Kozyard Alexander User manual

Assembly Manual
12’x14’ Alexander Hardtop Gazebo
With Double Roof
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

12 x14'
'ANCHOR BLUEPRINT
6.77 in 12 in.
12 in.
φφ
160.7 in.
136.88 in.
ø0.31 in.
2+
Safetyglasses
• Please read and follow this assembly and operation guide to reduce the risk of personal injury
and damage to your gazebo.
• Do not discard any of the packaging until you have checked that you have all the parts in place.
The maximum weight capacity of this gazebo roof is 2500 pounds.
• Sidewalls and nettings should be off or in the opened position and tied to poles when winds are
over 30 MPH to avoid damage.
• Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precau-
tions to reduce the risk of injury. Please note that this item contains small parts which could be
swallowed by children. Keep it out of reach of children under 3 years old and pets during installa-
tion.
Warnings and Cautions
Two or more people are required
for aseembly and disassembly.
Pre-assembly
Tools that may be required.(Not included in boxes)
Note: Tools are not shown to actual size and scale.
Do not fully tighten screw prior to
complete assembly.
Anchoring poles into concrete is strongly recommended.
Ensure the gazebo is positioned on level ground
Recommended Min. Anchor Block Size

page 1
Alexander 12’X14’ assembly manual
A x4
E72 x2
F x4 G x4
J1 x4 J2 x4
K4 x1
K14 x1
L x4
H x4
H1 x4
B6 x2
B61 x2
C6 x2
C61 x2
B62 x2
C62 x2
D7 x2
E7 x2
E71 x2
D71 x2
D72 x2
H2 x1
M3=M1+M2 M1 x4
M2 x4
N1 x2
N4 x2
ITEM
A
B61
B62
C6
C61
C62
D7
D71
D72
E7
E71
E72
F
G
H
H1
H2
H3
J1
J2
K4
K14
L
B6
DESCRIPTION
Pole 4
2
2
2
2
2
2
2
2
2
2
2
2
4
2
2
4
4
4
4
4
4
4
4
1
1
1
1
Beam
Beam
Beam
Jointer Bar
Sidewall Track
Jointer Bar
Beam
Jointer Bar
Jointer Bar
Union Bar
Corner Cover
Joint Cover
Joint Cover
Silcone Rubber
Plate
Corner Solidifyng Bar
Corner Solidifyng Bar
Inside Roof Connector
Outside Roof Connector
Sidewall Track
Sidewall Track
Sidewall Track
QTY
M1
M2
N1
N4
Short Corner Roof Bar
Corner Roof Bar
Roof Bar
Roof Bar
H3 x1
Double-sided adhesive tape
Attention: Prior to assembly, verify that all parts and pieces are included to ensure
an efficient installation process.

page 2
Alexander 12’X14’ assembly manual
Q4 x2
Q13 x2
U3 x4
R x8
T2 x2
T4 x2
U1 x4
U6 x4
Sx128
U4 x4
Q14 x2
P2 x2
P12 x2
V11 x2 V12 x2
V43 x2 V44 x2 V45 x2 V46 x2
W12 x2
W16 x2 W17 x2
W11 x2
W15 x2 W18 x2
W13 x2 W14 x2
ITEM DESCRIPTION QTY
P2
P12
Q4
Q13
Q14
R
T2
T4
U1
U3
U4
V11
V12
V43
V44
V45
V46
W11
W12
W13
W14
W15
W16
W17
W18
U6
S
Net Frame
Net Frame
Net Frame
Finishing End
Finishing Bar
Finishing Bar
Finishing Bar
Finishing Bar
Solidifying Bar
Solidifying Bar
Iron Angle
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Iron Angle
Spacer
2
2
2
2
2
128+2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
8

