Kramer WP-EN6 User manual

WP-EN6 Quick Start
P/N:
2900- 301328QS
Rev:
2
Scan for full manual
WP-EN6 Quick Start Guide
This guide helps you install and use your WP-EN6 for the first time.
Go to www.kramerav.com/downloads/WP-EN6 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
WP-EN6 Video Encoder
1 Quick start guide
Installation accessories
Frame (or frame set) and faceplate
Step 2: Get to know your WP-EN6
FRONT PANEL BACK PANEL
#
Feature
Function
1
IR TX on a 3.5mm Mini Jack
Connect to an emitter.
2
USB Type B Port
Connect to a USB host, for example, a PC.
3
HDMI™ IN Connector
Connects to an HDMI source.
4
IR RX on a 3.5mm Mini Jack
Connect to a receiver.
5
Reset Button (under wall plate)
Press briefly to perform a software reset.
Press and hold for 10 seconds to perform a factory reset.
6
LINK LED
On when a WP-EN6 to KDS-DEC6 link is established and is transmitting A/V signals.
7
ON LED
Flashes during power up and lights when on.
8
STATUS LED
Identifies a device in a system. When sending a P3K FIND-ME command to the
system, the LED of the device to be identified flashes for 5 seconds.
9
CHANNEL Display
Displays the selected channel. If the channel number exceeds 99, the 100 indicator
turns on (for example, channel 124 appears as “24”).
10
Ring Tongue Terminal Grounding
Screw
Connect to grounding wire (optional).
11
RS-232 3-pin Terminal Block
Connector (Tx, Rx and common G)
Connect to an RS-232 controller device (to control a device on the decoder side)
12
Power Supply 2-pin Terminal Block
Connector
Connect to a power supply (if required). Connect GND to GND, +12V to +12V.
13
LAN/POE RJ-45 Connector
Connect to the network using recommended Kramer cables. Note that this port
supports power over Ethernet (PoE).

Step 3: Install WP-EN6
Insert the device into the in-wall box (note that first you need
to connect the LAN/POE RJ-45 Connector cable and/or
power) and connect the parts as shown in the illustration:
DECORA® design frames are included in US-D models.
DECORA® is a registered trademark of Leviton
Manufacturing Co., Inc.
We recommend that you use a US-D 2 gang US electrical
junction box (or their equivalent).
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your WP-EN6. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the WP-EN6.
RS-232 Configuration
Grounding the WP-EN6 (Optional)
RS-232 Control
1. Connect the ring tongue terminal to the building grounding point wire
(a green-yellow, AWG#18 (0.82mm2) wire, crimped with a proper
hand-tool is recommended).
2. Insert the M3x8 screw through the toothed lock washer, the tongue
terminal and the washer in the order shown above.
3. Insert the M3x8 screw (with toothed lock washer ring tongue terminal
and washer) into the grounding screw hole and tighten the screw.
Baud Rate:
115,200
Data Bits:
8
Stop Bits:
1
Parity:
None
For optimal performance, use the recommended Kramer cables available at www.kramerav.com/product/WP-EN6.
Using third-party cables may cause damage!
Step 5: Connect power
When accepting power from a PoE provider, there is no need to connect the 12V DC power supply.
Otherwise, connect the 12V power adapter (sold separately) to the device and plug the power supply into the mains electricity.
Safety Instructions
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.