Kramer KDS-USB2 Kit User manual

KDS-USB2 Quick Start
P/N:
2900- 301391QS
Rev:
2
Scan for full manual
KDS-USB2 Kit/KDS-USB2-EN/KDS-USB2-DEC
Quick Start Guide
This guide helps you install and use your KDS-USB2 for thefirst time.
Go to www.kramerav.com/downloads/KDS-USB2 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
KDS-USB2-EN and/or KDS-USB2-DEC
1 Power adapter and cord (for KDS-USB2-DEC)
1 Quick start guide
1 USB2 cable A male to B male (for KDS-USB2-EN)
Step 2: Get to know your KDS-USB2
KDS-USB2-EN
#
Feature
Function
1
Power LED
Lights blue when power is supplied. Off when the host computer does not supply power.
2
Link LED
Lights green when a USB link is established between the encoder and the decoder.
Flashes slowly when the unit attempts to establish a link. Flashes quickly when in pairing mode.
Off when a link is not established.
3
Host LED
Lights green when KDS-USB2 is properly enumerated on the host computer.
Flashes when in a suspended state.
4
Activity LED
Lights yellow when activity between the decoder and encoder/s is detected.
Off when in suspended mode.
5
Config Button
For factory use.
6
Mode Button
Use for pairing KDS-USB2-EN with the KDS-USB2-DEC decoder/s.
7
USB Host Port
Connect to the host computer.
8
Link RJ-45 Connector
Connect to the KDS-USB2-DEC.
KDS-USB2-DEC
#
Feature
Function
9
USB Ports
Connect up to 4 USB type A devices.
10
Power LED
Lights blue when power is supplied. Off when the host computer does not supply power.
11
Link LED
Lights green when a USB link is established between the encoder and the decoder.
Flashes slowly when the unit attempts to establish a link. Flashes quickly when in pairing mode.
Off when a link is not established.

#
Feature
Function
12
Host LED
Lights green when KDS-USB2 is properly enumerated on the host computer. Flashes when in a
suspended state.
13
Activity LED
Lights yellow when activity between the decoder and encoder/s is detected. Off when in
suspended mode.
14
24V Power Connector
Connect to the supplied power adapter.
15
Config Button
For factory use.
16
Mode Button
Use for pairing KDS-USB2-EN with the KDS-USB2-DEC decoder/s.
17
Link RJ-45 Connector
Connect to the KDS-USB2-EN.
Step 3: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your KDS-USB2.
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
You can also connect multiple KDS-USB2-DEC and KDS-USB2-DEC units.
To achieve specified extension distances, use the recommended Kramer cables available at
www.kramerav.com/product/KDS-USB2.Using third-party cables may cause damage!
Step 4: Connect power
Connect the power cord to KDS-USB2 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 5: Operate KDS-USB2
By default, the KDS-USB2 kit devices are paired. You can also pair devices manually or map multiple devices via Kramer
Control.
When using unpaired units (for example, individually
purchased devices), you can pair them manually.
To pair KDS-USB2-EN with KDS-USB2-DEC manually:
1. Make sure that the devices are properly connected.
2. On KDS-USB2-EN, press and hold Mode for a few
seconds.
The Link LED flashes.
3. On KDS-USB2-DEC, press and hold Mode for a few
seconds.
The Link LED flashes.
4. Wait until both Link LEDs light.
Devices are paired.
If you are using Kramer Control, you can easily map multiple
encoders to decoders.
To pair KDS-USB2-EN devices with KDS-USB2-DEC
devices via Kramer Control:
1. Launch Kramer Control builder to select the space.
2. Add the KDS-USB2 devices and import their drivers.
3. For each device, add its IP address.
4. Map a single encoder to several decoders, or several
decoders to one encoder, as desired.
For further information, go to:
www.kramerav.com/page/knowledgebase-control