Kozyard Edward User manual

Assembly Manual
10’x12’ Edward Polycoabonate gazebo
Kozyard LLC Products
© Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.

3. Wearing protective gloves
is recommended.
4.You may need a safety hat.
6.Please use a Phillips
screwdriver.
8.For ease of construction, you
may need to use a drill.
2.You will need one or more
stepladders.
5.Use the hex keys in the box.
2+
1.Two or more people are required
for assembly.
7.Do not fully tighten screws
prior to complete assembly.
10x12' ANCHOR BLUEPRINT
357.5 cm/11.7'
15cm/5.9"
30x30cm/11.8"x11.8"
cm/9.6’ 262.5 cm/8.6’
327.5 cm/10.7'
292.5
EDWARD

Pole
Beam
Beam Corner Roof Bar
Corner Roof Bar
Corner Solidifying Bar
Corner Solidifying Bar
Solidifying Bar
Solidifying Bar
Finishing Bar
Finishing Bar
Stand Palete
Hook
Finishing Bar
Solidifying Bar
Beam
Beam

Joint
Cover
Finishing
End
Finishing
End Panels
Panels
Panels
Joint
Cover
Allen
Key
Screws
Spike Screws Screws
Screws Screws Screws
Driver
Solidifying
Bar
Solidifying
Bar
Panels Side Wall Mosquito
Net
Panels Panels Panels
Panels
Corner
Cover
Outside Roof
Connector
Inside Roof
Connector

Set up poles (Part A) with stand paletes (Part B) using
screws ①as shown in diagram.
Step 1:
Put 6 hooks（Part H) to each slot of
sidewall track (Part C&C1).
Then connect Part C and
Part C1 into one beam
using screws ④as shown
in diagram.
Step 2：
Put 7 hooks（Part H) to each slot
of sidewall track (Part C2&C3).
Then connect Part C2 and Part C3
into one beam using screws ④
as shown in diagram.
6PCS
X4
X2
X2

Step 3：
Step 4：
Use screws ③to contect
poles and beams together
as shown in diagram.
X4 X4
X4
Finish connecting beams using corner
covers (Part K)and screws ②as shown
in diagram.
Affix middle beams
using joint cover (Part J&S)
and screws ①&②as
shown in diagram.

X4
Step 5：Affix the frame with corner Solidifying Bars
(Part G and G1) by using Screws ④as
shown in diagram.
Set up roof frame.
Step 6：
Connect the inside roof
connect (Part L) with
the corner roof bar (Part D)
using Screws ④as shown
in dragram.

X2
X6 X4
Step 7：
Attach roof bar (Part D1) to inside roof connector(Part L) using screws ④
as shown in diagram.
Attach roof bar
(Part D1&D) to main
frame using screws ④
as shown in diagram.

Step 8：Connect outside roof connector (Part L1) to inside roof
connector (Part L) using screw ⑤as shown in diagram.

N/N1/Q
Overall Half Roof Assembly
Step 9: Insert Panels (Part N/N1/Q) to the slot of roof bar (Part D&PartD1)
as show in diagram.
Insert Solidifying Bars (Part E
&Part E1)to the slot of roof
bars (Part D&Part D1)to fix Panels
as shown in diagram

Overall Roof Assembly

D
or
Step 10：
X8
Affix Solidifying Bar (Part U &Part U1) to the Beam (Part C or Part C1)
Then,Insert another side of Solidifying Bar (Part U & Part U1) to the
Corner roof bar (Part D)

P/Q1/P1
Step 11：
Insert Panels (Part P&Part Q1&Part P1) to Roof Bars(Part D&Part D1)
Then affix Finishing End (Part F, Part F1 &Part F2) to Roof Bars using
Finishing End (Part M & Part M1) and Screws ④as shown in diagram.
0
Attention:Cover the solidifying
bars (PartU&Part U1) using finishing
bar (Part F&Part F1)

RRR
R
R1
R1
1.) Securing just
the netting. 2.) Securing netting
and curtains.
3.) Use all ties for
winding conditions.
There are three ways to secrue your netting and curtains to
the legs using the include 4 ties.
X4
Attention：Change hook: take out Part S
and Part H into the slot.
Step 12：
Hang up solid sidewall and Mosquito net (Part R&Part R1)
as shown in diagram.

Step 13：Secure the Paletes (Part B) using spike (Part V)
At the end of process, tighten all srrews before using.
Attention:It is better to anchor
the plates to ground as blue print.

© Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.
Kozyar
A
Mer W
66