page 3Alexander 12’X14’ assembly manual
1# x246+4
5# x80+2
6# x8+1
7# x36+2
9# x24+2
10# x4+1
11# x12+1
Allen key
Wrench
2# x16+2
3# x16+2
4# x120+2
Y3 x2
S3 x2
SY x4
S4 x2
Y4 x2
Z x76
Z2 x4
Z4 x2
Z1 x4
Z3 x2
X41 x2 X42 x2 X43 x2 X44 x2
X45 x2 X46 x2 X47 x2 X48 x2
X41
X42
X43
X44
X45
X46
X47
X48
S3/S4
Y3/Y4
Z
SY
Z1
Z2
Z3
Z4
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
2
2
2
2
2
2
2
2
ITEM DESCRIPTION QTY
2#
1#
3#
4#
5#
6#
7#
9#
10#
11#
12#
Mosquito Net
Solid Sidewall
Strap
Bracket
Bracket
Bracket
Bracket
Bracket
Screws
Screws
Screws
Hook
Screws
Screws
Screws
Screws
Screws
Screws
Washer
4
4
4
76+2
4
4
2
2
246+4
16+2
16+2
120+2
80+2
8+1
36+2
4+1
12+1
12+2
24+2
12# x12+2

Alexander 12’x14’ assembly manual page 4
A x4
L x4
1#
x12
A
L
1#
1#
1#
Parts Required:
X4
A
L
X12
3 inches
3/8
inches
M6
(Not included)
1. Set up Poles (Part A) with Stand Plates (Part L) using screws 1# as shown
in the diagram.
Step 1: Set up Poles
Reference for anchoring gazebo:
• If the ground is concrete and its depth is over 3 inches, you can purchase 3/8"
diameter x 3" length sleeve anchors.
• Only anchor after finishing all the assembly.
Attention: After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as
shown above. Damage resulting from wind or improper anchoring is not covered under warranty.

Alexander 12’X14’ assembly manual
1#
X24
D7 x2
C6 x2 B6 x2
E7 x2
F x4
D7
E7
E7
D7
F
1#
1#
1#
1#
Parts Required：
X2
Short Beam Overall:
1. Connect (Part C6,B6) into one beam using Union bar (Part F) with screws 1#
as shown in the diagram.
Long Beam Overall:
2. Connect (Part E7,D7) into one beam using Union Bar (Part F) with screws 1#
as shown in the diagram.
X2
B6
C6
F
X2
X2
F
1#
1#
1#
1#
C6
B6
C6
B6
D7
E7
F
page 5
Step 2: Connect the Beams

Alexander 12’X14’ assembly manual
1# x96
1#
1#
1#
1#
page 6
Parts Required:
Step 3: Connect Joint Bars and Tracks with Beams
C61,E71
C6,E7
B6,D7
B61,D71
C62,E72
B62,D72
X2
X2
B6
C6
B61
C61
C62 B62
E72 D72
C61 x2
C62 x2
B61 x2
D71 x2
D72 x2
B62 x2
E71 x2
E72 x2
D7
E7
D71E71
1. Connect Joint Bars (Part C61,C62), Tracks (PartE71,E72) to Beams (Part C6 and
E7) using screws 1# as shown in the diagram.
Tip:
Do not tighten all screws on the Jointer
bars (Part B61, C61, E71, D71) until the
screws of the roof panels are aligned in
place.
2. Replicate the same steps for Joint
Bars (Part B61 and D71), Tracks (Part
B62 and D72), attaching them to Beams
(Part B6 and D7) using screws 1# as
shown in the diagram.

Alexander 12’X14’ assembly manual page 7
Parts Required：
Use screws 3# first, then use screw 2# to connect
Poles and Beams together as shown in the diagram.
2#
x16
3#
x16
②
②
①
①
2
2#
#
A
A
B6
B6
D7
D7
B6
C6
C6
C6
E7
C6
X8
X8
X2
X2
3#
3#
A
A
A
A
B6
B6
C6
D7
E7
E7
Tip:
At least three people
for this step.
3+
Step 4: Set up Poles and Beams
Tip:
Place parts on carpet or rug
to avoid scratches during
assembly.

Alexander 12’X14’ assembly manual page 8
Parts Required:
Step 5: Connect Solidifying Bars with Beams and Poles
J2
J1
J2 x4
J1 x4 1#
x32
1#
1# 1#
X4
Diagonal 1
Diagonal 1 = Diagonal 2
Diagonal 2
J1
J2 J 1
J2
J1
J2
J1
J2
Affix the frame with Corner Solidifying Bars (Parts J1, J2) using screws 1# as shown
in the diagram.
Tip:
Measure (DIAGONALLY) from posts to posts to
assure alignment so all materials fit as planned.