Kozyard Victoria User manual

Victoria 10’x12’ Gazebo
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.

Safety Information
Care Instructions
..
WARNING: This garden house Gazebo is NOT a permanent structure and is designed for sunshade and privacy and must be used under
normal weather conditions. We recommend removal of the fabric canopy in windy conditions as gazebos catch wind similar to umbrellas. You
must however completely disassemble the unit prior to any severe weather conditions such as thunderstorm, hurricane, and/or heavy wind and
rain. Failure to remove the fabric canopy or disassemble the unit will cause the gazebo to have structure damage or even structural collapse
WARNING: Keep all frame and heat sources away from this tent fabric . This tent is made with fabric that meets CPAI-84 specification for
flame resistance,It is not fire proof.The fabric will burn if left in continuous contact with any flame source. The application of any foreign
substance to the tent fabric may render the flame-resistance properties ineffective.
CAUTION: Keep all children and pets away from assembly area.
Begin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, clothes line or electrical wires.
Some parts may contain sharp edges, wear protective gloves if necessary. At least two or more people are recommended for safe assembly.
concrete surface
CAUTION: Always install on level ground utilizing tie down cords and ground stakes. Do not permanently anchor unit to wood
deck or concrete surface.
CAUTION: Garden house fabrics are water resistant but not water proof and may leak during precipitation. Fabrics will fade
from direct exposure to sunlight.
Before using, wipe with a clean, dry cloth. Do not use bleach or solvents. Treat the frame with one-step liquid wax for maximum protection
against UV light and salty damp air. Wash the canopy with a mild solution of soap and water, rinse throughly, air dry completely. .
Please properly tighten all hardware and perform periodic inspections during usage for cracked welds.
3. Wearing protective gloves
is recommended.
4.You may need a safety hat.
6.Please use a Phillips
screwdriver.
8.For ease of construction, you
may need to use a drill.
2.You will need one or more
stepladders.
5.Use the hex keys in the box.
2+
1.Two or more people are required
for assembly.
Tool Required:
7.Do not fully tighten screws
prior to complete assembly.

K1
Pole
Beam
Beam Beam
Corner Roof Bar Corner Roof Bar
Roof Bar
Roof Bar Plate
Roof Bar
Beam
Pole
Roof bar
Roof
Connector
Roof
Fabric
Roof
Fabric
Netting Spike Spike Rope
Part list

Allen key Screw Screw Screw

Step 1
A:Connect Connector (Part G) to Pole (Part A) using screw 1# as shown in diagram.
B:Link Pole (Part A)to Pole (Part A1)using screw 1#
as shown in diagram.
C:Attach Pole (Part A1)to Plate (Part B)using screw 1#
as shown in diagram.
X4

Step 2: Connect Beam (Part C) to Beam (Part C1) using screw 3# as shown
in diagram.
Connect Beam (Part D) to Beam (Part D1) using screw 3# as shown in diagram.
X2
X2

Step 3: Connect finished Beam (Part C&Part C1) and finished Beam (Part D&Part D1)
to finished poles using screw 1# as shown in diagram.
Attention:
All the beam connecting turn must be followed
as above shown in diagram.
D1

H
H
Step 4: A: Attach Roof bar (Part H) to Roof Bar (Part E) using Screw 2# as shown in
diagram.
B: Insert Roof bar (Part E1) to Roof Bar (Part E)
as shown in diagram.
C: Insert Roof bar (Part F1) to Roof Bar (Part F)
as shown in diagram.
X4
X2

2
2
2
2
Overall upward view
Downward view
Insert roof bars to roof connector(Part J) as shown
in diagram.

Step 5:
A: Attach Roof bar (Part F1) or (Part F2) to finished beams using Screw 1#
as shown in diagram.
B: Attach Roof bar (Part E1) to finished poles
using Screw 2# as shown in diagram.

K1 K1
Step 6: Put Roof Fabric (Part K& Part K1) to roof frame as shown in diagram.

Step 7:
A:Hang Netting (Part L) on finished beams as shown in diagram.
B:Secure the plate (Part B) to the ground using Spike (part M)

Step 8: Measure out from post to the longest possible distance(to best use the
length of the Rope (Part P) and secure Anchor (Part Q) to ground at 45 degree as
shown in diagram.
N
At last , Make sure all of screw are fixed tightenly before use.

© Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.
Kozyar
A
Mer W
66