch on the service panel and
once return the settings to the factory settings.
If an abnormal display continues or the machine does not operate normally,
immediately turn OFF the power switch and contact your nearest dealer.
If any abnormality is detected